Best Sellers
Roofing Equipment for Lifting, Footing and Edge Protection, From Platform Hoists to Roof Brackets, Guardrails and More
RGC platform hoists and track, Acro roof brackets, ridge hooks and chicken ladders, chimney brackets, Pitch Hopper wedges, laminated planks, and guardrail, warning line and anchors for pitched and flat roofing.
Roofing equipment has to solve three problems on every job, getting material to the eave, giving the crew footing on the slope and guarding the edge, and Nation Wide Ladder quotes the RGC, Acro and Pitch Hopper roofing equipment contractors order most for each one. Our range covers platform hoists and accessories, roof brackets, chimney brackets, ridge hooks, chicken ladders, roofing wedges, laminated planks, guardrail and perimeter systems, warning lines and roof anchors.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Shop Roofing Equipment by Type
Ladder HoistsRGC Classic, Pro and PHD ladder hoists in 200, 250 and 400 pound capacities, with track, carriers and…
Roof BracketsAcro fixed and adjustable roof brackets, chimney brackets, Ultimate Ridge Hooks and chicken ladders, matched to your pitch…
Roof GuardrailsAcro and Tie Down roof guardrails for pitched, flat and parapet edges, with posts, bases and warning lines…
Roofing Equipment That Lifts Bundles to the Eave
Material handling is the first piece of roofing equipment most crews buy, because OSHA’s ladder rules make carrying a shingle bundle up an extension ladder hard to defend. A platform hoist, also called a ladder hoist, runs a small powered platform up an aluminum track that leans on the building like a ladder. RGC, the trademark of Reimann & Georger Corp., builds the models we list. We list its Classic and Pro lines at 200 or 400 pounds of capacity, with 28 or 44 feet of track and a choice of Briggs & Stratton gas, Honda gas or electric power, and the RGC Classic 200 climbs at 220 feet per minute.
Accessories widen what one hoist moves. RGC sells 4 and 8 foot track sections, a telescope support required on any run over 28 feet, a 7 inch plywood carrier, a solar panel carrier and a 6 foot roller angle guide for 400 pound hoists. Our ladder hoists page compares capacities, drives and track, and the RGC platform hoists page covers the maker’s full range. RGC is clear that the track carries material only and is never climbed.
Our team checks eave heights, ground conditions and typical loads with you, so the roofing equipment we quote reaches the eaves you work.
Roofing Equipment for Footing on the Slope
Once material reaches the eave, the crew needs somewhere to stand. Acro roof brackets nail through the shingle course and hold a plank level across the slope, in 16 inch versions set at 45, 60 or 90 degrees and 19 inch versions at 45 degrees, plus the 29038 adjustable bracket that sets at 33, 45, 60 or 90 degrees. Under OSHA’s scaffold rules a plank on brackets is a roof bracket scaffold, which means each bracket has to suit the pitch and goes on with nails wherever nailing is practical. Chimney brackets carry a platform around a chimney, and the Ultimate Ridge Hooks we list hold roof or chimney brackets from the ridge without penetrating the sheathing.
Climbing gear rounds out this roofing equipment. A single ladder becomes a roof ladder with the Acro 11084 ridge hook, rated for 300 pounds, while Acro’s 11601 chicken ladder sections link up to four 6 foot lengths behind the 11610 hook. The Pitch Hopper roofing wedge gives a temporary working surface on asphalt roofs from walking pitch to 12/12, held by friction, in 24 and 32 inch lengths. Our roof brackets page sorts every bracket, hook and ladder by pitch and plank.
Both of our showrooms open on Saturday mornings, so a crew can collect brackets, hooks and other roofing equipment before a weekend tear-off.
Edge Protection Roofing Equipment for Pitched and Flat Roofs
OSHA requires fall protection for residential construction, steep roof work and low-slope roofing once an unprotected edge sits 6 feet or more above a lower level, and guardrails protect everyone inside them at once. Acro builds the guardrail and perimeter roofing equipment we list. The 12070 steep pitch and 12075 open edge systems install like roof brackets and interleave with shingles, the 12060 flat roof, 12090 parapet and 12045 vertical systems mount to commercial roofs and walls, and the 21000 X and heavy duty warning line sets mark a work area on low-slope roofs. Tie Down adds a 10 foot universal guardrail and a 110 foot stack rack kit rated for roofs up to a 2/12 pitch.
Work outside the rails calls for a roof anchor and harness. The Werner A525400 post anchor is a permanent galvanized steel anchor with a 360 degree loading direction and a 5,000 pound minimum breaking strength. Our roof guardrails page compares each edge system, and the Acro roofing equipment page covers the maker behind most of them.
Every week our trucks run from New Hampshire into Maine, which lets crews there top up posts, rails or warning lines mid-job.
Choosing Roofing Equipment by Roof Pitch and Height
OSHA sorts roofs by pitch, and that split decides much of the roofing equipment a crew carries. A roof sloped more than 4 in 12 counts as steep, and one at 4 in 12 or less counts as low-slope. Steep roof work with an edge 6 feet or more up calls for guardrails with toeboards, safety nets or personal fall arrest, so pitched jobs lean on roof brackets, guardrail brackets that nail on with them, and ridge hooks or chicken ladders for the climb. Low-slope roofing also allows a warning line combined with another method, or on roofs 50 feet or less wide a safety monitoring system alone, which is why flat roof crews carry warning line sets and parapet or base plate guardrails.
Height and roof surface shape the rest of the roofing equipment list. A 28 foot hoist track covers lower eaves, while taller walls need the 44 foot setup with its telescope support. Slate, metal and shake roofs favor roofing hardware that holds from the ridge rather than nailing through the surface, such as the Ultimate Ridge Hooks, rated at 1,750 pounds at a 45 degree angle and adjustable from 4/12 to 12/12.
Call 603-434-6911 in New Hampshire or 508-754-3030 in Massachusetts with the pitch, eave height and edge length of your next roof, and we quote the roofing equipment that covers it.
Roofing Equipment Within One Plan From Ground to Ridge
The hoist, the brackets and the rails meet at the same eave, so laying out that roofing equipment together decides where bundles land, where the crew stands and which edges stay guarded. Extension ladders for the climb, laminated planks for the brackets and a truck rack to haul it all belong in the same plan.
If you want to set ladder, rack and fall protection makers next to your roofing gear, start with our brands for ladders, roofing and truck equipment hub.
Roofing Equipment Quoted for Every Stage of the Job
For more than 50 years Nation Wide Ladder has outfitted roofers and contractors, with showrooms in Windham, New Hampshire and Worcester, Massachusetts and our own trucks covering Connecticut, Rhode Island, Massachusetts, New Hampshire, Vermont and Maine. We quote roofing equipment by eave height, pitch and edge length, so lifting, footing and edge protection arrive on one order, and our best sellers add the ladders and truck boxes that travel with them.
Roofing Equipment FAQs
What roofing equipment does a pitched roof job need?
Usually a way to lift material, such as a platform hoist, roof brackets and planks for footing, and edge protection such as guardrails or a personal fall arrest system once the edge is 6 feet or more above a lower level.
Which platform hoists are in your roofing equipment range?
Classic and Pro platform hoists from RGC, rated for 200 or 400 pounds, with 28 or 44 feet of track and gas or electric power.
What is a Pitch Hopper roofing wedge?
A roofing wedge that gives a temporary working surface on asphalt roofs from walking pitch to 12/12. It holds by friction and comes in 24 and 32 inch lengths.
Does roofing equipment for flat roofs differ from pitched roofs?
Yes. Pitched roofs use guardrail brackets that nail on like roof brackets, while flat roofs use base plates, parapet clamps, wall mounts and warning lines such as the Acro 12060, 12090, 12045 and 21000.
Can I climb the track of a roofing hoist?
No. The track is built for material alone, and RGC warns crews never to climb or ride it.
Need help choosing the right ladder or truck equipment?
Talk to the team or send us your list and we will put a quote together.









