Best Sellers
Truck Ladder Racks in Rail-Track Aluminum, Sliding, Steel Tube, Cap, Service Body and Headache Guard Designs and More
Drill-free aluminum rigs, fixed and sliding over-bed models, heavy steel tube, cap and service body mounts, and headache racks that carry ladders, compared by rating, mounting method and what shares the bed.
Truck ladder racks lift extension ladders, conduit, pipe and lumber over the bed so the floor stays free for boxes and material, and Nation Wide Ladder sizes each truck rack to the cab, bed and body, quotes the System One, TracRac, Holman, Weather Guard and Magnum models contractors order most, then installs it. Our best sellers cover aluminum over-bed rigs on rail tracks, sliding and fixed models, steel heavy-duty designs, cap and service body mounts, and headache racks that build into ladder carriers.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Aluminum Truck Ladder Racks That Mount Without Drilling the Bed
Aluminum is where many over-bed truck ladder racks start, since it skips the repainting a steel truck rack needs after winters on salted roads. System One rates its Heavy I.T.S. build, the System One Heavy Duty Contractor Rack, at 1,250 lb against 1,000 lb for the standard Contractor Rig. It stands on Pick-up Traks fixed to the inside lip of the bed rail, and once the Traks are on, System One says the trusses and accessories need no further holes in the truck. The whole rig comes off in about three to five minutes while the Traks stay on the rails, and the lighter System One Utility Rack carries a 600 lb working load on free-standing trusses.
TracRac by Thule models take a similar drill-free route. The TracOne is a fixed truck rack rated at 800 lb, the Pro 2 is the 1,000 lb contractor model with integrated tool box mounts, and the SR slides along vehicle-specific base rails at 1,250 lb so the bars move to suit each ladder or load. Thule ties every rating to a properly installed rack with the weight spread evenly. Holman adds the Pro IV, an HD aluminum truck rack, to a range that is otherwise built in steel.
We offer custom powder coating on new System One truck rack purchases, so a fleet can match its racks to its trucks from the day they go on.
Steel Truck Ladder Racks for Caps, Service Bodies and Heavy Daily Loads
Steel suits the truck that loads hard every day. Holman builds its Pro II heavy-duty rack from 2 inch high-tensile mechanical tube with a 0.083 inch wall, and the Holman 1200 Series Pro Rack adds to that design with a rear crossbar that swings out and locks open, an adjustable front leg mount and a standard Pro Wing wind deflector. The Holman Pro III covers medium-duty work. Weather Guard’s 1275-52-02 steel truck rack clamps to the stake pockets of a full-size bed with no drilling, carries 1,000 lb distributed evenly and has a tie-down loop on each leg.
Capped trucks and work bodies need their own truck ladder racks. Holman makes Clamp & Lock, drop down and combo HD aluminum ladder racks for most commercial caps in 6.5 and 8 foot sizes, usually with a separate mount kit, along with Pro II cap models for 78 and 96 inch beds and 6 inch taller legs that lift a Pro II over a cap. Service bodies take heavy-duty side channels matched to a standard or extended cab and an 8, 9 or 11 foot body, and the 1200 Series suits service and platform bodies as well.
Our truck and van department installs what we sell, mounting the rack, legs and side channels to suit the way your crew loads the truck.
Cab Protection, Load Ratings and Tie-Downs for Truck Ladder Racks
A headache rack guards the rear window when cargo slides forward, and several grow into full ladder carriers. Magnum builds each rack by hand in Waterville, Maine from welded aluminum, with a Low Pro about level with the cab that comes lit because it covers the third brake light, and Standard or High Pro versions about 3 inches taller. A Magnum rear rack add-on clamps to the bed and adjusts in width, or 5 inch side rails carry a rear bar rack, turning the headache rack into a ladder hauler. Weather Guard offers the hex 11906-52-01 for the most cab cover, the lighter half bar 11908-52-01 and the PROTECT-A-RAIL cab protector.
Published ratings deserve a careful read. System One notes there is no common industry standard for rack ratings and that driving, roads and suspension all affect real capacity, while Thule warns that the truck’s own limits may sit lower than the rack’s. A pickup hauling a full box and a stack of ladders may hit its payload limit before the rack hits its rating. Tie a long ladder or pipe at more than one crossbar, then check the straps again once the load has settled on the road.
Both of our locations keep Saturday morning hours, a good time to go over rack height, ratings and tie-down points with us without losing a working day.
Truck Ladder Racks Planned With Tool Boxes and Bed Gear
A rack settles what rides overhead, but the bed under it still holds boxes, slides or drawers, so the mounting points need planning together. System One hangs top-side and low-side boxes from Heavy I.T.S. gussets, and the TracRac Pro 2 has tool box mounts built in. Our pages on System One truck racks, the Holman truck rack range, Weather Guard ladder and headache racks and Magnum headache rack options break each maker down by model.
When you want those rack makers beside the box and ladder brands we stock, browse our truck equipment and ladder brands hub.
Quotes, Fitting and Delivery on Truck Ladder Racks
Nation Wide Ladder measures the cab, bed and any cap or body, then supplies and installs truck ladder racks from showrooms in Windham, New Hampshire and Worcester, Massachusetts, as part of our best-selling ladder and truck equipment. Our own trucks deliver door to door across Connecticut, Rhode Island, Massachusetts, New Hampshire, Vermont and Maine, so the rack, crossbars and tie-downs arrive together.
Truck Ladder Racks FAQs
Which truck ladder racks install without drilling?
System One rigs mount to Pick-up Traks on the bed rail lip, the TracRac TracOne and SR base rails are drill-free, and the Weather Guard 1275-52-02 clamps to the stake pockets.
How much weight can truck ladder racks carry?
Ratings run from 600 lb for the System One Utility Rack to 1,250 lb for the Heavy I.T.S. Contractor Rack and TracRac SR, but the truck's own payload limit still applies.
Can truck ladder racks go on a pickup with a cap?
Yes. Holman makes Clamp & Lock, drop down and combo ladder racks for most commercial caps, Pro II cap models, and 6 inch taller legs that lift a Pro II over a cap.
Are aluminum or steel truck ladder racks a better fit for winter roads?
Aluminum designs from System One, TracRac, Magnum and the Holman Pro IV resist rust without repainting, while steel models such as the Holman Pro II suit the heaviest daily loading.
Can a headache rack carry ladders?
Yes. A Magnum headache rack paired with its rear rack add-on, or with side rails and a rear bar rack, becomes a ladder carrier.
Do you install truck ladder racks?
Yes. We install every truck rack style we sell, plus truck boxes and other truck equipment, and we offer custom powder coating on new System One rack purchases.
Need help choosing the right ladder or truck equipment?
Talk to the team or send us your list and we will put a quote together.









