Werner range

Werner Single Ladders, From Heavy-Duty Straight to Fiberglass and Manhole Models, Rim Guards and More

Fixed-length straight ladders for scaffold access, pits, vaults and manholes, with the D500-1, D6200-1 and M7100-1 compared on rating, rail material, length and setup.

Werner single ladders are fixed-length straight ladders with no fly section, and the challenge is choosing a length and rail material that suit a landing, pit or vault with no adjustment to fall back on. Nation Wide Ladder helps you size them, across three series rated Type IA or Type IAA, the heavy-duty D500-1, the fiberglass D6200-1 and the M7100-1 built for manhole access.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

Where Werner Single Ladders and Manhole Models Earn Their Place

A Werner single ladder has one section, so there are no locks, no rope and no overlap to manage. Contractors use Werner single ladders for scaffold and staging access, trench and pit entry, mezzanines and any spot where the same height comes up again and again. Werner manhole ladders serve utility, water, sewer and telecom crews who need a dependable way down into vaults.

With nothing to slide or lock, a single ladder has fewer parts to check and fewer ways to be set up wrong, which helps on sites where several crews share equipment. A straight ladder can also cover temporary access, from a trench to a roof hatch, as long as it extends past the landing or can be tied off at the top.

Manhole and vault entry is tighter still. Openings are narrow, the rim is hard on rails, and the climber often has to pull the ladder back out, so a Werner ladder built for that space saves wear on both the equipment and the crew. Water in a vault adds another concern, since Cal/OSHA warns that a wet ladder can conduct current.

Over 50 years of supplying contractors means we understand single ladders as shared site equipment, and we can suggest a length that serves more than one crew.

Werner M7100-1 Series – Type IAA Manhole Ladder

Comparing the Werner D500-1, D6200-1 and M7100-1 Single Ladders

The Werner D500-1 belongs to the same D500 family as the aluminum D500-2 extension ladder and carries a Type IAA rating at 375 pounds, a good fit for heavy use away from electrical hazards.

The Werner D6200-1 fiberglass single ladder is rated Type IA at 300 pounds, and its fiberglass rails make it the choice near energized equipment. It uses twist-proof rung joints, 1.63 inch slip-resistant D-rungs and mar-resistant end caps, comes in lengths from 8 to 20 feet, and has pre-pierced holes for Werner accessories.

The Werner M7100-1 manhole ladder is rated Type IAA at 375 pounds. It is offered at 8, 10, 12 and 16 feet and measures 12.38 inches rail to rail. A 3 foot plastic sleeve guards the rails on the manhole rim, a combined rail shield and shoe protects the bottom of each rail, and vinyl-coated end caps help when lifting it out. Crews with a separable Werner extension ladder can also use its base section as a single ladder.

Our team checks the rating, rail material and length against the site, so the single ladders on your quote suit the work.

Werner D500-1 Series

Werner Single Ladders as Part of a Site Access Plan

A straight ladder is often the fixed access point on a job while other equipment moves around it. Masons and siding crews use one to reach staging, utility crews keep a Werner manhole ladder with their vault entry gear, and builders leave one at a pit or mezzanine for the length of the project. Each of those setups depends on equipment from more than one source, from scaffolding and planks to the racks and boxes that get a long straight ladder to site safely. Thinking about access as a plan rather than a single purchase keeps lengths and ratings consistent.

To round out that plan, you can check every manufacturer we carry in our ladder and truck equipment brands hub.

Werner D6200-1 Series – Type IA Fiberglass Single Ladder

Werner Single Ratings and the OSHA Straight Ladder Rules

Cal/OSHA lists Type IAA at 375 pounds and Type IA at 300 pounds, the two ratings across Werner single ladders we supply. OSHA counts all workers, tools and materials on the ladder toward that rating at any one time. Because a single ladder is not self-supporting, OSHA requires it to withstand four times its maximum intended load when tested at a 75.5 degree angle, or 3.3 times for extra-heavy-duty Type IA metal or plastic ladders.

OSHA sets rung spacing on portable ladders at 10 to 14 inches center to center, and it calls for nonconductive side rails anywhere the worker or ladder could touch exposed energized equipment. In vaults where cables run close by, that rule points toward fiberglass.

Street work adds more. OSHA requires a ladder set where traffic could knock it to be secured or barricaded, with the top and bottom kept clear. Climbers must face the ladder, keep at least one hand on it, and avoid carrying anything that could throw them off balance, so tools for a vault are better lowered separately on a line.

At our Windham and Worcester showrooms you can compare single ladders side by side and talk through the site in person.

Sizing Werner Single Lengths for Landings, Pits and Vaults

With no extension to adjust, the length of Werner single ladders has to be settled before you order. When the ladder gives access to an upper landing, OSHA requires the side rails to extend at least 3 feet past that landing. Where that cannot be done, the top has to be secured to a rigid support with a grab device provided, a common situation at manholes and pits.

Set the base at roughly a quarter of the working length out from the support, the same proportion Werner expresses as one foot out for every four feet of height. For deep vaults or confined spaces, follow your site’s entry procedures, which may call for retrieval gear and a separate lifeline.

To size it, measure the vertical height to the landing, add the 3 feet of rail that must project above it, then allow a little for the lean. At the four-to-one angle the ladder runs about 3 percent longer than the height it climbs, so a 16 foot landing plus the 3 foot extension points to a 20 foot ladder, the longest D6200-1.

Send us the heights and depths as a list, or call 603-434-6911 in New Hampshire or 508-754-3030 in Massachusetts, and we will quote single ladders to match.

Inspecting Werner Single Rails, Rungs and Manhole Sleeves

Inspect rails, rungs, hardware and feet before each use. Werner does not recommend repairing damaged ladders, so a bent or cracked rail means the ladder is retired. OSHA expects a competent person to inspect ladders periodically and after any event that could affect safe use, and Werner manhole ladders that see mud, water and road salt deserve a close look at the feet, rung joints and rim sleeve. Pairing the ladder with a lifeline and harness from our Werner self-retracting lifelines and lifeline systems adds protection on deep descents.

Werner points owners to its Fiberglass Ladder Technical Manual for guidance on service life, storage and resistance to UV, weather and cold. Werner also runs ladder safety training, including its Climbing Pro Ladder Safety 101 and Ladder Core courses on setup, selection and inspection, which suit crews bringing on new hires. Safety labels must stay legible under OSHA rules, and Werner supplies replacements through its customer care team.

A ladder that fails inspection late in the week can be replaced on a Saturday morning, when both of our locations are open.

Why Crews Source Werner Single Ladders From Us

Compare lengths in our single and manhole ladder category or return to the Werner brand overview. We quote Werner single ladders and the M7100-1 by length and rating, with regular weekly deliveries from New Hampshire to crews in Maine.

Werner Single Ladders FAQs

What is the difference between Werner single ladders and extension ladders?

A single ladder is one fixed-length section with no fly section or locks. An extension ladder has two or more sections that slide to adjust reach.

Which of the Werner single ladders suits work near electrical equipment?

Choose the fiberglass Werner D6200-1, since OSHA requires nonconductive side rails where the worker or ladder could contact exposed energized equipment.

What if a Werner single ladder cannot extend 3 feet past a manhole opening?

OSHA allows the ladder to be secured at its top to a rigid support, with a grab device provided for getting on and off.

What rating does the Werner M7100-1 manhole ladder carry?

The Werner M7100-1 is rated Type IAA at 375 pounds and comes in 8, 10, 12 and 16 foot lengths.

How long should Werner single ladders be for a roof hatch or landing?

Measure the height to the landing, add the 3 feet of rail OSHA requires above it, and allow a little for the lean, which adds about 3 percent at the four-to-one angle.

Need help choosing the right Werner equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder