Resources

Ladder Levelers for Uneven Ground, Quick Connect Leg Kits, Werner and Louisville Fitments, Duty Ratings, Setup and More

OSHA's level-footing rule, why blocks and shims fall short, a snap-on leg that extends in 3/16 inch steps to 10 inches, approved ladder types and duty ratings, and setting up on steps, slopes and curbs.

Steps, sloped lawns, curbs and stair landings leave one rail short, and ladder levelers fix that by extending a leg until the rungs sit level, which Nation Wide Ladder helps crews do with LeveLok kits and Werner and Louisville leveler options. We cover OSHA's footing rule, how a quick connect leveler and its rail-mounted bases work, the ladder types and duty ratings it is approved for, Werner and Louisville fitments and a safe setup on uneven ground.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

Why OSHA and Ladder Makers Call for Levelers on Uneven Ground

OSHA’s ladder rule, 29 CFR 1926.1053, says ladders shall be used only on stable and level surfaces unless they are secured to prevent accidental displacement, and only on slippery surfaces if they are secured or fitted with slip-resistant feet. The same rule sets a non-self-supporting ladder at about one quarter of its working length out from the top support. On a slope or a step, one foot sits higher than the other, the rails lean sideways and the base angle no longer matches that rule. Where a ladder stands on a curb or in a driveway, OSHA also asks for it to be secured or barricaded so traffic cannot knock it out of place.

A board, a brick or a stack of shims under the short rail is the old answer, and Cal/OSHA’s ladder guidance warns against setting a ladder on boxes, bricks, blocks or other unstable bases. That gap is why ladder levelers exist. A leveler is a rated leg that bolts or clips to the rail and extends to make up the difference, so the foot stays on firm ground and the rungs come back to level. That differs from a stabilizer, which works at the top of the ladder. Leveling options sit among the accessories for many Werner extension ladders.

We have supplied ladders to homeowners and contractors for over 50 years, and fitting levelers is one of the simplest ways we have seen crews deal with sloped yards safely.

Werner Extension Ladders

How Quick Connect Ladder Levelers Fit and What They Are Rated For

The LeveLok LL-STB-2QC shows how a quick connect kit works. Two base units stay bolted to the ladder rails, and one leveler snaps onto whichever side needs it, so the leg rides on the ladder only when the ground calls for it. The leg extends in 3/16 inch increments up to 10 inches. Each base unit weighs 9.1 ounces and the full kit 7.8 pounds, and one leveler can serve every ladder on the truck that has bases fitted. Because the bases stay on the rails, the leveler itself can ride in the truck box between jobs.

Ratings decide where it can go. LeveLok says the kit meets the ANSI A14.8 ladder accessory standard and is approved on ladders up to and including Type IAA, 375 pound duty ratings, and it does not recommend the kit for Type III, 200 pound ladders. It is approved for extension, articulating, straight, combination, sectional and step ladders, and the included hardware fits rails 1/2 inch thick or less, with longer bolts and spacers sold separately for thicker rails. LeveLok backs it with a two year parts and labor warranty. Our LeveLok ladder accessories page covers the kit and its straps.

Our team checks the duty rating and rail thickness of each ladder before we quote ladder levelers, so the kit fits the equipment already on your truck.

LeveLok

Matching Ladder Levelers to Werner and Louisville Models

Both big ladder makers offer leveling as an accessory. Werner lists its PK70-1 and PK80-2 levelers as fitting every length of its D6200 and D7100 fiberglass extension series, the PK70-1 for the D1300 and the PK80-2 for the D500, and it lists the PK70-1 for its MT-13, MT-17, MT-22 and MT-26 multi-position ladders, which helps on stairs and sloped floors. Louisville lists the LEVELOK leveler among the accessories for many of its extension ladders. Our Werner ladder accessories and Louisville ladder parts and accessories pages cover the rest of each range.

Setup follows the same order on any model. Set the ladder at the one-in-four angle, extend the leveler until the rungs are level, then check that the leg lock is engaged and the shoe sits on firm ground. Recheck the level each time the ladder moves along a wall, since a slope rarely stays the same from one end of a house to the other. A leveler does not raise the duty rating, so the climber, tools and material still count against it. LeveLok sells replacement shoes in aircraft aluminum or zinc plated steel, so a worn foot can be swapped without retiring the leveler.

Both of our locations open Saturday mornings, so you can bring a ladder in and check leveler fit with us before a weekend job.

Werner Ladder Parts & Accessories

Ladder Levelers Within a Complete Exterior Setup

Levelers handle the bottom of the ladder, while Werner ladder stabilizers handle the top by holding the rails off gutters and glass, and many exterior crews fit both.

When you are comparing ladder makers to pair with your accessories, our ladder and truck equipment brands hub sets them side by side.

Werner Ladder Stabilizers

Quoting Ladder Levelers for the Ladders You Run

Nation Wide Ladder quotes ladder levelers by the series, duty rating and rail thickness of each ladder you send us, and our own trucks deliver them across New England with the ladders they fit.

Ladder Levelers FAQs

Does OSHA require ladder levelers?

OSHA requires ladders to be used only on stable and level surfaces unless secured against displacement. A rated leveler is one way to level the footing on uneven ground.

How far do ladder levelers extend?

The LeveLok LL-STB-2QC leg extends in 3/16 inch increments up to 10 inches.

Which duty ratings can use ladder levelers?

LeveLok approves its kit up to Type IAA, 375 pounds, and does not recommend it for Type III, 200 pound ladders.

Do ladder levelers fit step ladders?

The LeveLok kit is approved for step ladders as well as extension, articulating, straight, combination and sectional ladders.

Which Werner ladder levelers fit the D6200?

Werner lists both the PK70-1 and PK80-2 levelers as fitting every length of the D6200 series.

Can I use blocks instead of ladder levelers?

Cal/OSHA's ladder guidance warns against setting a ladder on bricks, blocks or other unstable bases. Use a rated leveler or secure the ladder as OSHA requires.

Need help choosing the right ladder or truck equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder