Alum-A-Pole range
Alum-A-Pole Pump Jack Scaffolding, With Aluminum Poles, Pro-Jacks, Stages, Workbenches, End Rails, Braces and More
Aluminum pole lengths from 6 to 24 feet, Pro-Jack lifting and backup systems, stage widths, bracing and the OSHA pump jack rules that shape a safe exterior wall setup.
Keeping a platform at the right height as a wall goes up is the daily challenge on siding, trim and roof-edge work, and Nation Wide Ladder meets it with Alum-A-Pole pump jack scaffolding, planned with our team for each elevation and delivered across New England. The scaffolding system covers aluminum poles and joints, Pro-Jack pump jacks, Alum-A-Scaff stages, workbenches, end rails, braces and the Saf-T-Net, all designed to work together on houses and low-rise buildings.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Alum-A-Pole Pump Jack Scaffolding Product Lines
Alum-A-Pole Aluminum Poles and Pole PackagesAlum-A-Pole pump jack poles in 6 to 24 foot lengths, the pole joint, and the two and three…
Alum-A-Pole Pro-Jack Pump JacksThe Alum-A-Pole Pro-Jack pump jack, its three backup safety systems, ratings, OSHA rules and the checks that keep…
Alum-A-Pole Stages and End RailsAlum-A-Pole stages in 16, 20 and 24 foot lengths, their 500 lb rating and the SNERS end rails…
Where Alum-A-Pole Pump Jack Systems Earn Their Place
Pump jack scaffolding works best on long, flat wall faces. Siding installers, painters, window crews and remodelers use it to keep the platform parallel to the wall and adjust height a few inches at a time as each course goes up. Because the parts are aluminum, two people can carry poles and stages around a house and move the setup to the next elevation the same day. Alum-A-Pole began in 1980 when siding contractor Carl Anderson built an aluminum pole to replace wood poles, which is why the system fits the rhythm of cladding work so closely.
Alum-A-Pole names siding, general construction, roofing, painting and window installation as the trades it designs for, and describes pump jack scaffolding as suited to residential and light commercial jobs, including sites where the ground is uneven. A foot-operated pump on each jack raises the platform up the poles and the jacks bring it back down, so the deck follows the work. Every Alum-A-Scaff stage sits at the same rail height, so stages link pole to pole into one walkway along a full side of a house, and federal rules allow pump jack platforms as narrow as 12 inches, against 18 inches for most supported scaffolds.
Tell us the wall heights and the trades on the job, and our team will help you decide how Alum-A-Pole pump jack scaffolding fits that house.
Alum-A-Pole Poles, Pump Jacks, Stages and Rails in One Scaffolding System
Poles.Alum-A-Pole pump jack poles are structural aluminum with bonded rubber grips and permanent safety stops, in 6, 12, 18 and 24 foot lengths with a limited lifetime warranty. The Alum-A-Joint splices two poles together with two separate stops for taller walls.
Pro-Jack. The Alum-A-Pole PROJACK pump jack telescopes to 27 inches and carries three independent backup systems that Alum-A-Pole calls the Axial Perma-Clutch, Saf-T-Brake and Auto-Glide. Its Saf-T-Crank handle stores itself and resists spinning, and a Saf-T-Lok chain holds the stage in place while deterring theft.
Stages, bench and rails. Alum-A-Scaff stages use square rungs and open-hole decking for grip underfoot and link end to end across a run. The workbench telescopes to the same 27 inches and keeps tools within reach, and the end rail system closes the open end of a stage to help prevent walk-off falls. We stock end rails in 14 inch (SNERS-14) and 20 inch (SNERS-20) sizes, and they attach to Alum-A-Pole stages only.
Braces and net. The powder-coated Alum-A-Brace comes in folding and rigid versions, with a swivel that sets it at different angles against a wall or roof, and the 22 foot Saf-T-Net is a folding net rated as fall protection for people. For a starting kit, Alum-A-Pole pole packages bundle the main components in one order.
Our Windham, NH and Worcester, MA showrooms offer free in-person consultations, so you can go over each Alum-A-Pole part with our team before you order.
Pump Jack Ratings and OSHA Rules for Alum-A-Pole Scaffolding Crews
Alum-A-Pole rates the full scaffolding system for two workers and 500 pounds with a 4 to 1 safety ratio, says it holds OSHA approval for a 50 foot shoulder working height, and lab rates the poles to 5,000 pounds and the Pro-Jack to 4,000 pounds.
