Resources
Truck Cap Ladder Racks, Roof-Mount Clamp & Lock and Drop Down Kits, Over-Cap Racks, Mount Plates and More
Racks that bolt to the rails on a commercial or fiberglass shell set against bed-mounted racks that stand over it, with shell height, wall angle, side doors and capacity.
Choosing truck cap ladder racks starts with the shell, because a shell takes away the open truck bed and changes where a ladder can ride. Nation Wide Ladder compares Holman roof-mount Clamp & Lock, drop down and combo kits with their commercial and fiberglass cap mounts, System One cantilevered racks that stand over the shell, and Holman Pro II and Pro III racks on taller legs, then installs the setup on your truck.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Two Ways to Carry a Ladder Over a Truck Cap
A commercial shell turns a pickup truck bed into a lockable, weatherproof cargo box, which is why so many service contractors run one, but it also takes away the open bed where a ladder would ride. There are two ways around that. The first mounts the rack to the roof of the shell itself, using rails on the shell, so the ladder rides low in roughly the position it would on a work van. The second keeps the rack on the truck bed rails and builds it tall enough to stand over the top of the truck shell, so the shell carries none of the load.
Which route suits a truck depends mostly on the shell. A shell built with roof rails and rated to carry a rack can take a roof-mount kit, while a lighter shell or one without rails points toward a rack that straddles it. The number of ladders and how often they come off matter too, since roof-mount kits come with Clamp & Lock, drop down and combo mechanisms, while a bed-mounted rack carries ladders and long stock on crossmembers.
Our team checks the shell make, its rails and its height on your truck before we quote, so the rack style suits the shell it has to work with.
Holman Truck Cap Ladder Kits That Mount to the Shell Roof
Holman builds its cap rack line in HD aluminum for 6.5 and 8 foot shells and describes them as fitting most commercial caps. Clamp & Lock models hold the ladder with a locking arm, as the rack-only 4A83L for 6.5 foot caps and 4A84L for 8 foot caps, with the 4A85L adding a driver side mechanism to the 4A84L. Drop down kits bring the ladder down beside the truck with a handle and come as singles or doubles, and combo kits pair one drop down and one Clamp & Lock mechanism on the same cap.
The mount kit matters as much as the rack. The Holman 408SC is made for ARE DCU and other commercial truck caps, the aluminum work shells that usually carry roof rails, and the 408GC is a pack of eight slider plates with studs for the rails on ARE fiberglass caps. A bare fiberglass roof without factory rails is not built to carry a ladder rack, so confirm the rails and ask the shell maker for its roof load limit, since the shell rather than the rack often sets the ceiling.
We install the rack, mount kit and slider plates ourselves, lining them up with the rails so the first ladder goes onto a square, tight setup.
Bed-Mounted Truck Ladder Racks That Stand Over the Cap
System One takes the other route with cantilevered racks that mount outside the shell. Four 3/16 inch stainless steel cantilever plates reach out from under the shell and rest on the Pick-up Trak, which spreads the load along the truck bed rail. System One sizes them for caps from cab-high to 30 inches tall, with leg lengths from 24 to 34 inches, and rates them at about 600 lb on a cab-high shell and 400 lb on a 30 inch shell. Its legs sit at a fixed 17.5 degrees, so fiberglass caps generally suit them, while aluminum caps with more vertical walls may need measuring, and side doors on the shell need 5 inches of leg clearance at each end of the bed. The System One truck rack system page sets out the Trak and rig system these build on.
Holman covers capped pickups with Pro II cap racks and taller legs that lift a Pro II by 6 inches on capped full-size trucks, and a Pro III taller-leg kit does the same for a mid-size pickup. Holman full-length bed rails are not offered for a truck with a camper shell, so plan the mounting around the shell from the start of the truck build.
Bring the truck to our Windham, NH or Worcester, MA showroom for a free consultation, and we will measure the shell height and wall angle on your truck with you.
Capped Pickups in a Mixed Work Fleet
Many companies run capped pickups next to vans, and a roof-mount truck rack with the same mechanism as the Holman van racks on the rest of the fleet means any crew can load any vehicle the same way, whether it carries van racks or truck cap ladder racks.
If several makers are on your shortlist, you can set each one side by side in our ladder and truck equipment makers hub.
Truck Cap Ladder Racks Fitted to Your Shell
Cap rails, cap height and the number of ladders you carry decide between a roof-mount kit and an over-cap rack, and Nation Wide Ladder quotes and installs truck cap ladder racks from Holman and System One to match. Call 603-434-6911 in New Hampshire or 508-754-3030 in Massachusetts with your truck, shell make and length.
Truck Cap Ladder Racks FAQs
Can I put a ladder rack on a truck cap?
Yes, if the shell has roof rails and is rated for it. Holman roof-mount kits use the 408SC mount kit on ARE DCU and other commercial caps or 408GC slider plates on ARE fiberglass caps with rails.
What sizes do Holman truck cap ladder racks come in?
Holman sizes its cap racks for 6.5 and 8 foot caps and describes them as fitting most commercial caps.
How tall a truck shell will a System One over-cap rack clear?
System One sizes its cap racks for shells from cab-high to 30 inches tall, with leg lengths from 24 to 34 inches.
How much can a truck cap ladder rack carry?
System One rates its cap racks at about 600 lb on a cab-high shell and 400 lb on a 30 inch shell. For a roof-mount rack, the shell maker's roof load limit often sets the limit, so ask for it.
Do side doors on a truck cap affect the rack?
They can. System One needs room for its legs 5 inches back from the bulkhead and 5 inches forward of the tailgate, so long side doors may interfere.
Can I raise a Holman truck rack to clear my cap?
Yes. Holman taller legs lift a Pro II by 6 inches on capped full-size pickups, and a Pro III taller-leg kit does the same for mid-size trucks.
Need help choosing the right ladder or truck equipment?
Talk to the team or send us your list and we will put a quote together.








