Werner Extension Ladders
Werner Aluminum Extension Ladders, from Medium Duty Type II to Type IAA, in Two and Three Section Models and More
Duty ratings from 225 to 375 pounds, reach from 16 to 60 feet, D-rung and lock hardware, levelers, care and the electrical limits that come with metal rails.
Werner aluminum extension ladders answer a daily problem for painters, maintenance crews and homeowners, moving a tall ladder many times a day without wearing out the person carrying it. Nation Wide Ladder has spent over 50 years matching contractors and homeowners to the right ladder, and we carry the Werner D1200-2, D1300-2, D1500-2 and D500-2 two-section series plus the three-section Werner 560-3, rated from 225 to 375 pounds in lengths from 16 to 60 feet.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Werner Aluminum Ladders Against Fiberglass for Everyday Work
Werner asks two questions when you pick a ladder material, how often the ladder moves and whether electricity is anywhere near the work. Aluminum is light and easy to carry, so Werner suggests aluminum for painting, household tasks, maintenance work and quick jobs where the extension ladder shifts along a wall again and again. Aluminum also resists denting, shattering, rust and corrosion, and Werner designs and tests it for extreme temperatures.
Conductivity sets the limit. Aluminum conducts electricity, and Werner states plainly that aluminum is not for use around electrical hazards. OSHA 1926.1053 requires nonconductive side rails anywhere a worker or ladder might touch exposed energized equipment, and Cal/OSHA warns against metal ladders for work near energized conductors, which includes the overhead service lines running to a building.
If your job list is exterior painting, gutter cleaning, window work, siding repair or general upkeep away from wiring, Werner aluminum extension ladders save effort on every move. Crews who also take on electrical, utility or industrial work will want Werner fiberglass extension ladders for those jobs.
Bring your job list to a free consultation at our Windham NH or Worcester MA showroom and we will help you weigh Werner aluminum against fiberglass for it.
Werner Aluminum Extension Ladders by Load Rating, from the Entry Type II D1200-2 to the Three Section 560-3
The range climbs in clear steps. The Werner D1200-2 is the entry point at Type II, rated for 225 pounds, and the Werner D1300-2 moves up to Type I at 250 pounds. Werner describes both as medium-duty aluminum ladders, sold in 16, 20, 24, 28, 32, 36 and 40 foot sizes.
The Werner D1500-2 Type IA aluminum extension ladder is rated for 300 pounds and adds extra heavy duty I-beam rails plus a rail-on-rail system that widens the fly section, again from 16 to 40 feet. For the heaviest daily use, the Werner D500-2 carries a Type IAA, 375 pound rating in its 20, 24, 28 and 32 foot sizes, while its 36, 40, 44 and 48 foot models are rated Type IA at 300 pounds, a split worth checking when you order a long extension ladder for a crew that climbs loaded.
The Werner 560-3 is a three-section, 60 foot aluminum extension ladder rated Type I at 250 pounds on extra heavy duty I-beam rails, raised with a heavy duty rope and double pulley. Its top fly comes off as a straight ladder while the base and middle sections carry on as a 40 foot extension ladder, so one purchase covers more reach than the two-section models in our Werner extension ladder lineup.
Our Apprentice, Journeyman and Master ladder classes give you a second way to compare build quality across these Werner series before you order.
Rungs, Locks and Load Limits on Werner Aluminum Extension Ladders
The four two-section Werner series share the same core hardware. Rungs are 1.75 inch slip-resistant D-rungs, joined to the rails with Werner Alflo rung joints for stability. Spring-loaded heavy duty extruded rung locks hold the fly, internal guides help it slide smoothly, and the base and fly separate so the base can work alone as a straight ladder on shorter climbs.