The OSHA pump jack paragraph, 29 CFR 1926.452(j), requires two positive gripping mechanisms on each bracket and rigid triangular bracing that ties poles to the structure at the bottom, the top and other points as needed. When the pump jack has to pass a brace, a temporary brace goes about 4 feet above it and stays until the original is reinstalled, and a workbench cannot serve as the standing platform. Under 1926.451, decking has to fill each working level with gaps of no more than 1 inch, the front edge stays within 14 inches of the wall unless guardrails or fall arrest cover it, and poles need base plates and mud sills or other firm footing. Anyone more than 10 feet above a lower level needs fall protection, and on a supported scaffold placed in service since 2000 the toprail sits 38 to 45 inches above the deck.
We have served contractors for over 50 years, and our team will help you list the braces, rails and base plates these rules call for on your walls.
Alum-A-Pole Pump Jack Scaffolding Beside the Alum-A-Brake on Siding Jobs
On most siding jobs the scaffolding and the brake work side by side. Crews stage the wall on pump jacks and bend wraps, fascia and drip edge from trim coil on the ground nearby, which is why the company also builds Alum-A-Pole siding brakes to sit alongside its poles. With the wheel kit, the brake can follow the scaffolding from one elevation to the next.
To weigh Alum-A-Pole against the other makers on your list, look through our ladder and truck equipment brands hub.
Sizing and Inspecting an Alum-A-Pole Pump Jack Setup for Each Wall
Measure the highest point you need to reach, then choose pole lengths so the joints land where they are practical to assemble on the ground. Count poles by stage span, since every stage needs a pole and pump jack at each end and linked stages share poles along the run. On a wall of roughly 40 feet, two 20 foot stages linked end to end need three poles and three jacks. Alum-A-Pole stages come in 14, 20 and 24 inch widths and up to 24 feet long, and the end rails you order have to match the stage width. Where a stage passes its support, OSHA asks for at least 6 inches of overlap unless the end is cleated or hooked, and no more than 12 inches of overhang on a platform of 10 feet or less. Count braces per pole rather than per run, plus a spare for passing.
Before each shift, a competent person checks for visible defects. Alum-A-Pole adds its own checks, which call for the rubber on each pole to face away from the building, the APC bolt tightened by hand, all four springs present on each pump jack and rollers free of flat spots. Aluminum scaffolding conducts electricity, so keep the setup clear of power lines, and keep every component within the brand, since Alum-A-Pole says other parts will not connect properly.
Our own trucks deliver door to door across New England, with weekly runs to Maine from New Hampshire, so long poles and stages reach your site without a trailer of your own.
Get Alum-A-Pole Pump Jack Scaffolding Priced for Your Walls
When the wall is long and the crew is small, a platform that climbs with the work keeps the crew installing instead of rebuilding, and we price Alum-A-Pole pump jack scaffolding by quote to match your wall heights and run length. Send them through a quote request, browse the Alum-A-Pole scaffold category, or return to the Alum-A-Pole brand overview.
Alum-A-Pole Pump Jack Scaffolding FAQs
What lengths do Alum-A-Pole pump jack poles come in?
Alum-A-Pole lists 6, 12, 18 and 24 foot poles. The Alum-A-Joint splices two poles together for taller walls.
How many people can work on Alum-A-Pole pump jack scaffolding?
The manufacturer rates the scaffolding for two workers and 500 pounds combined, including any material on the stage.
How high can Alum-A-Pole pump jack scaffolding go?
Alum-A-Pole says the system holds OSHA approval for a 50 foot shoulder working height, reached by splicing poles with the Alum-A-Joint.
How often do pump jack poles need bracing?
OSHA requires rigid triangular bracing at the bottom, the top and other points as necessary, plus a temporary brace about 4 feet above any brace the pump jack has to pass. Follow the Alum-A-Pole instructions for the specific setup.
Do Alum-A-Pole end rails fit other brands of stage?
The end rail system attaches to Alum-A-Pole stages only, and we stock it in 14 inch and 20 inch sizes.
What should be checked on an Alum-A-Pole pump jack before each shift?
OSHA calls for a competent person to inspect for visible defects before each shift. Alum-A-Pole also recommends confirming the four springs on each pump jack and checking rollers for flat spots or wear.
Need help choosing the right Alum-A-Pole equipment?
Talk to the team or send us your list and we will put a quote together.










