Resources
Roof Brackets and Guardrails for Roofing Crews, From 19 Inch Plank Brackets to Open Edge Posts, Warning Lines and More
OSHA's 6 foot trigger for residential, steep and low-slope roofing, top rail height and load, fixed and adjustable plank brackets, ridge hooks, chicken ladders and edge posts that nail on like a bracket.
Footing on the slope and protection at the edge are separate problems on every pitched roof, and roofing crews solve them with roof brackets and guardrails, which Nation Wide Ladder supplies and helps lay out for each job. We cover fixed 19 inch and adjustable plank brackets, ridge hooks and chicken ladder hooks, open edge guardrail brackets for eaves and rakes, flat roof, parapet and vertical guardrail systems, warning lines and the OSHA rules that decide which a roof needs.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
OSHA Edge Rules Behind Roof Brackets and Guardrails on Pitched Roofs
OSHA sets the trigger at 6 feet. Under 29 CFR 1926.501, a worker doing residential construction, or working on a steep roof, with an unprotected edge 6 feet or more above a lower level needs a guardrail system, a safety net or a personal fall arrest system, and on steep roofs those guardrails must carry toeboards. On low-slope roofs a warning line can be combined with a guardrail, net, fall arrest or safety monitoring. Guardrails then have to meet 1926.502, with the top rail 42 inches above the working surface, plus or minus 3 inches, and the system able to withstand at least 200 pounds outward or downward without deflecting lower than 39 inches.
Roof brackets answer a different rule. OSHA treats a plank on roof brackets as a roof bracket scaffold under 1926.452(h), so the brackets must fit the pitch, give the plank a level support and be nailed in place unless nailing is impractical, in which case 3/4 inch manila rope or its equivalent holds them. A bracket gives a roofer somewhere to stand, but on its own it does not guard the edge, which is why most pitched-roof jobs need both pieces of roof equipment.
Our team checks the pitch, edge type and height on each roof with you, so the roof brackets and guardrails we quote cover the edges that trigger OSHA’s rule.
Fixed and Adjustable Roof Brackets for Planks on Every Pitch
The most common roof bracket is a fixed 45 degree contractor bracket. Acro builds its 19 inch version for a 2×6 or 2×8 plank, sells it in boxes of 12, and gives it four offset nail slots so it cannot slide up the nails, a stiffening rib and a square bottom for knocking it out once the course is done. Acro says the extra length leaves more room between the plank and the shingle the bracket is nailed through.
Crews who change pitch from job to job often carry an adjustable roof bracket as well. Acro’s 29038 is a 16 inch steel bracket that sets at 33, 45, 60 or 90 degrees, takes 2×6, 2×8 or 2×10 planks at every angle and a 2×12 at 33 or 45 degrees, and folds flat. For climbing, the Acro 11084 ridge hook turns a single ladder into a roof ladder with a 300 pound capacity, and the 11610 chicken ladder hook joins up to four 6 foot sections. OSHA asks for crawling boards, or chicken ladders, to run from the peak to the eaves in roof work. The Acro roof brackets and ridge hooks page covers each model.
Both of our locations open Saturday mornings, so you can pick up another box of roof brackets before a weekend tear-off.
How Guardrails Mount Beside Roof Brackets at Eaves, Rakes and Flat Roofs
On a pitched roof, edge guardrails can install much like a bracket. Acro’s 12075 open edge system is a roof bracket with a guardrail post holder, giving a slide guard, a toeboard and a rail in one piece that nails on, interleaves with shingles and taps out. Acro rates it for pitches up to 16/12, for rake edges at any pitch and for eave edges under 4/12. On these guardrails, posts go no more than 8 feet apart with construction grade 2x4s as the rails, lapped at least 6 inches inside a post bracket.
Flat and commercial roofs use other guardrails. Acro’s 12060 flat roof plate can be left behind when the job ends, the 12090 parapet system clamps walls 4 to 24 inches wide and the 12045 vertical system mounts to walls, beams or joists. A warning line is the low-slope alternative where OSHA allows it, held between 34 and 39 inches high, flagged at least every 6 feet and set no closer than 6 feet from the edge. Acro’s 21000 X set has four 42 inch posts and 100 feet of flags. Our Acro guardrail systems page lists each model.
Our own trucks deliver door to door across New England, so posts, brackets and lumber holders for a large roof can land at the job.
Roof Brackets, Guardrails and Personal Fall Arrest Together
Guardrails protect everyone inside them, but work outside the rails, at a skylight or on a ridge cap, often calls for a personal fall arrest system. That means a roof anchor and a harness, such as the Werner roof anchors and Werner harnesses, alongside the edge equipment from Acro.
When you are lining up ladders and fall protection from several makers around your roof equipment, our ladder and truck equipment brands hub sets them side by side.
Quoting Roof Brackets and Guardrails for New England Roofs
Nation Wide Ladder has served roofers and builders for over 50 years, and we quote roof brackets and guardrails by roof pitch, edge length and plank size, so a crew gets footing and edge protection on the same order and the same truck.
Roof Brackets and Guardrails FAQs
Do roof brackets count as fall protection?
No. OSHA treats planks on roof brackets as a roof bracket scaffold for footing. An edge 6 feet or more up still needs a guardrail, net or personal fall arrest system.
How high must roof guardrails be?
OSHA 1926.502 sets the top rail at 42 inches above the working surface, plus or minus 3 inches, and the system must withstand at least 200 pounds.
What angles do adjustable roof brackets set to?
The Acro 29038 adjustable roof bracket sets at 33, 45, 60 or 90 degrees and folds flat for storage.
How far apart do posts on roof guardrails go?
Acro lists a maximum of 8 feet between posts when construction grade 2x4s are used as rails.
Can roof brackets and guardrails share one installation?
On pitched roofs, yes. The Acro 12075 open edge bracket nails on and interleaves with shingles like a roof bracket while holding a guardrail post.
How must roof brackets be secured?
OSHA 1926.452(h) calls for nails unless nailing is impractical, in which case first-grade manila rope at least 3/4 inch thick or an equivalent is used.
Need help choosing the right ladder or truck equipment?
Talk to the team or send us your list and we will put a quote together.








