Van Mark Siding Brakes & Accessories
Van Mark Metal Master 20 Brakes, With Pro-Grade MM Models, Industrial IM Models, 20 Inch Throats, Stands and More
Two 20 inch throat lines compared, the lighter MM series for wide siding trim and the industrial IM series for roofing panels, with lengths, weights, bending limits and stands.
Wide soffit panels, valley pans and ridge caps will not fit a standard 14 inch brake, and the Van Mark Metal Master answers that with a 20 inch throat, supplied across New England by Nation Wide Ladder. We list the pro-grade MM series, from the 2 foot MM260 to the 12 foot 6 inch MM1260, and the Industrial Metal Master 20 EZ, or IM series, from the 6 foot 6 inch IM665 to the 14 foot 6 inch IM1465, which ships with its own stand.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
What the Van Mark Metal Master 20 Inch Throat Allows
Throat depth limits how wide a piece can be bent back from its edge. A 14 inch throat handles typical residential trim, but metal roofing trim, wide soffit and architectural panels need more. Van Mark first engineered its 20 inch casting for the industrial IM series, a brake for roofing crews bending painted steel on site, and Van Mark describes that throat as the deepest working pocket among portable brakes.
Siding and residential roofing contractors then asked Van Mark for a lighter brake with the same reach, and the pro-grade MM series was the result. It keeps the 20 inch throat and the POWERslot hinge with its 5/8 inch auto-measured hem, in a lighter frame meant to set up beside a pickup or work van.
The industrial version targets metal roofing and sheet work. Van Mark lists W-style valley pans, rake edges, soffits, roof flashing, wide hip and ridge caps and HVAC duct and plenum work among its uses, and says it bends and hems 24, 26 and 29 gauge painted steel on site.
Our team will check the widest pieces and heaviest stock you bend, then point you to the Van Mark Metal Master version that suits them.
Van Mark Metal Master MM and IM Models by Length
Pro-grade MM series. The Van Mark MM series Metal Master 20 comes in six lengths from 2 feet to 12 feet 6 inches. Weights run from 52 pounds for the MM260 to 148 pounds for the 10 foot 6 inch MM1060 and 194 pounds for the MM1260. Van Mark notes the stronger 20 inch casting means fewer castings per length, with four on the MM1060.
Industrial IM series. The Van Mark Industrial Metal Master 20 EZ comes in five lengths from 6 feet 6 inches to 14 feet 6 inches. It is far heavier, from 217 pounds for the IM665 to 259 pounds for the IM1065 and 385 pounds for the IM1465, with five to ten castings.
The 12 foot 6 inch MM1260 adds dual bending and locking handles, as do the two longest IM models, while the IM1065 has dual bending handles. Longer brakes need a longer van, truck rack or trailer, so measure before choosing.
Free in-person consultations at our Windham NH or Worcester MA showroom let you weigh each Van Mark length against the vehicle that will carry it.
Van Mark Metal Master Bending Limits and Construction
Van Mark’s maximum thickness figures assume standard material properties. For the IM series it lists 0.050 inch aluminum in 3003-H14, 20 gauge galvanized steel, 24 gauge painted Grade D and 304L stainless steel, 36 ounce soft copper and 0.050 inch zinc. Its spec sheet for the pro-grade MM series lists 0.027 inch aluminum and 29 gauge galvanized, painted and stainless steel. Check your exact stock against the model with us or with Van Mark before buying.
Both lines use the patented Van Mark cam lock, which pairs an aluminum cam with a UHMW polyethylene wedge, with two castings at each clamping station and dual base rails. The Power Lock bar clamps along the whole bending edge with a 150 degree radius for easier 180 degree hems, and its AccuTrack rails take the TrimCutter, TrimFormer and Multi Gauge. Van Mark lists newer castings that are lighter yet stronger, and covers each brake with a one-year limited warranty.
Bring a sample of your coil or panel to either showroom on a Saturday morning and we can review it against these limits with you.
Stands and Setup for a Van Mark Metal Master
A 20 inch throat brake needs a stand sized for it. For the pro-grade MM series, Van Mark lists the USA2EZ, USA2 and UNL2 stands and the 3035 wheel kit, all made for 20 inch throat brakes. The IM series includes the Master Stand EZ, with center-weighted wheels and a low-profile extended platform, and it breaks down in seconds for transport. Extended leverage handles give four lifting points on the hinge for even bends.
Set up on level ground so the brake does not twist, and keep wide panels supported as they feed in. Clean the clamping faces before bending painted steel to avoid marking it, and secure the brake in the van or trailer with the handles released.
Van Mark uses standard nuts, bolts and pull pins, and standard replacement hardware does not affect the warranty. Long IM brakes are heavy, so plan on two people for loading and unloading.
Our own trucks deliver door to door across New England, so even a 385 pound IM1465 and its stand can come straight to your yard.
The Van Mark Metal Master Within a Roofing Crew Setup
On a roofing job the brake sits between the coil supply and the roof, with staging, ladders and fall protection around it. Brake length also has to fit the trailer or rack that moves it between jobs.
Each of those makers is listed in our ladder and truck equipment brands hub, so you can compare them.
Get Pricing on a Van Mark Metal Master
Nation Wide Ladder has served roofers and siding contractors for over 50 years, and we quote each Van Mark Metal Master with the stand and cutter it needs. Compare other Van Mark siding brakes and accessories, read the Van Mark overview, or browse our Van Mark store.
Van Mark Metal Master FAQs
What throat depth does the Van Mark Metal Master have?
Both the pro-grade MM series and the industrial IM series have a 20 inch throat.
What is the difference between the MM and IM Van Mark Metal Master lines?
The MM series is a lighter pro-grade brake for siding and residential roofing trim. The IM series is an industrial brake for roofing panels with higher capacities and an included stand.
What lengths does the Van Mark Metal Master come in?
The MM series runs from 2 feet to 12 feet 6 inches, and the IM series from 6 feet 6 inches to 14 feet 6 inches.
How heavy a sheet can the industrial Van Mark Metal Master bend?
Van Mark lists 0.050 inch aluminum, 20 gauge galvanized steel, 24 gauge painted and stainless steel and 36 ounce soft copper.
Which stands fit the Van Mark Metal Master?
The USA2EZ, USA2 and UNL2 stands and 3035 wheel kit fit the MM series. The IM series includes its own stand.
Need help choosing the right Van Mark equipment?
Talk to the team or send us your list and we will put a quote together.






