Brand spotlight
ReechCraft Scaffolding With PowerPole Pole Systems, Bronco All-Terrain Tripods, Climbing Units, Ties, Rails and More
Drill-powered aluminum pole systems for siding, painting and window work, three-legged tripods for staging on uneven ground, and the climbing units, braces, ties and rails that complete a setup.
Pump jacks and frame staging eat hours on a house exterior, and Nation Wide Ladder helps crews work faster with ReechCraft scaffolding, matched to the job by our team and delivered across New England. We supply the drill-powered PowerPole system with its climbing units, pole sections, outriggers, braces, ties, baskets and rails, plus the three-legged Bronco for staging planks on sloped or broken ground.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
What ReechCraft Scaffolding Does on a House Exterior
ReechCraft builds portable access equipment in Fargo, North Dakota, and the two lines we carry both solve exterior jobs where ladders run out of reach and full frame staging is overkill. The PowerPole is a pole scaffold you climb with a 1/2-inch drill, so siding, painting, window and trim crews can raise a plank to the work and lower it again without pumping. The Bronco is a folding aluminum tripod that sets a level plank over slopes, steps and rocks.
Two categories organize our ReechCraft scaffolding pages. The PowerPole scaffolding page explains the complete system, its ratings and its setups, from a 24 foot freestanding mast to a fully tied 75 foot run. The PowerPole accessories page goes part by part through the climbing unit, pole sections, base, ties and rails, so you can extend a kit you already own or replace one worn piece. Start with the system if you are new to ReechCraft, or go to the accessories when you already know your configuration.
Shop ReechCraft Scaffolding by Category
ReechCraft PowerPole ScaffoldingDrill-powered ReechCraft PowerPole pole scaffolding for siding, paint and window crews, from 24 ft freestanding to 75 ft…
ReechCraft PowerPole AccessoriesReechCraft PowerPole climbing units, masts, couplers, ties, braces, rails and baskets to extend or repair a pole system.
ReechCraft Scaffolding Roots, From a 1993 Start to a Fargo Factory
ReechCraft, Inc. was founded in 1993 and still ships its products from its own manufacturing plant in Fargo, North Dakota, rather than through a chain of warehouses. The company describes its focus as portability and fast setup and teardown, aimed at cutting the labor a crew spends getting into position. Its current lineup runs from PowerLift personnel lifts and the PowerMast climbing system to the PowerPole and the Bronco, and the last two are the ReechCraft scaffolding products we carry for contractors and homeowners.
Most of the ReechCraft range shares one idea, which is to move people and material vertically with a standard electric drill and a gearbox instead of a pump or a gas engine. On the PowerPole that means the PowerTrak drive, a gearbox and drill brace that climb a steel track on an aluminum mast. ReechCraft sells through dealers across the United States and Canada, publishes operator safety manuals for each product and offers training courses and certification for crews that want formal instruction on its equipment.
We have served homeowners and contractors for over 50 years, so a crew trying ReechCraft scaffolding for the first time can lean on people who have watched access methods change across decades of New England jobs.
PowerPole Systems, Accessories and the Bronco in Our ReechCraft Scaffolding Range
PowerPole systems. Our ReechCraft PowerPole scaffolding page covers the complete setup, built from aluminum mast sections, a drill-powered climbing unit on each pole and a plank or stage between them. ReechCraft pitches it for residential exteriors because it sets up without roof access and leaves a small footprint in landscaped yards.
PowerPole parts and add-ons. The ReechCraft PowerPole accessories we list include 6 and 12 foot pole sections, couplers, the 10 by 10 inch base foot, the outrigger base, two V-brace styles, standoff ties, a platform support, the PowerLatch assembly, SpeedRail rails and a single-person basket.
Bronco. The ReechCraft 4026200 Bronco scaffolding system is a three-legged aluminum tripod that works like an adjustable sawhorse. Each leg telescopes on its own, so a pair can hold a level plank where the ground slopes or steps.
Mixing the two. Plenty of crews own both, using ReechCraft scaffolding on the PowerPole for second-story walls and a pair of Broncos for the porch roof edge, the walkout basement side of the house or interior work on a stepped floor. Both lines share the same aluminum build, so a kit of either loads into a pickup with room left for planks.
Our team checks wall heights, plank lengths and the parts already in your trailer, so each ReechCraft scaffolding order arrives complete and sized to the house in front of you.
Load Ratings, Tie Heights and OSHA Codes Behind ReechCraft Scaffolding
ReechCraft rates each PowerPole climbing unit at 650 pounds, not counting the work platform, or 1,300 pounds for a twin-pole configuration. With the outrigger base and V-brace in place the system reaches a 24 foot work height without a wall tie. ReechCraft gives a maximum work height of 75 feet, which needs midspan ties no more than 16 feet apart plus one at the top, and platforms up to 40 feet long and 28 inches wide. The gearbox carries an integrated overspeed brake, and a manual descent crank is offered for emergency lowering.
On standards, ReechCraft lists OSHA 1926.451 and 1926.452(j) for scaffolds, OSHA Subpart M for fall protection and ANSI A10.8 and A10.32 as the codes that apply to PowerPole. Its own FAQ also reminds users that OSHA requires ladder access to the platform at all times. For the Bronco, ReechCraft rates each tripod at 300 pounds and a pair at 600 pounds, and states that it complies with ANSI and OSHA safety standards.
Call our New Hampshire office at 603-434-6911 or Massachusetts at 508-754-3030 with your planned heights, and we will quote the ReechCraft scaffolding ties and braces that rating calls for.
Where ReechCraft Scaffolding Fits Among Ladders, Planks and Staging
Few exterior jobs run on one access method. A PowerPole run usually shares the site with extension ladders for the climb up, laminated or aluminum planks for the walkboard and, on bigger commercial walls, conventional frame staging. Picking the access product means looking at the whole house, which is why it helps to compare manufacturers side by side before committing a crew to one system.
Before you settle on a setup, look through our ladder and truck equipment brands to see the other access makers we stock next to ReechCraft.
Choosing Between ReechCraft PowerPole Scaffolding and a Bronco Setup
Start with height. The Bronco gives a level platform between 3 and 5 feet high, which ReechCraft says lets most users reach roughly 11 feet, so it suits first-floor siding, window and masonry work, especially on sloped lots where sawhorses rock. Each Bronco folds flat and weighs 16 pounds, with legs that adjust in 1.5 inch steps and a base spread up to 42 inches. ReechCraft rates it for platforms up to 24 inches wide.
Once the work climbs past a single story, the PowerPole is the ReechCraft scaffolding answer. Mix 6 and 12 foot pole sections to reach the height you need, and choose the outrigger base if you want a freestanding 24 foot setup or the standoff ties when the mast has to clear a roof edge. Single-worker tasks such as trim repair suit the one-person basket, while two masts and a stage handle long runs of siding. Bring a spare cordless drill, which ReechCraft recommends keeping on the platform.
Budget for the whole kit, not just the masts. ReechCraft scaffolding on poles needs a base foot, couplers and a climbing unit per mast, plus the ties or outriggers your wall calls for, and the scaffolding stage or walkboard itself. ReechCraft states that replacement parts are available for most models, which keeps an older system working.
Both of our showrooms, in Windham, NH and Worcester, MA, offer free in-person consultations, so you can talk through a PowerPole or Bronco layout with our team before ordering.
Order ReechCraft Scaffolding From Our New England Team
When the job calls for a drill-driven pole system or a tripod that levels itself on rough ground, we quote ReechCraft scaffolding to order and deliver it on our own trucks. Browse the complete ReechCraft store range, or send your parts list through our Request a Quote form.
ReechCraft Scaffolding FAQs
Where is ReechCraft scaffolding made?
ReechCraft says it ships its products from its own manufacturing facility in Fargo, North Dakota. The company was founded in 1993.
How much weight can a ReechCraft PowerPole climbing unit lift?
ReechCraft rates each climbing unit at 650 pounds, not including the work platform, or 1,300 pounds for a twin configuration.
How high can ReechCraft scaffolding go?
The PowerPole reaches a 24 foot work height freestanding with the outrigger base and V-brace, and up to 75 feet with midspan ties every 16 feet. The Bronco gives a 3 to 5 foot platform, or a working height of about 11 feet.
What powers the ReechCraft PowerPole?
A standard 1/2-inch drill drives the PowerTrak gearbox on the climbing unit. The gearbox includes an integrated overspeed brake and a safety locking lever.
How much does a ReechCraft Bronco hold?
ReechCraft rates one Bronco at 300 pounds and a pair at 600 pounds, with platforms up to 24 inches wide.
How do I get a price on ReechCraft scaffolding?
We quote every order. Use the Request a Quote form or call 603-434-6911 in New Hampshire or 508-754-3030 in Massachusetts.
Need help choosing the right ReechCraft equipment?
Talk to the team or send us your list and we will put a quote together.









