Werner Extension Ladders
Werner D7100 Extension Ladders in Type IAA Fiberglass, 16 to 40 Foot D7116-2 to D7140-2 Sizes and More
Special duty 375 pound fiberglass rails, seven lengths to 40 feet, pre-pierced V-rung and cable hook mounts, separable sections, levelers and load math for heavy climbs.
Linemen, electricians and industrial crews who climb with heavy belts, hardware and material need a nonconductive ladder with load to spare, which is the job of Werner D7100 extension ladders, rated Type IAA for 375 pounds. Nation Wide Ladder quotes the full D7100-2 run from the D7116-2 at 16 feet to the D7140-2 at 40 feet, and we help you add the V-rung, cable hooks and levelers the Werner D7100 is drilled to take.

- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Load Math Behind Werner D7100 Extension Ladders
A rating is a budget, and heavy trades spend it fast. OSHA defines the maximum intended load as every worker, tool and material on the ladder at one time, so a heavy climber with a loaded belt, a coil of wire and a fixture can pass 300 pounds before the climb starts. Type IAA, the special duty class Cal/OSHA sets at 375 pounds, leaves room for that load where a 300 pound Type IA ladder may not.
OSHA also requires a leaning ladder to hold four times its maximum intended load in testing. The Werner D7100-2 Type IAA extension ladder pairs that rating with fiberglass rails, which meet OSHA’s call for nonconductive side rails wherever the worker or ladder could touch exposed energized equipment. Werner also recommends Type IA or IAA ladders for its AC10 ladder jacks, so a D7100 suits staging near service drops. Cal/OSHA lists five classes in all, stepping down through Type IA at 300 pounds, Type I at 250, Type II at 225 and Type III at 200, which places the D7100 in the heaviest class.
Werner D7100 ladders sit at the top of the duty scale, and we can set them against our own Apprentice, Journeyman and Master ladder classes when you want a quick build-quality comparison for each crew.
Werner D7100 Sizes, Rungs and Pre-Pierced Fittings
We list seven lengths of the Werner D7100-2, the D7116-2, D7120-2, D7124-2, D7128-2, D7132-2, D7136-2 and D7140-2, running from 16 to 40 feet in 4 foot steps. Crews comparing Werner D7100 extension ladders with the lighter Aerolite will find the same 375 pound rating, with the D7100 reaching further, to 40 feet against the Aerolite’s 32. Every size uses 1.63 inch slip-resistant D-rungs set in Werner’s Alflo rung joints, with spring-loaded extruded rung locks and internal guides to move the fly smoothly.
Two details set the D7100 apart from lighter fiberglass series. The rails come pre-pierced for mounting a V-rung and cable hooks, so a crew can fit strand and pole hardware without drilling. The base and fly also separate, so the base can stand in as a single ladder for a trench, a mezzanine or a short wall while the fly stays on the truck.
Cal/OSHA caps a two-section reinforced plastic extension ladder at 72 feet, well beyond the 40 foot D7140-2, and sets a minimum overlap of 58 inches for ladders above 36 feet, so the longest D7100 sizes reach less than their label.
Saturday morning hours at both our locations make it easier to collect a D7100 or add fittings without losing a weekday.
Leveling, Inspecting and Storing Werner D7100 Extension Ladders
Werner lists both the PK80-2 and PK70-1 levelers as fitting every length of the D7100, which helps on sloped shoulders and soft ground at the pole. Werner sizes extension ladders by adding the sections together, so pick by maximum reach height rather than nominal length, and stand no higher than the fourth rung from the top. Set the base one foot out for each four feet of height, and use levelers rather than blocks or bricks, which Cal/OSHA rules out as a way to gain reach or footing.
Before each climb, and after any fall or impact, Cal/OSHA and OSHA call for a look at the ladder. Cal/OSHA asks for checks on ropes and pulleys, rung locks and guide brackets, along with the fiberglass rails for cracks, chips, splinters and heat or chemical damage. A wet ladder conducts, so dry the rails after rain. Store fiberglass out of sunlight, carry the ladder with the fly retracted, and lubricate rung lock bearings and pulleys from time to time. Werner supplies replacement labels, feet, ropes, pulleys, locks and lock flippers, and it recommends retiring rather than repairing a damaged ladder.
Our team checks leveler, V-rung and cable hook fitment against each D7100 size, so the parts on your quote match the ladder.
Werner D7100 Extension Ladders With Jacks, Racks and Fall Gear
A 375 pound fiberglass extension ladder anchors a heavier kit, from ladder jacks and planks to harnesses, lanyards and the truck rack that has to carry a 40 foot ladder safely between sites. Lighter and aluminum options sit together under every Werner extension ladder we list.
For racks, boxes and staging from other makers, browse the brands in our ladder and truck equipment brands hub.
Quotes on Werner D7100 Extension Ladders for Heavy Trades
A 375 pound rating, seven lengths to 40 feet and pre-pierced mounts for utility hardware make the D7100 a working ladder for heavy climbs. Send us the sizes and fittings or call 603-434-6911 or 508-754-3030, and we will quote Werner D7100 extension ladders for your crew, with more models in our Werner store section and on our Werner brand page.
Werner D7100 Extension Ladders FAQs
What load are Werner D7100 extension ladders rated for?
Werner rates the D7100-2 Type IAA for 375 pounds, which covers the climber, tools and materials together.
Which sizes of the Werner D7100 are available?
Seven lengths, from the D7116-2 at 16 feet to the D7140-2 at 40 feet, in 4 foot steps.
Can Werner D7100 extension ladders take a V-rung and cable hooks?
Yes. The rails come pre-pierced for mounting a V-rung and cable hooks.
Which levelers fit the Werner D7100?
Werner lists the PK80-2 and PK70-1 levelers as fitting every length of the D7100.
Can a damaged Werner D7100 ladder be repaired?
Werner recommends retiring a damaged ladder. It supplies labels, feet, ropes, pulleys and locks as replacement parts.
Need help choosing the right Werner equipment?
Talk to the team or send us your list and we will put a quote together.


