Werner Ladder Jacks
Werner AC10 Ladder Jacks in Short Body and Long Body Two-Rung and Three-Rung Models for 14 and 20 Inch Stages and More
The AC10-14-02, AC10-20-02 and AC10-20-03, stage widths, rung contact, the extension ratings Werner recommends, ordering in pairs and OSHA platform and fall rules.
Siding, trim and painting crews need a working platform along a wall without building scaffolding, and Nation Wide Ladder answers that with Werner AC10 ladder jacks, which hang a stage between two extension ladders. We quote all three AC10 models, the short body AC10-14-02 for 14 inch stages and the long body AC10-20-02 and AC10-20-03 for 20 inch stages, and we pair each Werner AC10 set with the right ladders and stage width.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Choosing Between the Three Werner AC10 Models
The three Werner AC10 models split two ways, by the stage they carry and by how many rungs they grip. The Werner AC10-14-02 short body jack is a two-rung model that supports stages up to 14 inches wide and adjusts quickly in the field. The Werner AC10-20-02 long body jack keeps the two-rung, quick-adjust design and carries stages up to 20 inches wide. The Werner AC10-20-03 three-rung jack also takes 20 inch stages, with a third rung of contact in a lightweight, sturdy body.
Start with the stage, since the jack has to suit what the crew already carries. A crew already owning 14 inch stages needs the AC10-14-02, while a 20 inch stage needs one of the long body models. Between the two long body versions, the AC10-20-02 suits frequent moves, and the AC10-20-03 spreads its grip over more rungs. Both stage widths clear the 12 inch minimum OSHA sets for a ladder jack scaffold platform, and the wider 20 inch stage gives more room to stand and set down material between the Werner AC10 jacks.
Our team checks the AC10 model against the stage width you own, so the jacks and planks on your quote work together from the first setup.
Werner AC10 Ratings and the Extension Models to Pair
Werner recommends each AC10 for use on Type IA ladders, rated up to 300 pounds, and Type IAA ladders, rated at 375 pounds. Werner also notes that OSHA and ANSI allow these jacks on 250 pound Type I extension models. The heavier ratings leave more room for the stage, the workers and their material, all of which OSHA counts toward the maximum intended load.
Each AC10 setup needs two matching jacks, two matching extension models and a stage, so plan orders in pairs. Fiberglass Type IA and IAA ladders suit staging near service drops or other electrical exposure, since OSHA requires nonconductive side rails where the worker or ladder could contact exposed energized equipment. Aluminum suits staging well away from power.
OSHA sets the bearing rule for the hardware itself. A ladder jack must bear on the side rails and rungs or on the rungs alone, and where it bears on rungs only, the bearing area has to cover at least 10 inches of each rung. Job-made ladders cannot support a ladder jack scaffold.
Over 50 years of supplying siding and painting contractors lets us pair each Werner AC10 set with extension models that suit the wall and the crew.
Setting Up Werner AC10 Ladder Jacks and Staying Within OSHA Limits
Set both ladders at the proper angle, about one foot out for every four feet of height, on firm footing, and secure them against slipping as OSHA requires. Hang each AC10 at the same rung height, then seat the stage so each end extends at least 6 inches past the center of its support unless cleated or hooked. On a stage 10 feet or shorter, OSHA limits the overhang to 12 inches unless the stage is designed to carry weight there.
OSHA caps a ladder jack platform at 20 feet high and bars bridging one platform to another. Anyone on a ladder jack scaffold more than 10 feet above a lower level must be protected by a personal fall arrest system, and a competent person must inspect the scaffold before each shift and after anything that could affect it.
Inspect the jacks for bends, cracks and worn contact surfaces and the ladders for damage before each use, checking that both Werner AC10 jacks still match, and take any bent AC10 or damaged ladder out of service. Werner recommends retiring damaged ladders rather than repairing them.
At our Windham and Worcester showrooms you can hang an AC10 on a ladder and check the fit with your stage in person.
Werner AC10 Ladder Jacks Within an Exterior Staging Plan
Ladder jacks handle the low and middle part of a wall, with harnesses for anyone above 10 feet and a rack that carries long ladders and stages. Taller walls move on to pump jacks or frame scaffolding, which come from other makers, and the wider jack range sits under Werner ladder jacks.
When the wall needs more than jacks, look over every maker in our ladder and truck equipment brands hub.
Quotes on Werner AC10 Ladder Jacks in Matched Pairs
Three models for 14 and 20 inch stages, with two-rung or three-rung grip, cover most siding and painting staging under 20 feet, as long as the ladders, stages and fall protection are planned with them. Send us your stage width and extension models, or call 603-434-6911 or 508-754-3030, and we will quote Werner AC10 ladder jacks in matched pairs, with the full Werner store range and the Werner brand page for ladders to match.
Werner AC10 Ladder Jacks FAQs
Which Werner AC10 ladder jacks take a 20 inch stage?
The long body AC10-20-02 and AC10-20-03. The short body AC10-14-02 takes stages up to 14 inches.
What ladders does Werner recommend for AC10 ladder jacks?
Werner recommends Type IA or Type IAA ladders, while noting that OSHA and ANSI allow 250 pound Type I extension ladders.
How high can Werner AC10 staging go?
OSHA caps ladder jack scaffold platforms at 20 feet.
Do I need fall protection on Werner AC10 staging?
Yes, above 10 feet. OSHA requires a personal fall arrest system for anyone on a ladder jack scaffold more than 10 feet above a lower level.
How many AC10 jacks does one setup need?
Two matching jacks on two matching ladders, plus a stage, so order in pairs.
Need help choosing the right Werner equipment?
Talk to the team or send us your list and we will put a quote together.








