Resources

Ladder Jacks and Planks for Siding and Painting, From Short and Long Body Jacks to Stages, Ladders and More

How a two-ladder jack scaffold goes together, stage widths and plank ratings, OSHA's 20 foot height cap and 10 foot fall arrest trigger, overhang limits and the check before each shift.

Ladder jacks and planks turn two extension ladders into a working platform along a wall, and the challenge for siding and painting crews is keeping that platform inside OSHA's scaffold rules as it moves along the house. Nation Wide Ladder supplies Werner short body and long body ladder jacks with the Type IA and Type IAA extension ladders Werner recommends for them, and our team helps you match jacks, stage width, plank length and fall protection.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

How Ladder Jacks and Planks Go Together on Two Extension Ladders

A ladder jack hooks onto the rungs of an extension ladder and carries one end of a stage or plank, while a second ladder and jack carry the other end. OSHA requires the jack to bear on the side rails and rungs or on the rungs alone, and where it bears only on rungs, the bearing area must cover at least 10 inches of each rung. The supporting ladders must meet OSHA’s ladder rules, job-made ladders are not allowed, and each ladder must be placed, fastened or equipped to prevent slipping.

Werner builds three jacks for this work. The AC10-14-02 short body is a two-rung model for stages up to 14 inches wide, the AC10-20-02 long body is a two-rung model for stages up to 20 inches, and the AC10-20-03 grips three rungs and also takes 20 inch stages. Each setup needs a matching pair of jacks on matching ladders, set at the same angle and hung at the same rung height. Werner notes that all three adjust quickly in the field, which helps when leveling a stage between ladders on uneven ground. Our Werner ladder jacks and Werner AC10 ladder jacks ranges compare them in detail.

Our team checks jack model, stage width and ladders together, so the ladder jacks and planks you order work as one setup from the first wall.

Werner Ladder Jacks

Choosing Planks and Stages Wide and Strong Enough for Ladder Jacks

OSHA sets a 12 inch minimum width for a ladder jack scaffold platform, and Werner’s jacks take 14 inch and 20 inch stages, so the planks have to suit the jacks. Louisville’s aluminum planks show what plank ratings look like, with its 12 foot P21212 rated at 500 pounds as a two-person plank, 12 inches wide and 42 pounds. Its 9 foot telescoping LP-2921-09A carries 250 pounds on a 14 inch deck, adjusts from 6 to 9 feet and stores in about half its extended length. Louisville marks both as not safe around electricity.

Placement rules apply to planks of any make. Each end must extend at least 6 inches past the centerline of its support unless cleated or hooked in place, and a platform 10 feet or shorter cannot overhang its support by more than 12 inches unless it is designed to carry weight there or guarded against access. Overlapping planks must overlap over supports by at least 12 inches unless fastened together, OSHA bars bridging one ladder jack platform to another, and a loaded platform may not deflect more than 1/60 of its span.

At our Windham and Worcester showrooms you can talk through stage widths and plank lengths with our team during a free in-person consultation.

OSHA Height, Fall Arrest and Inspection Limits on Ladder Jacks

OSHA 1926.452 caps ladder jack scaffold platforms at 20 feet high. Anyone on a ladder jack scaffold more than 10 feet above a lower level must be protected by a personal fall arrest system, which means planning the harness and connector before the stage goes up, and a competent person must inspect the scaffold for visible defects before each shift and after anything that could affect it. Work in storms or high winds is prohibited unless a competent person decides it is safe and workers have fall arrest or wind screens.

Ladder choice matters as much. Werner notes that OSHA and ANSI allow its jacks on 250 pound Type I extension ladders but recommends Type IA or Type IAA ladders, which leave more capacity for the stage, workers and material. Fiberglass models such as the Werner D7100 suit staging near service drops, and our Werner harnesses range covers the fall arrest side.

A jack or plank that fails its pre-shift check late in the week can be replaced on a Saturday morning, when both of our locations are open.

Werner D7100 Fiberglass Extension Ladders

Where Ladder Jacks and Planks Hand Over to Pump Systems and Frame Scaffolding

Ladder jack staging handles the low and middle part of a wall. Above 20 feet, or on long runs that would need bridged platforms, the work moves to pump jack systems or frame scaffolding, and every option still needs racks to haul ladders and planks to the job. Our Werner extension ladders range sets out the Type IA and IAA models to pair with jacks.

When a wall outgrows jacks, you can compare staging, racks and boxes from every maker we carry in our ladder and truck equipment brands hub.

Werner Extension Ladders

Ladder Jacks Quoted in Matched Pairs With Rated Extension Models

Matched jacks, a stage of the right width and Type IA or IAA ladders keep a ladder jacks and planks setup inside OSHA’s limits up to 20 feet. Send us your stage width and ladder series, or call 603-434-6911 or 508-754-3030, and we will quote the jacks and ladders in pairs.

Ladder Jacks and Planks FAQs

How high can ladder jacks and planks go?

OSHA 1926.452 caps ladder jack scaffold platforms at 20 feet high.

Do I need fall protection on ladder jacks?

OSHA requires a personal fall arrest system for anyone on a ladder jack scaffold more than 10 feet above a lower level.

How wide must planks be on ladder jacks?

OSHA sets a 12 inch minimum for a ladder jack scaffold platform. Werner's jacks take 14 inch and 20 inch stages.

Which ladders does Werner recommend for ladder jacks?

Type IA or Type IAA ladders, although Werner notes that OSHA and ANSI allow 250 pound Type I extension ladders.

How far must planks extend past each jack?

At least 6 inches past the centerline of the support unless cleated or hooked, and no more than 12 inches of overhang on platforms 10 feet or shorter unless designed for it.

Can job-made ladders hold ladder jacks?

No. OSHA does not allow job-made ladders to support ladder jack scaffolds.

Need help choosing the right ladder or truck equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder