Resources
Van Mark and Alum-A-Brake Siding Brakes Compared by Throat Depth, Hinge, Capacity, Length, Cutters and More
Fourteen, 19.5 and 20 inch throats, published bending limits for aluminum, vinyl, steel and copper, hem sizes, lengths and weights, and the cutting and measuring kit each line adds.
Siding crews comparing Van Mark and Alum-A-Brake portable brakes are choosing between two American makers with different ideas about throat depth, hinges and built-in cutting, and Nation Wide Ladder supplies both, so we can set them side by side for your work. We cover Van Mark's light-duty, TrimMaster, Metal Master 20 and Industrial Metal Master 20 EZ lines with the TrimCutter, Multi Gauge and Coil Dispenser, against the Alum-A-Brake Ultima QS, QCS and QMS with their coil holder, legs and wheel kit.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Throat Depth, Hinges and Bending Capacity on Van Mark and Alum-A-Brake Models
Throat depth decides how far into a sheet a brake can reach. Van Mark builds its light-duty and TrimMaster brakes with a 14 inch throat and notes that a typical residential trim piece is about 8 inches wide, while its Metal Master 20 lines reach 20 inches for wide soffit and roofing trim. Every Alum-A-Brake in the Ultima Q series has a 19.5 inch throat, which sits between the two Van Mark depths.
The hinge sets the smallest hem. Van Mark’s traditional hinge auto-measures a 3/4 inch bend for covering one-by fascia, and its POWERslot hinge, used on the TrimMaster and Metal Master, sets 5/8 inch for the tight pockets vinyl and fiber cement need. Alum-A-Pole fits the Alum-A-Brake with Power Lock snap clamping, a replaceable hardened stainless steel jaw edge and a replaceable PVC hinge edge, and anodizes the frame so it does not leave oxidation stains on coil.
Published limits use different measures, so read them carefully. Van Mark rates its light-duty and Metal Master 20 brakes for 0.027 inch aluminum, the TrimMaster for 0.032 inch, and all three for 29 gauge steel and 24 ounce copper, with the Industrial Metal Master 20 EZ rated to 0.050 inch aluminum and 20 gauge galvanized steel. The Alum-A-Brake is rated for 0.024 inch aluminum coil, 0.035 inch vinyl coil, 28 gauge soft steel and 16 ounce copper. The Alum-A-Brake siding brakes page sets out those ratings in full.
Our team helps you select the right products by checking the coil, metal and hem sizes you use against both makers’ published limits.
Lengths, Weights and Built-In Cutting on Each Van Mark and Alum-A-Brake Line
Van Mark offers more sizes. Its lighter lines run from 2 feet to 12 feet 6 inches and the industrial line from 6 feet 6 inches to 14 feet 6 inches, so a 10 foot 6 inch Van Mark TrimMaster weighs 123 pounds, a matching Metal Master 20 148 pounds and the industrial model 259 pounds. Alum-A-Pole builds each Ultima model at 5 feet 11 inches, 7 feet 10 inches and 10 feet 6 inches, from 70 pounds for a short QS to 162 pounds for a long QMS.
The cutting approach differs too. Van Mark mounts its accessories on the AccuTrack rails of the brake, where the TrimCutter slices clamped stock up to 24 gauge painted steel and the Multi Gauge shows bend angle, while a free-standing Coil Dispenser feeds the roll. The Alum-A-Brake QCS builds a track-mounted Qcut into the brake, and the QMS adds measuring arms, four Maximizers and a removable table, with a coil holder that carries its own slitter. A QS can take the Qcut parts later.
Free in-person consultations at our Windham, NH and Worcester, MA showrooms let you compare Van Mark and Alum-A-Brake weights and cutters before you choose.
Which Crews Lean Toward Van Mark Brakes or an Alum-A-Brake Station
Van Mark suits crews whose work sets the hinge or the metal. Installers forming tight J-channel pockets around vinyl or fiber cement often want a POWERslot hinge, and roofers bending painted steel valley pans, rake edges and ridge caps look to the Industrial Metal Master 20 EZ, which ships with its own stand. Van Mark sells tune-up kits by model, uses standard fasteners that leave the warranty intact, and covers each brake with a one-year limited warranty.
The Alum-A-Brake suits siding crews who want one station from one maker. The QMS puts cutting and measuring on the brake from day one, the tool-free legs keep it level, and the wheel kit lets it follow pump jack staging from one elevation to the next, which matters to crews already on Alum-A-Pole poles. Both makers say their brakes are made in the USA. The full Van Mark siding brakes and accessories range and the Alum-A-Brake Ultima line show every model we list.
Our own trucks deliver door to door across New England, so either brake can reach your shop or van without a pickup run.
Van Mark and Alum-A-Brake Stations Beside Staging and Truck Racks
A brake is one station on a siding job, with ladders or pump jacks on the wall and a truck or van rack that has to carry a brake up to 14 feet 6 inches long. Our Van Mark brand overview also covers the stands and support gear that travel in the van with each brake.
To weigh the ladder, staging and rack makers that sit around either brake, browse our ladder and truck equipment brands hub.
Getting Van Mark and Alum-A-Brake Quotes From One Team
Nation Wide Ladder has served siding and roofing contractors for over 50 years, and we quote Van Mark and Alum-A-Brake models on the same request, matched to the metal you bend, the hems you form and the van or truck that carries the brake.
Van Mark and Alum-A-Brake FAQs
Which has the deeper throat, Van Mark or Alum-A-Brake?
The Van Mark Metal Master 20 lines reach 20 inches, the Alum-A-Brake 19.5 inches and the Van Mark light-duty and TrimMaster brakes 14 inches.
Which Van Mark brake makes a 5/8 inch hem?
Van Mark brakes with the POWERslot hinge, such as the TrimMaster and Metal Master 20, set a 5/8 inch hem. The light-duty line sets 3/4 inch.
Can the Alum-A-Brake bend vinyl coil?
Alum-A-Pole rates the Ultima Q series for 0.035 inch vinyl coil, along with 0.024 inch aluminum coil, 28 gauge soft steel and 16 ounce copper.
Which Van Mark model bends the heaviest steel?
The Industrial Metal Master 20 EZ, rated for 20 gauge galvanized and 24 gauge painted and stainless steel.
Do Van Mark and Alum-A-Brake models come with a cutter?
The Alum-A-Brake QCS and QMS include the Qcut. Van Mark sells the TrimCutter separately to run on the AccuTrack rails of its cam-lock brakes.
What lengths do Van Mark and Alum-A-Brake brakes come in?
Van Mark runs from 2 feet to 14 feet 6 inches across its lines. The Alum-A-Brake comes in 5 feet 11 inches, 7 feet 10 inches and 10 feet 6 inches.
Need help choosing the right ladder or truck equipment?
Talk to the team or send us your list and we will put a quote together.








