Resources

Extension Ladder Sections Compared, Two-Section and Three-Section Builds by Reach, Closed Length, Weight and More

Closed length against working height, how extension size is set by the sections, overlap minimums, separable bases, Cal/OSHA length caps and which vehicles each build suits.

The number of extension ladder sections decides how long it is on the truck, how much it weighs and how much of its rated size you can climb, so choosing two or three comes down to how the ladder travels and how high the work sits. Nation Wide Ladder carries both builds from Werner and Louisville, two-section ladders in aluminum and fiberglass to 48 feet, the three-section Werner D6200-3 and 60 foot three-section models, and we help you weigh closed length, reach and overlap for your crew.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

How Extension Ladder Sections Set Size, Overlap and Working Height

Cal/OSHA defines an extension ladder as two or more sections traveling in guides or brackets, and it designates the size by the sum of the section lengths measured along the rails. Because the sections overlap when raised, the usable height is always shorter than that size. Cal/OSHA sets minimum overlaps of 36 inches on ladders up to 32 feet, 46 inches over 32 and up to 36 feet, 58 inches over 36 and up to 48 feet, and 70 inches over 48 and up to 60 feet.

Werner’s reach chart shows the effect, giving a 24 foot extension ladder an average reach of 23 feet and a 40 foot size 37 feet, based on a climber of 5 feet 7 inches with 12 inches of reach. Werner advises choosing a length 7 to 10 feet beyond the highest support point. Extra sections change those sums again, as Werner notes on its three-section D6220-3, which counts as 23 feet under ANSI yet gives the same 17 foot working height as the two-section D6220-2.

Our team checks reach and closed length together on each quote, so the number of extension ladder sections suits both the wall and the vehicle.

Two-Section Extension Ladder Builds for Everyday Reach and Roof Work

Most of the Werner and Louisville extension ladders we list are two-section designs, a base with a fly that slides up it and locks onto the rungs. Werner’s D1200-2, D1300-2, D1500-2, D6200-2 and D7100-2 run from 16 to 40 feet while the D500-2 spans 20 to 48, and on each one the base and fly separate so the base can be used alone. Louisville’s aluminum AE series and fiberglass FE3200 cover 16 to 40 feet, with fiberglass rails offered for work near power, all within our Werner extension ladders and Louisville extension ladders ranges.

The trade-off with two sections is closed length. Werner lists its 40 foot two-section models at 240 inches long closed, which sets the length of rack that will carry them, and Louisville builds its 16 foot models from two 8 foot sections. Cal/OSHA caps two-section ladders at 48 feet in metal and 72 feet in reinforced plastic, so metal ladders taller than 48 feet move to three sections.

We install truck and van racks as well as selling them, so we can size the rack to the closed length of the two-section extension model you choose.

Werner Extension Ladders

Three-Section Extension Ladder Models for Vans, Storerooms and Very Tall Walls

Three sections shorten an extension for travel. The Werner D6200-3 is a Type IA fiberglass extension model rated for 300 pounds in 16 to 32 foot sizes. Werner lists its 20 foot D6220-3 at 8 feet 4 inches closed against 10 feet 3 inches for a conventional 20 foot extension ladder, and at 40.5 pounds against 44.5 for the two-section D6220-2, while the 16 foot D6216-3 closes to 6 feet 4 inches. On the D6200-3 the base also comes away to serve as a single ladder.

At the other extreme, three sections reach heights two cannot. Cal/OSHA allows three-section metal ladders to 60 feet, and both makers build to that size. The Werner 560-3 in our Werner aluminum extension ladders range is a 60 foot Type I model whose top fly lifts off to be used on its own, and the Louisville AE1660 is a 60 foot three-section aluminum extension rated Type I for 250 pounds, with a maximum extended length of 48 feet. A third section adds a third set of locks, guides and overlap to check before each climb.

Saturday morning hours at both of our locations give a crew time to compare two-section and three-section extension ladders in person outside the working week.

Werner D6200 Fiberglass Extension Ladders

Extension Ladder Sections Across the Height Range

Section count interacts closely with the height you need. In our listings a crew can choose either build from 16 to 32 feet, while the 36 and 40 foot ladders are two-section and 60 feet means three. Our 20 ft extension ladders comparison sets two-section and three-section models side by side at one size, and Werner’s reach chart runs from 15 feet of average reach on a 16 foot extension to 49 feet on a 60 foot one.

To weigh racks and other equipment from different makers against the extension model you pick, you can compare them all in our ladder and truck equipment brands hub.

20 ft Extension Ladders

Choosing Extension Ladder Sections With Our Team

Two sections give the simplest extension for everyday reach, while three shorten the closed length for vans or stretch reach to 60 feet. Tell us the vehicle and the highest support point, and we will recommend extension ladder sections to suit both, with our own trucks delivering across New England.

Extension Ladder Sections FAQs

What is the difference between two and three extension ladder sections?

A two-section model has a base and one fly, while a three-section model divides the same size into three shorter sections that close to a shorter length.

Does a three-section extension ladder reach as high?

Werner gives its 20 foot three-section D6220-3 the same 17 foot working height as the two-section D6220-2.

How much overlap do extension ladder sections need?

Cal/OSHA sets 36 inches up to 32 feet, 46 inches over 32 and up to 36 feet, 58 inches over 36 and up to 48 feet, and 70 inches over 48 and up to 60 feet.

How long can a three-section extension ladder be?

Cal/OSHA allows three-section metal ladders up to 60 feet, the size of the Werner 560-3 and Louisville AE1660.

Can the base of an extension ladder be used alone?

On the Werner D6200-2, D6200-3 and several other Werner series, the base separates to serve as a single ladder.

How is an extension ladder's size measured?

Cal/OSHA designates it by the sum of the section lengths, which is why the reach is shorter than the size.

Need help choosing the right ladder or truck equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder