Werner range
Werner Ladder Jacks in Short and Long Body, Two-Rung and Three-Rung Designs for 14 and 20 Inch Stages
The AC10-14-02, AC10-20-02 and AC10-20-03 compared on rung count and stage width, with the extension ratings Werner recommends, OSHA's 20 foot platform limit and fall arrest above 10 feet.
Werner ladder jacks turn a pair of extension ladders into a simple staging setup, with a plank spanning between them for siding, trim, gutter and painting work, and the challenge is pairing jacks, stage width and ladder rating so the whole rig stays inside OSHA's rules. Nation Wide Ladder helps you build that pairing across three models, the AC10-14-02 short body, the AC10-20-02 two-rung long body and the AC10-20-03 three-rung long body, for 14 and 20 inch stages.

- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Werner Ladder Jacks Product Lines
How Werner Ladder Jacks Turn Two Ladders Into Staging
Werner ladder jacks hook onto the rungs of extension ladders and support one end of a stage or plank, and a second ladder and jack carry the other end. The result is a working platform along a wall that is quicker to set than full scaffolding for many exterior jobs. Siding installers, painters, trim carpenters and gutter crews are the main users, along with contractors repairing older homes.
Both ladders go up at the proper angle, the jacks hook on at the same height, and the stage spans between them. Werner builds each jack around 14 inch and 20 inch stages, both wider than the 12 inch minimum OSHA sets for a ladder jack scaffold platform. Each end of the stage must reach at least 6 inches past the center of its support unless it is cleated or hooked in place, and a platform 10 feet long or shorter should not overhang its support by more than 12 inches unless designed to carry weight there. Work above about 20 feet, or a long run that would need bridging, calls for pump jack systems or frame scaffolding instead.
Over 50 years of supplying siding and painting contractors means we can tell you quickly whether a Werner ladder jack setup or a taller staging system suits the wall.
Comparing the AC10-14-02, AC10-20-02 and AC10-20-03 Werner Jacks
The Werner AC10-14-02 short body ladder jack is a two-rung model for quick field adjustment that supports stages up to 14 inches wide, a practical fit for painters and trim carpenters along a single wall.
The Werner AC10-20-02 is a two-rung long body model that supports stages up to 20 inches wide, giving more standing room on the same quick-adjust design. The Werner AC10-20-03 three-rung ladder jack is a lightweight long body model that also takes 20 inch stages, with a third rung of contact.
Every setup needs a matching pair of the same Werner model, two matching ladders and a stage, so plan orders in pairs. Werner’s descriptions note that OSHA and ANSI allow these models on 250 pound Type I extension ladders, but Werner recommends Type IA or Type IAA ladders, which leave more capacity for the stage, the workers and their gear. All three Werner models adjust quickly in the field, which helps when leveling the stage between ladders set on uneven ground.
Our team checks the model, stage width and ladders together, so the Werner ladder jacks on your quote arrive as a working pair.
Where Werner Jacks Sit Among Staging Options
Ladder jack staging covers the low and middle part of an exterior wall, and it works best when a crew knows where it stops. Above about 20 feet, or on long runs that would need bridging, pump jack systems and frame scaffolding take over, and those come from other manufacturers. Siding crews also lean on brakes for bending trim on site, and every staging setup needs a way to haul planks, poles and long extension ladders to the job. Seeing jacks as one step in that progression makes it easier to choose the right system for each wall.
When a wall outgrows Werner jacks, you can compare every manufacturer we carry in our ladder and truck equipment brands hub.
Werner Ratings and OSHA Scaffold Rules for Jack Setups
Werner recommends pairing each ladder jack with a Type IA extension ladder, rated up to 300 pounds, or a Type IAA ladder, rated at 375 pounds. That reflects how load works on a jack setup, where the plank, the workers and their material all bear on the ladders.
OSHA 1926.452(k) caps ladder jack scaffold platforms at 20 feet high. Each ladder supporting Werner jacks has to meet OSHA’s rules in Subpart X, and job-made ladders cannot be used. Each jack must bear on the side rails and rungs or on the rungs alone, and where it bears on rungs only, the bearing area has to be at least 10 inches on each rung. The ladders must be placed, fastened or fitted to prevent slipping, and platforms cannot be bridged one to another.
OSHA 1926.451 adds two rules. Anyone on a ladder jack scaffold more than 10 feet above a lower level has to wear a personal fall arrest system, and a competent person must inspect the scaffold for visible defects before each shift and after anything that could affect its integrity.
At our Windham and Worcester showrooms you can see Werner jacks hung on a ladder and talk through the OSHA limits in person.
Choosing Werner Ladder Jacks With Matching Extension Ladders
Start with the stage. A 14 inch stage pairs with the AC10-14-02, while a 20 inch stage needs one of the long body Werner models. Choose between the two-rung and three-rung models based on how often you adjust height and how much contact you want on the rungs. Then pick Type IA or Type IAA ladders from our Werner extension ladders range, buying in matching pairs so both ends sit at the same geometry.
The fiberglass Werner D6200-2 (Type IA) and D7100-2 (Type IAA) suit staging near service drops or other electrical exposure, while the aluminum D1500-2 (Type IA) and D500-2 (Type IAA) suit general siding and painting work. The Werner D1200-2 and D1300-2 fall short of the Type IA rating Werner recommends for its jacks, so leave them for ordinary use.
Plan fall protection at the same time. Above 10 feet each worker on the stage needs a harness and connector tied to an anchorage that does not rely on the ladders or the stage, since OSHA requires fall arrest anchorages to be independent of any anchorage supporting a platform.
Send us the stage width and ladders as a list, or call 603-434-6911 or 508-754-3030, and we will quote matched Werner ladder jacks.
Setting Up and Inspecting Werner Jacks Before Each Shift
Set both ladders at the proper angle, roughly one foot out for every four feet of height, and secure their feet before hanging the Werner jacks. Check that each jack seats fully on the rungs and that the stage sits squarely in both jacks before stepping onto it. Inspect each jack and ladder before each use, and take any bent jack or damaged ladder out of service, since Werner does not recommend repairing damaged ladders. Where a jack bears on rungs only, confirm at least 10 inches of bearing on each rung, as OSHA requires, and plan the work so the platform stays at or under the 20 foot limit. Safety labels must stay legible under OSHA rules, and Werner supplies replacements through its customer care team.
Werner also runs ladder safety training, including its Climbing Pro Ladder Safety 101 and Ladder Core courses on setup, selection and inspection, which suit crews bringing on new hires to staging work.
A jack that fails inspection late in the week can be replaced on a Saturday morning, when both of our locations are open.
Ordering Werner Ladder Jacks in Matched Pairs
Compare models in our ladder jack category or return to the Werner brand overview. We quote Werner ladder jacks in matched pairs, and our own trucks deliver them door to door across New England.
Werner Ladder Jacks FAQs
Which ladders does Werner recommend for Werner ladder jacks?
Werner recommends Type IA ladders rated up to 300 pounds or Type IAA ladders rated at 375 pounds.
How high can a platform on Werner jacks be?
OSHA 1926.452(k) limits ladder jack scaffold platforms to 20 feet high.
Which Werner ladder jack fits a 20 inch stage?
The Werner AC10-20-02 and AC10-20-03 long body models both support stages up to 20 inches wide. The AC10-14-02 is for stages up to 14 inches.
Can I use homemade ladders with Werner jacks?
No. OSHA prohibits job-made ladders from supporting ladder jack scaffolds.
Do I need fall protection on Werner ladder jacks?
OSHA 1926.451 requires a personal fall arrest system for anyone on a ladder jack scaffold more than 10 feet above a lower level.
Need help choosing the right Werner equipment?
Talk to the team or send us your list and we will put a quote together.