The duty rating is the total weight the extension ladder is designed to carry. Cal/OSHA lists the scale as Type III at 200 pounds, Type II at 225, Type I at 250, Type IA at 300 and Type IAA at 375. OSHA defines that maximum intended load as every employee, tool, piece of equipment and material on the ladder at once, so a painter with a full belt and a loaded bucket can pass a Type II limit quickly. OSHA also requires a leaning portable ladder to hold four times that load in testing, or 3.3 times for the extra-heavy-duty Type IA metal class.
Site rules apply too. Rungs must be parallel, level and spaced 10 to 14 inches apart, two ladders may not be joined end to end unless built for it, and nothing may be carried up that could throw the climber off balance.
Tell our team what each climber carries and we will check the duty rating against that load before you order.
Sizing, Leveling and Care for a Werner Aluminum Extension Ladder
Werner sizes an extension ladder by the combined length of its sections, with a tolerance of 3 inches per section, and that figure ignores the overlap once the fly is raised. A 32 foot extension ladder therefore stops short of 32 feet of reach, which is why Werner recommends shopping by maximum reach height. Keep your feet at or under the fourth rung from the top, and for roof access choose a length whose rails reach 3 feet or more beyond the roof edge, as OSHA requires. Set the base out about 1 foot for every 4 feet of height to the support point.
On sloping ground, the Werner FAQ matches PK80-2 leg levelers to the D500 series and PK70-1 levelers to the D1300, while OSHA allows a ladder on uneven ground only when it is secured against displacement.
Check the rails, rungs, locks, hardware and feet before every climb. Werner sells replacement kits for labels, feet, ropes, pulleys, locks and lock flippers, but not individual sections, and does not recommend repairing a damaged ladder, so tag it out of service as OSHA requires and replace it. Ladder jacks, stabilizers and covers sit in our Werner ladder parts and accessories range.
Our own trucks deliver door to door across New England, so a 40 or 60 foot Werner aluminum extension ladder arrives at your site ready to climb.
How Werner Aluminum Ladders Fit a Working Contractor Truck
On a working truck an aluminum extension ladder usually travels with stepladders, tool storage and the rack that carries it, and the ladder length you choose decides how much rack the truck needs. Matching those pieces is easier when you can compare the makers side by side.
You can line up every manufacturer we carry in our ladder and truck equipment brands hub.
Ordering Werner Aluminum Extension Ladders
Light rails for frequent moves, ratings from 225 to 375 pounds and reach up to 60 feet make the Werner aluminum range a practical fit for crews working away from power. Send us a list with the reach, rating and number of ladders you need, or call 603-434-6911 in NH or 508-754-3030 in MA, and we will quote Werner aluminum extension ladders to suit. Compare sizes in our aluminum extension ladder category or visit the Werner brand overview.
Werner Aluminum Extension Ladders FAQs
Can I use Werner aluminum extension ladders near power lines?
No. Aluminum conducts electricity, and OSHA demands nonconductive rails anywhere the ladder or worker might touch exposed live equipment. Choose a Werner fiberglass extension ladder for that work.
Which Werner aluminum extension ladder is rated for 375 pounds?
The Werner D500-2, rated Type IAA at 375 pounds in 20 to 32 foot sizes. Its 36 to 48 foot models are rated Type IA at 300 pounds.
How does the Werner 560-3 aluminum extension ladder work as two ladders?
The top fly lifts off to serve as a straight ladder, and the base and middle sections keep working as a 40 foot Werner extension ladder.
What is the lightest duty Werner aluminum extension ladder?
The Werner D1200-2 at Type II, rated for 225 pounds. The Werner D1300-2 steps up to Type I at 250 pounds in the same 16 to 40 foot sizes.
Which levelers fit Werner aluminum extension ladders?
The Werner FAQ lists PK80-2 levelers for the D500 series and PK70-1 levelers for the D1300.
Can a bent Werner aluminum ladder be repaired?
Werner does not recommend repairing damaged ladders or sell individual sections, though labels, feet, ropes, pulleys and locks can be replaced.
Need help choosing the right Werner equipment?
Talk to the team or send us your list and we will put a quote together.











