Resources

Trim Coil Bending on the Job Site, From Dispensing and Cutting to Measured Bends, Hems, Wraps, Drip Edge and More

Holding the roll off the ground, cutting stock to width with a track cutter or slitter, repeat measuring, hem sizes for fascia and vinyl pockets, coil thickness limits and a level station near the wall.

Doing your own trim coil bending at the house lets a siding crew match color and profile exactly instead of waiting on shop-formed pieces, and Nation Wide Ladder supplies the brakes and accessories that make it work. We cover each step from roll to finished wrap, from roll dispensers and holders to track-mounted cutters, slitters, gauges and measuring arms, plus hems for fascia and vinyl pockets, the thickness each brake handles and how to set up the station.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

From Roll to Wrap, the Steps of Trim Coil Bending at the House

Every trim piece, from a window wrap to a fascia cover or drip edge, starts as a roll of trim stock. The first job is keeping that roll clean and under control. Van Mark’s CD24 Coil Dispenser holds the trim coil on two non-marring rollers under a quick-release tension roller, so it stays wound tight and out of the wind while stock feeds straight into the brake. The Alum-A-Brake coil holder mounts to the brake or its legs, carries a built-in track-mounted slitter and is designed for 24 by 50 inch rolls.

Next comes cutting to width and length. A knife leaves a rough edge, so both makers put a cutter on the brake. Van Mark’s 3017 TrimCutter rides the AccuTrack rails on four tracking wheels and slices clamped stock with case-hardened knives, and the Alum-A-Brake QCS and QMS carry a track-mounted Qcut. The Van Mark TrimCutter and Coil Dispenser page covers that pair. Measuring follows. Van Mark’s Multi Gauge shows bend angle and the 1.5 inch distance to the cutter line, while Alum-A-Pole’s measuring arms and Maximizers hold a set distance for repeat cuts and bends, so a crew can bend trim coil without pencil marks.

Our team helps you select the dispenser, cutter and gauge that suit the bending your trim crew does most often.

Van Mark TrimCutter and Coil Dispenser

Trim Coil Thickness, Hems and the Bending Limits Brake Makers Publish

Every brake has a published limit, and trim coil bending stays inside it. Van Mark rates its light-duty brake for 0.027 inch aluminum and the Van Mark TrimMaster for 0.032 inch, with both handling 29 gauge steel and 24 ounce soft copper. Alum-A-Pole rates the Alum-A-Brake for 0.024 inch aluminum coil, 0.035 inch vinyl coil, 28 gauge soft steel and 16 ounce copper, and Van Mark suggests calling the factory before bending anything outside standard metal properties.

On a bending brake, the hinge sets the hem. A traditional Van Mark hinge auto-measures 3/4 inch, which fits neatly over one-by fascia and rake boards, while the POWERslot hinge sets 5/8 inch for the tighter pockets that vinyl siding and fiber cement need. A Power Lock bar with a 150 degree bending radius eases the second step of a 180 degree hem. Before bending a new color or profile, run a test piece of scrap so the hem sits right on the house. Finish matters too, since Alum-A-Pole anodizes the Alum-A-Brake so it does not leave oxidation stains on the trim, and keeping clamping faces and wear strips clean stops painted trim coil from being marked. The Alum-A-Pole siding brakes page lists every rating.

Both of our locations open Saturday mornings, so you can bring a sample of your trim stock in and check it against these limits with us.

Van Mark Mark II TrimMaster

Setting Up a Trim Coil Bending Station Beside the Wall

Place the station close to the wall where the trim goes up, which cuts down trips up and down the ladder or staging. Set the bending brake on level ground or on legs that keep it level, since a twisted frame bends a long trim piece unevenly. Alum-A-Pole’s tool-free APLEG legs fit any Ultima Q brake, and its wheel kit lets the station follow pump jack staging from one elevation to the next. Van Mark sizes its stands and wheel kits to the throat of each brake.

Square the dispenser to the brake so trim coil feeds straight into the jaws, and lock the tension roller before pulling stock. Run the cutter in one smooth pass and let the knives do the work, then check the edge after the first cut on a new roll of painted stock. Wipe grit off the rails and tracking wheels at the end of the day. A 10 foot 6 inch brake, such as the longest Alum-A-Brake Ultima, bends a full-length trim piece in one pass. Keep finished trim flat and off the ground until it goes up, since a kinked wrap is hard to straighten.

Our own trucks deliver door to door across New England, so a brake, coil holder and legs can arrive together at the job.

Alum-A-Pole Ultima Siding Brakes

Trim Coil Bending Alongside Staging and Ladders

The trim bending station sits at the base of the wall, with ladders or pump jack scaffolding carrying the finished pieces up and a truck rack carrying the brake home. The Van Mark range shows the full set of cutting and support tools around its brakes.

For the ladder, staging and rack makers that complete a siding setup, explore our ladder and truck equipment brands hub.

Alum-A-Pole Pole Scaffold

Equipping Trim Coil Bending With Our Team

Nation Wide Ladder has served siding contractors for over 50 years, and we quote the brakes, cutters and roll holders that trim coil bending calls for, matched to your coil, your hems and the way your crew sets up at the house.

Trim Coil Bending FAQs

What tools do I need for trim coil bending on site?

A portable brake, a way to hold the roll such as a roll dispenser or holder, a cutter or slitter, and a gauge or measuring arms for repeat bends.

How thick a trim coil can a siding brake bend?

Van Mark rates its light-duty brake for 0.027 inch aluminum and the TrimMaster for 0.032 inch, and Alum-A-Pole rates the Alum-A-Brake for 0.024 inch aluminum coil and 0.035 inch vinyl coil.

What hem size suits fascia trim?

A traditional hinge sets a 3/4 inch hem that fits over one-by fascia. A POWERslot hinge sets 5/8 inch for tighter vinyl and fiber cement pockets.

How do I stop trim coil unraveling on site?

Use a dispenser or holder. Van Mark's CD24 holds the roll under a tension roller, and the Alum-A-Brake coil holder keeps the roll secure on the brake.

Can I cut trim coil on the brake?

Yes. Van Mark's TrimCutter rides the AccuTrack rails, and the Alum-A-Brake QCS and QMS have a track-mounted Qcut.

Why does trim coil bending leave marks on painted stock?

Grit on clamping faces and wear strips can mark the finish, so keep them clean. Alum-A-Pole anodizes its brake to avoid oxidation stains on trim.

Need help choosing the right ladder or truck equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder