ReechCraft range

ReechCraft PowerPole Scaffolding Systems, With Drill-Powered Climbing Units, Outrigger Bases, Wall Ties, Stages and More

Single-mast and twin-mast pole systems for exterior walls, from a freestanding 24 foot outrigger setup to a tied 75 foot run, with a 650 pound climbing unit on each aluminum mast.

Raising a plank by hand on pump jacks slows every exterior job, and Nation Wide Ladder speeds that work with ReechCraft PowerPole scaffolding, configured by our team for the heights and walls you face. We supply single-mast setups with the one-person basket, twin-mast setups carrying a stage, and the outrigger bases, V-braces, standoff ties and SpeedRail rails that hold each configuration in place.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

Who Uses ReechCraft PowerPole Scaffolding and on Which Exterior Jobs

Siding installers, painters, window and gutter crews and remodelers working on houses and small commercial walls are the core users. ReechCraft built the PowerPole to replace pump jack systems, and it says the drill-driven design is about three times the speed of pumping, with no pump strokes to strain a worker’s back. Because the mast tilts up from the ground, a crew can stand it without first getting onto the roof.

The footprint matters on residential lots. ReechCraft describes the PowerPole as landscape-friendly, since each mast lands on a 10 inch base foot rather than a wide frame, which helps between foundation plantings, along driveways and in the narrow gap between two houses. A single mast with the one-person basket gives fast access for trim, caulking or a window swap, while two masts and a stage cover a long wall of siding. Contractors who rent equipment out also use ReechCraft PowerPole scaffolding because it packs into a pickup or trailer.

Frame scaffolding still makes sense where a crew and pallets of material sit on one deck for weeks. For the quick, repeated setups of residential exteriors, pole scaffolding that one or two people can raise in minutes is the closer match.

Our own trucks deliver door to door across New England, so the masts and stages for your first PowerPole job can arrive at the house rather than your shop.

ReechCraft PowerPole

ReechCraft PowerPole Configurations, From a Freestanding Mast to Tied Twin Poles

Every setup starts with a ReechCraft PowerPole mast built from 6 and 12 foot aluminum sections joined by couplers, with a climbing unit riding its steel track. ReechCraft rates that climbing unit at 650 pounds, excluding the platform, and 1,300 pounds for two units working as a pair.

Freestanding with outriggers. Clamp the outrigger base to the mast, rest a V-brace against the wall, and the system reaches a 24 foot work height without tying into the building. ReechCraft sets the outrigger stabilizers roughly 5 feet from the wall and 4 feet apart, so the mast leans into the structure.

Tied for height. Anchor the top of the mast at 32 feet, or at 40 feet with the outrigger base and V-brace, and the pole runs without midspan ties, provided you have separate access to fix the top tie. ReechCraft takes the system to a 75 foot work height with midspan ties every 16 feet.

Platforms. Twin masts carry stages up to 40 feet long and 28 inches wide, and the single-person basket gives a 36 by 26 inch deck.

Our team checks the wall height, roof overhang and stage length before you buy, so the configuration on your quote matches the house.

ReechCraft 4022465 – 10 in. x 10 in. Base Foot

Speeds, Brakes and OSHA Codes for ReechCraft PowerPole Scaffolding Crews

The specification text we publish for the system gives a top climbing speed of 25 feet per minute at half the rated load, 15 feet per minute at full load and a 30 foot per minute maximum lowering speed. The gearbox has an integrated overspeed brake that stops the platform if it descends too fast, and a safety locking lever on the climbing unit. A manual crank for emergency lowering is offered as an option.

ReechCraft lists the codes it designs PowerPole to as OSHA 1926.451 and 1926.452(j) for scaffolds, OSHA Subpart M for fall protection, and ANSI A10.8 and A10.32. Its FAQ adds practical rules for a power cut, which are to keep ladder access to the platform at all times as OSHA requires, carry a spare cordless drill, use locking or secured extension cords and fit a surge protector that resets at a lower amperage than the panel breaker. Midrail posts set 8 feet apart or closer, with 2x4s run as the midrail and toerail, complete the guarding on a stage.

We keep regular weekly deliveries running from New Hampshire to Maine, so crews there can add ReechCraft PowerPole scaffolding parts mid-season without a long wait between runs.

ReechCraft 4022179 – Platform Support with PowerLatch Connector

ReechCraft PowerPole Scaffolding Next to Ladders and the Bronco Tripod

A PowerPole crew still needs ladders for the climb onto the stage and for short tasks around the base, and many also carry a pair of ReechCraft Bronco tripods for first-story work on sloped ground. Seeing how each access product covers a different band of height helps you spend on the right one.

If you are weighing other makers for the ladder side of the job, our ladder and truck equipment brands collection lines them up in one place.

ReechCraft PowerLatch Assembly

Get ReechCraft PowerPole Scaffolding Quoted for Your Crew

Tell us the wall heights, stage lengths and number of masts, and we will price ReechCraft PowerPole scaffolding to fit the job. See the systems in our power scaffolding store, add parts from our PowerPole accessories range, or compare the wider ReechCraft scaffolding lineup.

ReechCraft PowerPole Scaffolding FAQs

How fast does ReechCraft PowerPole scaffolding climb?

Our published specification gives 25 feet per minute at half the rated load and 15 feet per minute at full load, with lowering up to 30 feet per minute. ReechCraft describes it as about three times the speed of a pump jack.

Can ReechCraft PowerPole scaffolding stand without wall ties?

Yes, up to a 24 foot work height when the mast has the outrigger base and a V-brace resting against the wall.

What is the load rating of a ReechCraft PowerPole climbing unit?

ReechCraft rates it at 650 pounds per climbing unit, not including the platform, or 1,300 pounds for a twin configuration.

How long a stage can a PowerPole system carry?

ReechCraft lists platform sizes up to 40 feet long and 28 inches wide for twin-mast setups.

What happens if the drill loses power on a PowerPole?

ReechCraft says ladder access must be kept at all times, as OSHA requires, and recommends a spare cordless drill on the platform. A manual descent crank is offered as an option.

Need help choosing the right ReechCraft equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder