Resources

Alum-A-Pole and ReechCraft PowerPole Compared, Foot-Pumped Jacks, Drill-Driven Climbers, Heights, Loads and More

Pump jack poles against drill-climbed aluminum masts, rated loads per jack and per climbing unit, freestanding and tied heights, stage widths, footprint and setup on a house exterior.

Comparing Alum-A-Pole and ReechCraft PowerPole systems starts with how each one lifts the platform, and Nation Wide Ladder carries both, so our team can set them side by side for the walls you work on. Alum-A-Pole uses foot-pumped Pro-Jack units on aluminum poles with linked stages, workbenches and end rails, while ReechCraft drives a climbing unit up an aluminum mast with a 1/2-inch drill, using outrigger bases, V-braces, standoff ties, stages and a one-person basket.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

How Alum-A-Pole Pump Jacks and the ReechCraft PowerPole Raise a Platform

Alum-A-Pole builds a classic pump jack system. Structural aluminum poles come in 6, 12, 18 and 24 foot lengths, the Alum-A-Joint splices two together, and an Alum-A-Pole Pro-Jack rides each pole. Pressing the foot pump climbs the jack, and the Pro-Jack telescopes to 27 inches and carries three backup systems that Alum-A-Pole calls the Axial Perma-Clutch, Saf-T-Brake and Auto-Glide. The details of each part sit on our Alum-A-Pole Pro-Jack page.

The PowerPole replaces the foot with a drill. Its mast is built from 6 and 12 foot aluminum sections carrying a steel track, and a climbing unit with a PowerTrak gearbox runs up that track when a standard 1/2-inch drill turns it. ReechCraft says the drill drive is roughly three times the speed of pumping, and our published PowerPole specification gives 25 feet per minute at half load and 15 feet per minute at full load. The gearbox has an integrated overspeed brake, a manual descent crank is offered for emergency lowering, and the mast tilts up from the ground without anyone first going onto the roof.

Our team helps you select between Alum-A-Pole and ReechCraft for your crew, weighing how often you raise the stage and who does the lifting.

Alum-A-Pole Pro-Jack Pump Jacks

Rated Loads, Working Heights and Ties for Alum-A-Pole and ReechCraft Systems

Alum-A-Pole and the PowerPole maker publish ratings differently, so compare like with like. Alum-A-Pole rates its complete system for two workers and 500 pounds with a 4 to 1 safety ratio, lab rates its poles to 5,000 pounds and the Pro-Jack to 4,000 pounds, and says the system is approved by OSHA to a 50 foot shoulder working height. ReechCraft rates each PowerPole climbing unit at 650 pounds, not counting the platform, or 1,300 pounds for a twin-mast pair.

Heights follow different rules too. Alum-A-Pole poles are braced back to the building as OSHA 1926.452(j) requires, at the bottom, the top and other points as needed. A ReechCraft PowerPole reaches a 24 foot work height freestanding when the outrigger base and a V-brace are fitted, and ReechCraft takes it to a 75 foot work height with midspan ties no more than 16 feet apart plus one at the top. ReechCraft lists OSHA 1926.451 and 1926.452(j), OSHA Subpart M and ANSI A10.8 and A10.32 as the codes it designs the PowerPole to, so both systems answer to the same pump jack paragraph. Our Alum-A-Pole pump jack scaffolding and ReechCraft PowerPole scaffolding pages carry the full ratings.

Free in-person consultations at our Windham, NH and Worcester, MA showrooms let you compare Alum-A-Pole and ReechCraft ratings with our team against your tallest wall.

Alum-A-Pole Pole Scaffold

Choosing Between Alum-A-Pole Stages and a PowerPole Mast for Each House

Alum-A-Pole suits crews that stage long walls and want one walkway along a whole side, which is how most Alum-A-Pole owners use it. Every Alum-A-Scaff stage sits at the same rail height, so stages link from pole to pole without limit, in 14, 20 and 24 inch widths and lengths up to 24 feet. A workbench rides the same poles, end rails close the open ends, and siding crews can pair the poles with the Alum-A-Brake from the same maker. Alum-A-Pole says other brands’ parts will not connect properly to its system, so keep it all Alum-A-Pole.

The ReechCraft PowerPole suits crews who move often and work on tight or planted lots. Each mast lands on a 10 by 10 inch base foot, twin masts carry stages up to 40 feet long and 28 inches wide, and a single mast with the one-person basket gives a 36 by 26 inch deck for trim or window work. Standoff ties clear a roof edge, and the PowerPole accessories cover each of those parts. Its maker also advises keeping ladder access to the platform and a spare cordless drill on hand in case power fails.

Our trucks run regular weekly deliveries to Maine from New Hampshire, so crews there can add Alum-A-Pole stages or ReechCraft parts mid-season.

ReechCraft PowerPole Accessories

Alum-A-Pole, ReechCraft PowerPole and the Rest of the Exterior Kit

Whichever system raises the platform, the crew still needs ladders to reach it, planks or stages to stand on and a truck rack to carry 24 foot poles or 12 foot mast sections. Each brand overview, Alum-A-Pole and ReechCraft, shows the full range around its pole system.

When you are lining up ladders and racks from other makers to go with your staging, compare them in our ladder and truck equipment brands hub.

Alum-A-Pole

Quoting Alum-A-Pole and ReechCraft PowerPole Setups Together

Nation Wide Ladder has served contractors and homeowners for over 50 years, and we can price Alum-A-Pole and ReechCraft PowerPole systems on one quote, sized to your wall heights, run lengths and crew, so you can weigh the pump against the drill on real numbers.

Alum-A-Pole and ReechCraft PowerPole FAQs

What is the main difference between Alum-A-Pole and ReechCraft PowerPole?

Alum-A-Pole Pro-Jacks climb aluminum poles by foot pump, while the ReechCraft PowerPole climbing unit is driven up a steel track on an aluminum mast by a 1/2-inch drill.

Which carries more, Alum-A-Pole or ReechCraft?

They rate differently. Alum-A-Pole rates its whole system for two workers and 500 pounds, while ReechCraft rates each PowerPole climbing unit at 650 pounds, not counting the platform.

Can a ReechCraft PowerPole stand without wall ties?

Yes, to a 24 foot work height with the outrigger base and a V-brace. Above that it needs ties, up to a 75 foot work height.

How high can Alum-A-Pole scaffolding go?

Alum-A-Pole says its system is approved by OSHA to a 50 foot shoulder working height using the Alum-A-Joint.

Can I mix Alum-A-Pole and ReechCraft parts?

No. Alum-A-Pole says other makers' parts will not connect properly to its system, and the PowerPole accessories are built for ReechCraft masts.

What happens if the drill fails on a ReechCraft PowerPole?

ReechCraft advises keeping ladder access to the platform at all times and a spare cordless drill on hand, and offers a manual descent crank.

Need help choosing the right ladder or truck equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder