Resources

Ladder Tie-Downs From Clamp & Lock Racks and Work Winches to Retractable Ratchet Straps, Stops, Anchors and More

Securing ladders and cargo on a truck or van rack, with built-in locking racks, winch straps, retractable ratchet pairs, side stops, D-rings and the checks that keep them tight.

Ladder tie-downs decide whether a ladder arrives where you left it, and the challenge is choosing a method that is fast enough to use at every stop. Nation Wide Ladder fits Holman Clamp & Lock and drop down racks that secure the ladder themselves, System One Work Winches, Holman retractable ratchet straps and System One ratchet straps, Magnum D-rings and stops, and the side stops and anchors that hold a load in line.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

Ladder Tie-Downs Built Into the Rack Itself

The most secure ladder is often the one that never needs a loose strap. Holman Clamp & Lock ladder racks use a crossbow design that holds the ladder in place without straps or ties, so the mechanism itself does the work every time the ladder goes up. On a drop down rack the ladder comes down to you on a handle, which removes the climb onto the bumper, and the rack carries the ladder in its own frame on the roof. Built-in tie-downs like these cannot be left behind at the last job site or lost under a seat, which is a large part of their appeal.

System One builds its tie-downs into the rack frame too. System One Work Winches plug into the Heavy I.T.S. gussets on its pickup racks, and into every System One van rack, in about two to three minutes. Each winch carries 7-1/2 feet of 1-1/2 inch polyester strap, and System One rates it at 400 lb with a stated breaking strength of more than ten times that figure. To use one, lift the pawl, pull out the strap, pass it over the load and hook it to an anchor hole or crossmember, take up the slack with the hand wheel and tighten with the handle. The strap winds back onto its spool when the load comes off.

Our team checks whether your rack accepts built-in tie-downs, including the gussets a Standard System One rack needs before winches will fit.

Holman Clamp & Lock Ladder Racks

Ratchet Straps and Retractable Ladder Tie-Downs on a Work Rack

Where the rack has no built-in system, straps carry the load. Holman retractable ratchet straps stay mounted on the rack and wind their webbing back in when released, so they are always there and rarely tangled. Holman sells them in pairs, 1 inch by 6 feet or 2 inches by 7 feet, as plain pairs for crossbar racks (40830 and 40850), with Pro II mount brackets (31500 and 31490) or with Pro III mount brackets (31503 and 31493). The ratchet still does the tightening, so the holding method is the familiar one, while loose tie-downs that used to ride in a bucket or door pocket stay on the rack instead.

System One supplies ratchet tie-downs with 4 or 6 foot straps and gold zinc plated hardware for its Standard series racks that do not take winches. On a pickup with a Magnum headache rack, a powder coated steel D-ring anchor slides in the Glide Track to put a tie-down point wherever the load needs one. Whatever the brand, use a strap near each end of a long ladder so it cannot pivot, and match the wider 2 inch straps to heavier loads.

We install retractable housings and brackets where they can reach both ends of a typical ladder, so the straps line up with the rungs you load against.

Holman Retractable Ratchet Straps

Stops, Anchors and Checks That Keep Ladder Tie-Downs Working

Stops keep a ladder from sliding sideways before a strap is even tight. System One A106 side stops guide ladders on the crossmembers, and A109 Tall Side Stops stand 13 inches tall for stacks that rise above the extension beam, while A100 sliding cargo anchors fit any T-slot. Magnum ladder stops slide in the same Glide Track as its D-ring. The Weather Guard 1275-52-02 steel rack adds a tie-down loop on each leg and four more points along its side members.

Check straps again after the first few miles, because loads settle and webbing can loosen. Look over every strap for cuts, fraying, burns or sun fading, replace a damaged one rather than knotting it, and replace both halves of a pair together. Keep ratchets clear of grit and ice in winter, and dry wet tie-downs before they wind back into a housing in freezing weather. Securing the ladder does not stop at the truck either, since a Tie Down stand-off stabilizer holds an extension ladder 18.5 inches off the wall once it is up against the house.

Send us your rack model and a list of the straps, winches or stops you want, and we will quote them together on one order.

System One Rack Accessories (Side Stops, J-Hooks)

Ladder Racks and Tie-Downs as One Plan

Tie-down choices follow the rack. A rack with built-in locks or winches needs few loose straps, while a plain crossbar rack depends on them, so settling the rack first decides which ladder tie-downs belong on the truck or van.

For the full spread of rack, strap and ladder makers we carry, open our brands of ladders and truck equipment hub.

Ladder Tie-Downs Matched to Your Rack

From built-in locks and winches to retractable straps, stops and anchors, Nation Wide Ladder matches ladder tie-downs to the rack on each vehicle and installs them, with our own trucks delivering across New England.

Ladder Tie-downs FAQs

Do I need straps on a Clamp & Lock ladder rack?

Holman says its Clamp & Lock racks hold the ladder with a crossbow design without straps or ties.

How strong are System One ladder tie-downs?

System One rates each Work Winch at 400 lb and states a breaking strength of more than ten times that figure.

What sizes do Holman retractable ladder tie-downs come in?

Holman sells retractable ratchet straps in pairs, 1 inch by 6 feet or 2 inches by 7 feet, with versions for crossbar, Pro II and Pro III racks.

How many ladder tie-downs should a long ladder have?

Use at least one strap near each end so the ladder cannot pivot, and check them again after the first few miles.

When should I replace ladder tie-downs?

Replace any strap with cuts, fraying, burns or sun fading, and replace both straps of a pair together so tension stays even.

Can Work Winches go on any rack?

They fit System One I.T.S. racks, meaning Heavy I.T.S. pickup racks and all System One van racks. Standard series racks need new gussets and braces first.

Need help choosing the right ladder or truck equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder