Resources
Ladder Stabilizers and Levelers, From Standoff Arms and V-Bars to Leg Levelers, Pole Straps and More
When a standoff earns its place, span and standoff sizes from Werner and Louisville, leg levelers for slopes and steps, roof and pole straps, and the OSHA footing rules that apply either way.
Ladder stabilizers hold the top of an extension ladder off gutters, glass and siding while levelers square the feet on a slope, and the challenge is knowing which problem a job has before buying either. Nation Wide Ladder carries both from Werner, Louisville and LeveLok, including standoff stabilizers, V-bars for poles and corners, leg levelers and LeveLok roof and pole straps, and our team matches each one to the ladders you run.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
When Ladder Stabilizers Earn a Place at the Top of the Rails
An extension ladder leaned straight on a building rests its rails on whatever is there, which may be a gutter, a window frame or soft vinyl siding. OSHA requires the top of a ladder that is not self-supporting to have both rails supported equally unless it has a single support attachment, and Cal/OSHA wants the top resting evenly on a flat, firm surface that has been tested for strength. Ladder stabilizers answer both points by clamping to the upper section and bearing on the wall either side of the obstacle on two padded arms, so the gutter or glass carries nothing.
Painters, gutter and siding crews and window cleaners use them for that reason, and painters also gain room to work on the fascia or trim behind the rails. Stabilizers are made for extension ladders such as Werner extension ladders, and Louisville lists its LP-2200-00 for most extension and single ladders with rails up to 3.5 by 1 3/4 inches. Once one is fitted, the support point moves to where the arms touch the wall, which is where the 4 to 1 setback is measured from.
Our team checks rail size and series before we quote, so the stabilizers you order clamp to the ladders already on your truck.
Comparing Werner and Louisville Ladder Stabilizers by Span and Standoff
Span decides what a stabilizer can straddle, and standoff decides how far the rails sit from the wall. The Werner AC78 QuickClick spans 44 inches, holds the ladder 10 inches out and fits without tools through a spring-loaded latch, with a paint can hook included. The Werner 97P Adjustable True Grip adjusts to 49, 57 or 65 inches, wide enough for a double window, with a standoff of 12 or 29.5 inches for deep eaves. Louisville’s LP-2200-00 sets the ladder 12 inches off the wall on a 45 inch span, mounts with two U-bolts and uses replaceable rubber tips.
For poles and outside corners, a V-bar does a similar job. Louisville makes the PK-E04A for its fiberglass extension ladders from 16 to 28 feet, and the PK-E03 with hooks in versions for 16 to 28 and 32 to 40 feet. Compare them in our Werner ladder stabilizers and Louisville ladder accessories ranges. None of these accessories raises the duty rating, since OSHA counts the climber, tools and anything hung from the rails toward the maximum intended load.
At our Windham and Worcester showrooms you can see how each of these stabilizers mounts during a free in-person consultation.
Levelers, Straps and Footing Rules That Work Alongside Ladder Stabilizers
A stabilizer steadies the top, while the feet need their own answer. OSHA allows ladders only on stable, level surfaces unless they are secured, and Cal/OSHA says to use leg levelers or mudsills where one foot sits low rather than propping it on bricks or blocks. Werner lists its PK80-2 leg levelers for all lengths of the D6200, D7100, D1200, D1300 and D500 series, among others. The LeveLok LL-STB-2QC leaves two quick connect bases on the rails and snaps one leveler on when needed, extending in 3/16 inch steps up to 10 inches, and LeveLok approves it up to a Type IAA, 375 pound rating on rails 1/2 inch thick or less.
Straps cover cases a leveler cannot. LeveLok’s L2R roof tie-down straps hook over a nail or screw set in the roof to limit side-to-side slip at the eave, and its LSS-150 strap wraps a utility pole and, installed properly, limits side rail movement to 3 inches. Cal/OSHA lists leg levelers and stand-off accessories among the items to check before each use, so inspect pads, arms, leg locks and webbing along with the ladder.
Our regular weekly deliveries from New Hampshire to Maine let crews there add levelers or stabilizers to a ladder order on a set schedule.
Ladder Stabilizers in a Wider Exterior Equipment Plan
Stabilizers and levelers are one part of an exterior setup that also takes in the ladder itself, the rack that carries it and, at the eave, harnesses and anchors. Settling them together keeps rail sizes, ratings and fittings consistent across a crew’s ladders, and our {a(‘werner/ladder-parts-accessories’, ‘Werner ladder accessories’)} range adds Lock-In buckets and the AC18MT platform for longer stints aloft.
If racks, staging or anchors from other makers are on your list, you can line them up in our ladder and truck equipment brands hub.
Quotes on Ladder Stabilizers and Levelers for Your Ladders
A standoff for the top and a leveler for the feet solve different problems, and many exterior crews need both. Send us your ladder series and the buildings you work on, or call 603-434-6911 in New Hampshire or 508-754-3030 in Massachusetts, and we will quote ladder stabilizers and levelers to fit.
Ladder Stabilizers FAQs
When do I need ladder stabilizers?
When the top of an extension ladder would otherwise rest on a gutter, window or other surface that cannot carry it, or when you need room to work behind the rails.
How far do ladder stabilizers hold a ladder off the wall?
The Werner AC78 gives 10 inches, the Werner 97P 12 or 29.5 inches and the Louisville LP-2200-00 12 inches.
Do ladder stabilizers fit step ladders?
No. They are made for extension ladders, and Louisville also lists its LP-2200-00 for single ladders.
What is the difference between a stabilizer and a leveler?
A stabilizer supports the top of the ladder against the wall, while a leveler lengthens one leg so the feet sit level on a slope or step.
Which ladders take the LeveLok leveler?
LeveLok approves the LL-STB-2QC for extension, articulating, straight, combination, sectional and step ladders up to Type IAA, with rails 1/2 inch thick or less.
Do ladder stabilizers change the duty rating?
No. OSHA counts the climber, tools and anything hanging from the ladder toward its maximum intended load.
Need help choosing the right ladder or truck equipment?
Talk to the team or send us your list and we will put a quote together.








