Werner Retractables & Lifelines

Werner Poly-Dac Vertical Lifelines, 5/8 Inch Rope from 30 to 350 Feet, Lanyard-End Lines and More

Polyester and polypropylene rope lines with a snap hook end, sized to the climb, paired with 5/8 inch rope grabs and held to OSHA strength, separate-line and edge protection rules.

Werner Poly-Dac vertical lifelines give a climber or roofer a rope that runs from one overhead anchor down the full height of the work, so a rope grab can follow the worker instead of the anchor moving every few feet. Nation Wide Ladder helps you size the line, with L201 Poly-Dac rope in ten lengths from 30 to 350 feet, the L242050 and L242050W lines finished with a 3 foot lanyard, and Werner rope grabs made for 5/8 inch rope.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

What Werner Poly-Dac Rope Is Made Of and Who Uses It

Werner makes Poly-Dac as a three-strand rope of polyester and polypropylene blended together, 5/8 inch (16 mm) thick. Werner chose the blend for a line that stays light enough to handle on a roof, gives a comfortable grip and resists chafing, which counts on a Poly-Dac line that spends its working life against shingles, steel or masonry.

Every L201 Poly-Dac line has a snap hook at one end for the anchor connection, with the rest of the rope left plain so a grab can ride it. Roofers working down a pitch from a ridge anchor, structure climbers and crews working down a slope all use Werner Poly-Dac vertical lifelines this way, with the anchor fixed and the grab doing the traveling. Werner notes that fall protection is required from 6 feet in construction and 4 feet in general industry, which is the point where a roof or structure climb needs a line like this.

OSHA requires a separate vertical lifeline for each worker, apart from a narrow exception during elevator shaft construction, so plan on one Poly-Dac line per climber rather than a shared rope. The rest of the Werner lifeline family sits in our Werner retractables and lifelines range.

We help you count climbers and anchor points so each worker on the crew gets a Werner Poly-Dac line of the right length.

Werner Fall Protection L201030 30FT 5/8IN (14MM) Poly-dac Vertical Lifeline

Choosing Werner Poly-Dac Vertical Lifelines by Length, from 30 to 350 Feet

The L201 numbers end in the length. The L201030 is 30 feet, then come 35, 50, 75, 100, 125, 175, 200 and 225 feet and the 350 foot L201350, so a crew can match a Werner line to the height of the job instead of hauling a long surplus coil. Werner lists the 50 foot L201050 Poly-Dac line at about 6 pounds, which gives a feel for how weight builds on the longer coils, and Werner backs the L201 lines with a one-year warranty on its product listing.

Size the Poly-Dac rope from the anchor to the lowest point the worker will reach, with enough spare that the grab never runs near the free end. A vertical line far longer than needed adds weight on the roof and more rope to manage at the base, while a short one limits the work.

Two Werner Poly-Dac vertical lifelines arrive ready to connect differently. The L242050 Poly-Dac line with lanyard and the L242050W are 50 foot lines finished with a 3 foot lanyard and a double snap hook, which suits crews who want the connection end made up in advance.

Long Poly-Dac coils for Maine roofing crews can ride our regular weekly delivery run from New Hampshire.

Werner Fall Protection L201050 50FT 5/8IN (14MM) Poly-dac Vertical Lifeline, Snap Hook

Strength, Edge Protection and Grab Pairing for Vertical Poly-Dac Lines

OSHA sets a minimum breaking strength of 5,000 pounds for vertical lifelines and requires every lifeline to be protected against cuts and abrasion. The anchorage must carry 5,000 pounds per attached worker unless a qualified person designs it as part of a system with a safety factor of at least two. A Poly-Dac rope crossing a roof edge or a steel flange needs that protection where it bends.

Pair the rope with a grab Werner makes for 5/8 inch rope lifelines. The self-trailing L240002 rope grab and L250000 follow the climber without a hand on them, while the manual L240000 can be fixed at a set point for positioning or restraint, and Werner rates each of these grabs at a minimum breaking strength of 3,600 pounds. Werner also warns that parts from different makers may not be interchangeable, so keep the vertical line and grab within the Werner system.

Inspect the rope, snap hook and grab before each use, and take a Poly-Dac line out of service once it has arrested a fall.

At our Windham and Worcester showrooms you can handle the rope and try a grab on it before choosing a length.

Werner Fall Protection L201035 35FT 5/8IN (14MM) Poly-dac Vertical Lifeline

Werner Poly-Dac Lines Along the Whole Climb to the Anchor

A vertical rope only works once someone has set the anchor at the top, which means a ladder or other access to get there and a harness suited to the grab connection. Those pieces rarely all come from one maker, so planning access and tie-off together keeps the climb consistent.

To compare the manufacturers behind that access gear, visit our ladder and truck equipment brands hub.

Werner Fall Protection L201075 75FT 5/8IN (14MM) Poly-dac Vertical Lifeline

Quotes on Werner Poly-Dac Vertical Lifelines and Grabs

Three-strand 5/8 inch rope in ten lengths, lanyard-end options and matching grabs let each climber work from a line sized to the job. Tell us the anchor height and how many climbers you have, call 603-434-6911 in NH or 508-754-3030 in MA, and we will quote Werner Poly-Dac vertical lifelines with the grabs to match. See them in our Werner store or return to the Werner brand page.

Werner Poly-Dac Vertical Lifelines FAQs

What diameter is Werner Poly-Dac rope?

5/8 inch, which Werner gives as 16 mm, in a three-strand polyester and polypropylene blend.

Which Poly-Dac vertical lifelines come with a lanyard?

The L242050 and L242050W, 50 foot lines finished with a 3 foot lanyard and a double snap hook.

Can two workers share one Poly-Dac vertical line?

No. OSHA requires a separate vertical lifeline for each worker, with a narrow exception during elevator shaft construction.

Which Werner rope grabs fit Poly-Dac lines?

Werner makes the L240000, L240001, L240002, L250000 and L250001 for 5/8 inch rope lifelines, in manual and self-trailing designs.

How strong must Werner Poly-Dac vertical lifelines be?

OSHA 1926.502 sets a minimum breaking strength of 5,000 pounds for vertical lifelines and lanyards.

Need help choosing the right Werner equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder