Ladders by Height
20 ft Extension Ladders in Aluminum, Fiberglass and Lightweight Aerolite Builds, Type II to Type IAA and More
Reach for split-levels, raised ranches and cape roof edges, the full run of duty ratings at this size, Aerolite weight savings and Werner and Louisville series compared.
Split-level eaves, cape roof edges and shopfront signs are typical jobs for 20 ft extension ladders, and Nation Wide Ladder prices them from both Werner and Louisville. At this height you can choose aluminum, fiberglass or Werner's lightweight Aerolite, and every duty rating from Type II to Type IAA, so we compare the AE2200, AE3200, AE4200 and FE3200 with the D500-2, D1200-2, D1300-2, D1500-2, D6200-2, D6200-3, D7100-2 and B7100-2.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
How High 20 ft Extension Ladders Reach on Split-Levels and Capes
The 20 is the step up for houses that sit a little taller than a ranch. Werner’s reach guide gives a 20 ft extension ladder an average reach of 19 feet, and Louisville lists 19 feet 10 inches of maximum reach for its 20 ft models, both for a climber of 5 feet 7 inches reaching 12 inches overhead. Louisville also gives a maximum extended length of 17 feet, since two 10 foot sections overlap when the fly goes up. That range suits the eaves of a split-level or raised ranch, the low edge of a cape roof and signs or lights over a shop door.
Werner’s sizing rule is to buy an extension ladder 7 to 10 feet longer than the highest point it leans on, and to stand no higher than four rungs from the top. Measured that way, a 20 sits between the single-storey 16 and the 24 that most two-storey gutters need. If you climb onto a flat roof or deck, OSHA wants the rails running at least 3 feet past the landing, which is easy to forget when you pick a 20 by the gutter height alone.
Our showrooms in Windham, New Hampshire and Worcester, Massachusetts offer free in-person consultations, so you can stand a 20 ft model up and check it against your house measurements first.
Every Duty Rating in 20 ft Extension Ladders, From Type II to IAA
Every duty rating is on offer at 20 across the two brands, and this is the first size where Werner adds an aluminum Type IAA model. In aluminum, Louisville offers the AE4220 at Type II for 225 pounds, the AE3220 at Type I for 250 and the AE2220 at Type IA for 300, while Werner lines up the D1220-2, D1320-2 and D1520-2 at the same three ratings. Werner adds the D520-2, an aluminum 20 rated Type IAA for 375 pounds, which is the heaviest aluminum rating at this size from either maker.
In fiberglass, Louisville’s FE3220 is rated Type IA, with a MAXLOCK polymer rung lock and steel swivel shoes, and Werner offers the Type IA D6220-2, the three-section D6220-3 and the Type IAA D7120-2. The D7100-2 rails carry pre-pierced holes for a V-rung and cable hooks, so a 20 can be set up for strand work. Choose the rating by adding the climber, clothing, tools and material together, since every one of those counts toward the load on the ladder. Louisville also fits its QuickLatch to the FE3200 and AE4200 extension ladders, latching the fly and base together for climbing and for transport.
Send us the weight you expect to put on a 20 ft ladder and the material you prefer, and we will turn it into a written quote across both brands.
Lighter 20 ft Extension Ladders for Crews Who Carry Them All Day
Weight is the other half of the choice at this size. Louisville lists its aluminum 20 ft models at 32 to 37 pounds and the fiberglass FE3220 at 42 pounds, with a closed height of about 124 to 125.5 inches. Werner’s answer for crews who want a Type IAA rating without the usual heft is the Aerolite B7120-2, which Werner describes as 25 percent lighter than a standard 375 pound ladder. It uses a BOXLOK box rail to cut bounce and side sway and wide Traction-Tred tri-rungs to stand on.
The Aerolite range starts at this height, so the 20 is the shortest size where you can have a lightweight fiberglass Type IAA from Werner. It comes here as the plain B7120-2, since the CL versions with a V-rung and leveler system start at 24 ft, so crews who want those extras on their Aerolite extension ladders move up a size. For lighter household jobs, a Type II or Type I aluminum 20 is the easier carry, while fiberglass makes sense around service entrances and outdoor lighting because the rails are nonconductive.
Our own trucks deliver door to door across New England, so a full 20 ft extension ladder order arrives at the yard ready to load onto your racks.
20 ft Ladders Within a Full Set of Access Equipment
A 20 often works beside levelers on sloping lawns, a stabilizer that holds the ladder off the gutter, and a step ladder for the inside of the job. Every size from 2 ft step ladders to 40 ft extensions is laid out in our ladders by height section, and the Werner 20 ft models and Louisville 20 ft models each have their own breakdown.
When the plan also takes in racks, boxes or scaffolding, our ladder and truck equipment brands hub lets you compare the other makers we carry.
Ordering 20 ft Extension Ladders From Our New Hampshire and Massachusetts Showrooms
At 20 the choice is wide, from a light Type II for occasional use to an Aerolite Type IAA for daily work, so it pays to decide by the load you carry and the hours you climb. Call 603-434-6911 or 508-754-3030 and we will quote 20 ft extension ladders from both makers by load, material and weight, including the Louisville AE3200 series as a Type I aluminum choice.
20 Ft Extension Ladders FAQs
What can I reach with a 20 ft extension ladder?
Werner gives an average reach of 19 feet and Louisville a maximum reach of 19 feet 10 inches, both for a 5 foot 7 inch climber with 12 inches of reach.
Is there an aluminum 20 ft extension ladder rated Type IAA?
Yes. The Werner D520-2 is an aluminum 20 rated Type IAA for 375 pounds.
Which is the lightest Type IAA 20 ft model?
Werner describes its Aerolite B7120-2 as 25 percent lighter than a standard 375 pound rated extension ladder.
How much does a Louisville 20 ft extension ladder weigh?
Louisville lists 32 to 37 pounds for its aluminum 20 ft models and 42 pounds for the fiberglass FE3220.
What is the maximum extended length of a 20 ft extension ladder?
Louisville gives 17 feet for its 20 ft models, because the two 10 foot sections overlap when extended.
Does the Werner D7120-2 take a V-rung?
Its rails have pre-pierced holes for mounting a V-rung and cable hooks.
Need help choosing the right ladder equipment?
Talk to the team or send us your list and we will put a quote together.








