Resources

Cut Resistant Gloves and ANSI Cut Levels A1 to A9, With Test Loads, EN 388 Codes, Coatings, Liners and More

The gram loads behind each ANSI/ISEA 105 cut level, what A1 to A9 are meant to stop, puncture and abrasion grades, European EN 388 codes, and choosing a shell and coating for cold, wet or fine work.

Sheet metal, trim coil, glass and blades all call for cut resistant gloves, and the ANSI cut level on the label is how you match a pair to the hazard, which Nation Wide Ladder helps crews do when we quote Global Glove pairs. We cover the nine ANSI/ISEA 105 cut levels and the loads behind them, puncture and abrasion grades, European EN 388 codes, insulated and thin knit shells, rubber and polyurethane coatings and how OSHA expects hand protection to be chosen.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

How ANSI Rates Cut Resistant Gloves From A1 to A9

ANSI/ISEA 105 sorts cut resistant gloves into nine levels by the weight, in grams-force, needed to cut through the material with 20 mm of blade travel. The International Safety Equipment Association (ISEA) lists A1 at 200, A2 at 500, A3 at 1,000, A4 at 1,500, A5 at 2,200, A6 at 3,000, A7 at 4,000, A8 at 5,000 and A9 at 6,000. Each step means a cut resistant knit or coating took a heavier load before the blade cut through.

ISEA groups the levels by the injury they are meant to prevent. Levels A1 to A3 protect against scrapes, A4 to A6 against cuts that would need stitches, and A7 to A9 against brutal or extreme injuries. Most trade work with sharp edges, such as handling cut trim coil, flashing or glass, sits in the middle of that range. The current edition is ANSI/ISEA 105-2024, which adds new marking rules so cut, puncture and abrasion levels show on the product. Many pairs on the market, including the Global Glove models we list, are rated to the 2016 edition, which used the ASTM F2992-15 test on a TDM-100 machine and the same A1 to A9 scale.

Our team helps you select a cut level for each task by asking what the sharpest edge on the job is and how often hands meet it.

Reading Cut Resistant Gloves Labels for Puncture, Abrasion and EN 388

The cut level is one of several numbers on a label. ISEA’s 105 standard also grades puncture resistance by the force needed to push a sharp probe through the material, and abrasion resistance by the number of abrasion cycles it survives. ISEA also notes that not every puncture resistant glove protects against needle sticks. Global Glove prints all three on each pair we list. The Samurai Glove CR318INT is rated A5 for cut at 2,264 grams and level 5 for puncture, the Ice Gripster 380INT A3 at 1,219 grams, and the thin PUG-921 A4 at 1,769 grams with level 5 abrasion.

Gloves sold in Europe add an EN 388 code, a string read left to right for abrasion, blade cut, tear and puncture, with a final letter for the ISO cut test. An X means that property was not tested or the method does not apply, so the CR318INT reads 3X43E. Insulated pairs may add EN 511 cold codes, and EN 407 adds heat codes where tested. Compare the ANSI cut level first, then use the other figures to choose between pairs with similar cut ratings. Our Global Glove cut resistant work gloves page lists the full ratings for each model.

Call 603-434-6911 in New Hampshire or 508-754-3030 in Massachusetts with the cut level your site requires, and we will quote cut resistant gloves rated to it.

Global Glove Work Gloves

Choosing Cut Resistant Gloves by Task, Season and Dexterity

OSHA 29 CFR 1910.138 requires employers to select hand protection when hands face severe cuts, lacerations, abrasions, punctures or temperature extremes, and to base the choice on how the glove performs against the task, the conditions, how long it is worn and the hazards present. A cut rating is only part of that decision, since a glove too bulky for the task tends to come off.

Cold, wet work points to insulated cut resistant gloves. The Ice Gripster 380INT pairs a polyester shell with an acrylic terry liner under a double rubber coating that is liquid resistant, and the CR318INT uses a water repellent Tuffalene shell for its higher A5 cut level, with touch screen fingertips on both. Fine work points to thin cut resistant knits. The 18 gauge PUG-118 and 21 gauge PUG-921 have polyurethane palms for close feel, are listed as anti-static for ESD protected areas, and use materials that comply with FDA food contact rules. The wider Global Glove safety gear range covers the same crews with helmets and knee pads, and our Global Glove helmets page covers head protection.

Our own trucks deliver door to door across New England, so a season’s supply of pairs can arrive with the rest of a crew’s order.

Global Glove

Cut Resistant Gloves Around Brakes, Coil and Ladders

Many hand cuts happen at the trim station rather than on the wall, where freshly cut coil comes off a TrimCutter and coil dispenser or an Alum-A-Brake, and again when ladders and stock come off a truck rack.

To compare the brake, ladder and rack makers that crews handle every day, browse our ladder and truck equipment brands hub.

Van Mark TrimCutter and Coil Dispenser

Cut Resistant Gloves Matched to Your Crew’s Hazards

Nation Wide Ladder has supplied contractors for over 50 years, and we quote cut resistant gloves by model, size and cut level, matched to the edges your crew handles and the season they work in.

Cut Resistant Gloves FAQs

What do ANSI cut levels on cut resistant gloves mean?

They grade how much load, in grams-force, it takes to cut through the glove material with 20 mm of blade travel, from A1 at 200 to A9 at 6,000.

What cut level do I need for sheet metal?

ISEA describes A4 to A6 as protection against cuts that would need stitches. Match the level to the sharpest edge on the job.

Is a higher cut level always better?

Not for every task. OSHA 1910.138 asks employers to weigh the task, conditions and duration, and a bulkier high-level glove can cost dexterity.

Are puncture resistant and cut resistant ratings the same?

No. ANSI/ISEA 105 grades cut and puncture separately, and ISEA notes that not every puncture resistant glove protects against needle sticks.

What does an X mean in an EN 388 code?

An X means that property was not tested or the test method does not apply to that glove.

Which cut resistant gloves suit winter work?

Insulated models such as the Global Glove Ice Gripster 380INT and Samurai Glove CR318INT, which add acrylic terry liners and EN 511 cold ratings.

Are gloves rated to ANSI/ISEA 105-2016 still valid?

They use the same A1 to A9 cut scale. The 2024 edition adds new marking requirements for cut, puncture and abrasion.

Need help choosing the right ladder or truck equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder