Alum-A-Pole Pole Scaffold
Alum-A-Pole Pro-Jack Pump Jacks, With Three Backup Safety Systems, a Saf-T-Crank Handle, Saf-T-Lok Chain and More
How the jack climbs an aluminum pole, its 27 inch telescoping arm and 4,000 lb test, the Perma-Clutch, Saf-T-Brake and Auto-Glide backups, OSHA pump jack rules and spring and roller checks.
We quote the Alum-A-Pole Pro-Jack for crews who need to raise and hold a scaffold stage on aluminum poles, safely and a few inches at a time, as the work climbs a wall. Nation Wide Ladder lists the PROJACK pump jack with its telescoping arm, three backup safety systems, Saf-T-Crank handle and Saf-T-Lok chain, and our team helps you count the jacks, poles and workbenches a wall calls for.

- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
How an Alum-A-Pole Pro-Jack Raises and Holds a Scaffold Stage
A pump jack is the moving part of a pole scaffold. One Alum-A-Pole Pro-Jack clamps around each pole, a stage spans between two of them, and the crew raises the platform by pumping the foot pedal on each jack in turn until the deck reaches the next course. Alum-A-Pole describes the same foot-powered mechanism as raising or lowering the platform, so the deck can follow the work down the wall as easily as up it.
The arm on each Alum-A-Pole Pro-Jack telescopes to 27 inches, which sets how far the stage sits out from the pole. The jack is structural aluminum, like the poles it rides on, which keeps it light enough to lift onto a pole by hand. Every stage needs a jack at each end, so a run of linked stages uses one per pole, and the Pro-Bench workbench rides the same pole above it to hold tools and materials at working height. Siding, painting and window crews favor this setup because the platform can stop at any height on the pole rather than at fixed frame levels.
Send us the wall run and stage lengths, and we will quote the number of Alum-A-Pole Pro-Jack units and poles that run needs.
Alum-A-Pole Pro-Jack Safety Systems, Saf-T-Crank and Saf-T-Lok Chain
Alum-A-Pole builds three independent backup safety systems into every Pro-Jack, which it names the Axial Perma-Clutch, the Saf-T-Brake and Auto-Glide. The idea behind three separate systems is redundancy, so the stage stays held if one mechanism is ever compromised. Alum-A-Pole does not publish a detailed breakdown of how each one works on the pages we checked, so the instruction manual that ships with the jack is the place to learn the operating sequence.
Two other features show up on our PROJACK pump jack listing. The Saf-T-Crank handle is self-storing, so it folds out of the way when not in use, and it has an anti-spin feature that keeps it from whipping around under load. The Saf-T-Lok chain secures the stage to the jack and doubles as an anti-theft measure when the setup is left standing overnight. Alum-A-Pole uses the same chain on its stages, whose male and female ends lock onto the jack or bench, and the company states that the Alum-A-Pole Pro-Jack exceeds the OSHA 500 pound, 4 to 1 safety ratio.
Our Windham, NH and Worcester, MA showrooms offer free in-person consultations, where you can see how the Alum-A-Pole Pro-Jack crank and chain work with our team.
Pro-Jack Ratings and the OSHA Pump Jack Rules Alum-A-Pole Crews Follow
Our listing describes the Alum-A-Pole Pro-Jack as tested to 4,000 pounds, and Alum-A-Pole rates the complete pump jack system for two people and 500 pounds with a 4 to 1 overall safety ratio. The poles it climbs are lab rated to 5,000 pounds.
Federal rules add their own conditions. OSHA’s pump jack paragraph, 29 CFR 1926.452(j), requires each bracket to have two positive gripping mechanisms so it cannot slip, and requires poles braced to the structure at the bottom, the top and other points as needed. When a Pro-Jack has to pass a brace on the way up, an additional brace goes about 4 feet above it and stays until the original is replaced. A workbench may never serve as a scaffold platform, though it can act as a toprail if it meets the guardrail criteria in 1926.451. Under that general scaffold rule, pump jack platforms can be as narrow as 12 inches, a competent person inspects the scaffold before each shift, and anyone more than 10 feet above a lower level needs fall protection.
Having served contractors for over 50 years, we can help you list the braces, rails and fall protection those rules call for around your Alum-A-Pole Pro-Jack setup.
Checking Springs, Rollers and the APC Bolt on an Alum-A-Pole Pro-Jack
Alum-A-Pole publishes a short list of checks that keep an Alum-A-Pole jack gripping as designed. Each Pro-Jack should carry four springs, two on the lower posi and two on the upper posi, and any missing spring should be replaced before the jack goes back on a pole. Rollers that have gone flat or worn should be replaced too, since they are part of how the jack tracks up the pole. The APC bolt should be tightened by hand only, never with a wrench.
Alum-A-Pole also warns against mixing other makers’ products into the system, which means replacement springs, rollers and jacks should be Alum-A-Pole parts. A good habit is to check springs and rollers when the scaffold comes down at the end of a job, so worn parts are ordered before the next one starts. Keep the rubber face of each pole pointed away from the building so the jack grips the side it was designed to grip, and keep the whole aluminum setup clear of power lines.
Our own trucks deliver door to door across New England, so replacement Alum-A-Pole Pro-Jack units can reach the job between phases.
Alum-A-Pole Pro-Jack Units Among the Rest of an Exterior Crew’s Gear
A Pro-Jack only covers the lifting. The same crew still needs ladders to set braces and reach the roof, a truck rack that carries poles and stages, and often a siding brake on the ground beside the scaffold, so the jack is one piece of a larger kit.
If you are comparing the makers behind the rest of that kit, you will find them in our ladder and truck equipment brands hub.
Quote Alum-A-Pole Pro-Jack Units for Your Next Wall
A platform that climbs with the work keeps a siding or painting crew on the wall, and Nation Wide Ladder quotes the Alum-A-Pole Pro-Jack together with the poles, braces and stages it supports. See the full system on our Alum-A-Pole pump jack scaffolding overview, visit the Alum-A-Pole brand page, or browse the Alum-A-Pole store.
Alum-A-Pole Pro-Jack FAQs
How much weight is an Alum-A-Pole Pro-Jack tested to?
Our listing gives the jack a 4,000 pound test, and Alum-A-Pole rates the complete system for two people and 500 pounds with a 4 to 1 safety ratio.
What are the three Alum-A-Pole Pro-Jack backup systems?
Alum-A-Pole names them the Axial Perma-Clutch, the Saf-T-Brake and Auto-Glide, three independent backups built into every Pro-Jack.
How far does the Pro-Jack arm telescope?
It telescopes to 27 inches, the same reach as the Alum-A-Pole Pro-Bench workbench.
How many springs should an Alum-A-Pole pump jack have?
Four, two on the lower posi and two on the upper posi. Alum-A-Pole says to replace any missing spring and any flat or worn roller.
Can I use an Alum-A-Pole Pro-Jack on another brand of pole?
Alum-A-Pole advises against mixing other manufacturers' products with its system, so pair the Pro-Jack with Alum-A-Pole poles.
What does the Saf-T-Lok chain do on a Pro-Jack?
It secures the stage to the jack and helps deter theft when the scaffold is left standing.
Need help choosing the right Alum-A-Pole equipment?
Talk to the team or send us your list and we will put a quote together.


