Werner Extension Ladders
Werner D1200 and D1300 Extension Ladders in Type II and Type I Aluminum, 16 to 40 Foot Sizes and More
Medium-duty 225 pound and heavy-duty 250 pound aluminum ratings, 1.75 inch D-rungs, separable sections, leveler fitment and the electrical limits of metal rails.
Homeowners, painters, gutter crews and property managers who climb to a roofline a few times a season, well away from live wiring, are well served by Werner D1200 and D1300 extension ladders in aluminum. The challenge is matching a lighter rating to the person and load, and Nation Wide Ladder helps by setting the Type II D1200-2 at 225 pounds against the Type I D1300-2 at 250 pounds, each offered from 16 to 40 feet, so we quote the Werner series that suits who will climb it.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Werner D1200 and D1300 Extension Ladders for Seasonal and Light Trade Work
Werner calls both series medium-duty aluminum designs, and the difference that matters on paper is the duty rating. The Werner D1200-2 Type II extension ladder carries a 225 pound working load, the medium-duty class on the Cal/OSHA scale. The Werner D1300-2 Type I extension ladder steps up to 250 pounds, which Cal/OSHA labels heavy-duty. Both come in 16, 20, 24, 28, 32, 36 and 40 foot sizes, from the D1216-2 and D1316-2 to the D1240-2 and D1340-2. Each D1200 size has a matching Type I twin at the same length, so the choice rests on rating rather than reach.
That makes the pair a fit for jobs where a heavier fiberglass ladder would be more than the work asks for, such as cleaning gutters, washing windows, touching up trim or checking a roof after a storm. A D1200 suits a lighter climber with a modest tool load, while the Type I model leaves more room for a heavier worker or a full bucket. When the climber, belt and material add up past 250 pounds, the Werner range moves on to Type IA and IAA models.
Over 50 years of supplying homeowners as well as contractors means we can size a Werner D1200 or D1300 to the person who will actually climb it.
Werner D1300 and D1200 Aluminum Rails, D-Rungs and Rung Locks
The Werner D1200 shares one build with its Type I sibling. Each rung is a 1.75 inch slip-resistant D-rung fixed with Werner’s Alflo rung joints, and spring-loaded extruded rung locks hold the fly in place once it is raised. Internal guides help the fly travel smoothly, and the base and fly separate so the base can work as a straight ladder on a porch or a short wall. OSHA requires metal rungs on portable ladders to be corrugated, knurled, dimpled, coated or otherwise treated against slipping, which is the role of the slip-resistant D-rung profile.
Aluminum also sets limits. Cal/OSHA says metal ladders should never be used for work on or around exposed electrical parts, asks for caution labels warning against use near electrical equipment, and advises against handling a metal ladder near power lines. OSHA requires nonconductive side rails wherever a worker or ladder could contact exposed energized equipment, so electrical work belongs on fiberglass. Wind is another factor, as Cal/OSHA warns against setting up lightweight metal models in high wind.
At our Windham and Worcester showrooms you can lift a D1200 and a D1300 and compare them in person, with a free consultation before you buy.
Sizing and Leveling Werner D1200 and D1300 Extension Ladders
Werner measures an extension ladder as the total of its rail sections, so reach falls short of the label once the sections overlap. Choose by maximum reach height, plan to stand no higher than the fourth rung from the top, and let the rails run at least 3 feet past a roof edge you plan to step onto. At setup, put the base one foot out for every four feet of height to the support point. Cal/OSHA also sets minimum overlaps of 36 inches on two-section ladders up to 32 feet, 46 inches above 32 and up to 36 feet, and 58 inches above 36 feet, so a D1240-2 reaches noticeably less than 40 feet.
For uneven ground, Werner lists the PK80-2 leveler for every length of both the D1200 and the D1300, while its PK70-1 leveler covers the D1300 only. Siding and painting crews should also check ratings before hanging ladder jacks, since Werner recommends a Type IA or IAA extension ladder under its AC10 jacks, while noting that OSHA and ANSI allow a 250 pound Type I model. Cal/OSHA lists dented rungs or rails, sharp edges, corrosion and bends as reasons to pull a metal ladder from service.
Our team checks leveler and jack fitment against the series you choose, so the parts on your quote suit the Werner D1200 or D1300 you run.
Werner D1200 and D1300 Extension Ladders in a Home or Small Crew Kit
A homeowner or small painting crew usually pairs an aluminum extension ladder with a step ladder for indoor work, a stabilizer to clear gutters and a rack or storage hooks for the garage or truck. Other materials and heavier ratings sit in the full Werner extension ladder lineup.
If you are planning storage or a vehicle rack as well, compare the makers we carry in our ladder and truck equipment brands hub.
Ordering Aluminum Werner D1200 Extension Models From Our Team
A 225 pound Type II rating, a 250 pound Type I rating and seven shared lengths make the choice a matter of who climbs and how high. Call 603-434-6911 in New Hampshire or 508-754-3030 in Massachusetts, or send a list, and we will quote Werner D1200 and D1300 extension ladders for your home or crew, with more choices in our Werner store section and on the Werner brand page.
Werner D1200 and D1300 Extension Ladders FAQs
What is the difference between Werner D1200 and D1300 extension ladders?
The D1200-2 is rated Type II for 225 pounds and the D1300-2 is rated Type I for 250 pounds. Both are aluminum and come in 16 to 40 foot sizes.
Can I use a Werner D1200 or D1300 near electrical wiring?
No. Cal/OSHA says metal ladders should never be used on or around exposed electrical parts, so choose a fiberglass Werner ladder for that work.
Which levelers fit a Werner D1200 extension ladder?
Werner lists the PK80-2 for all lengths of both series and the PK70-1 for the D1300 only.
Can Werner D1200 or D1300 extension ladders hold ladder jacks?
Werner recommends Type IA or IAA ladders for its AC10 jacks, while OSHA and ANSI allow 250 pound Type I ladders such as the D1300. The Type II D1200 sits beneath both.
Does the base of a Werner D1300 separate?
Yes. On both the D1200-2 and D1300-2 the base and fly separate, so the base can be used as a single ladder.
Need help choosing the right Werner equipment?
Talk to the team or send us your list and we will put a quote together.






