Werner Fall Protection Harnesses
Werner Arc Flash Harnesses in Standard, Positioning and Construction Layouts, With Kevlar Webbing and More
The H914004 standard, H934004 positioning and H934104 construction models for electrical and utility work, with Kevlar webbing, dielectric hardware, ASTM F887, OSHA 1910.269 and inspection points.
Werner arc flash harnesses are built for electricians, utility line crews and plant maintenance teams who work at height where an electric arc is possible. Ordinary webbing may not hold after an arc, so Nation Wide Ladder helps electrical crews choose among three Werner Kevlar models with dielectric hardware, the H914004 standard, H934004 positioning and H934104 construction layouts, plus the matching Kevlar arc flash lanyards.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Who Needs Werner Arc Flash Harnesses at Height
Standard polyester harnesses are made to stop a fall, not to come through an arc flash. When an electrical fault releases an arc near a worker in a bucket, on a substation structure, up a pole or beside a cable tray, the heat can damage ordinary webbing and hardware at the moment the worker needs them to hold. Werner aims this range at that combination of hazards, which suits electrical contractors, utility crews, telecom workers on shared poles and facility teams maintaining switchgear.
OSHA spells out the requirement for power generation, transmission and distribution work. Under 1910.269, fall arrest equipment used by workers exposed to flames or electric arcs has to pass a drop test after exposure to an electric arc with a heat energy of 40 calories per square centimeter, plus or minus 5, so the gear must still catch a fall afterward. The same standard requires workers more than 4 feet up on poles, towers or similar structures to use fall arrest, positioning or restraint. Arc-rated clothing protects the wearer, while the Werner harness has to stay a working fall arrest system after the arc.
Our team helps you check the access method and arc exposure on the job before choosing among the Werner models.
Werner Arc Flash Harnesses in Three Layouts
The range covers the three layouts electrical work tends to need. The Arc Flash H914004 standard harness has a single back D-ring, which keeps aerial lift and bucket work simple. The Werner H934004 positioning harness adds hip D-rings, giving a line worker a place to clip a positioning strap while working with both hands. The Arc Flash H934104 construction harness keeps the back and hip rings and adds waist padding for crews who carry tools all day.
All three share the core build. Werner makes the webbing from Kevlar, pads the shoulders, specifies dielectric hardware and fits pass-thru leg connections. After a fall, yellow handles at the seat help the worker reach the Gravity Override position, which Werner designs to reduce the hazards of suspension trauma while rescue is organized. For the connection, Werner also makes Kevlar arc flash twinleg lanyards such as the C911100 and C911200, because an ordinary polyester lanyard would leave part of the system without the same arc protection.
You can talk through all three Werner layouts at a free consultation in our Windham NH or Worcester MA showroom.
ASTM and OSHA Standards Werner Cites for Arc Exposure
Werner states that the Kevlar web, padded shoulders and dielectric hardware in these harnesses meet the ASTM F887 requirements for arc flash. It also cites ANSI Z359.11 and the OSHA fall protection requirements in 1926 for construction and 1910 for general industry. That combination matters because Werner arc flash harnesses face two tests, surviving the arc and then performing as normal fall arrest harnesses.
The fall arrest numbers for these Werner models match any other harness. OSHA construction rules cap the arresting force at 1,800 pounds, limit free fall to 6 feet and deceleration distance to 3.5 feet, and require connectors of drop forged, pressed or formed steel or an equivalent material, so dielectric hardware still meets those rules. The rating on a Werner harness does not replace the employer’s electrical safety program, since arc-rated clothing, approach boundaries and energized work procedures still apply. Read the label on Werner harnesses, and confirm that every lanyard, snap hook and anchor connector suits arc exposure before it goes onto an energized job.
Send us the full system list for an energized job, or call 603-434-6911 in NH or 508-754-3030 in MA, and we will quote matched Werner Kevlar gear.
Choosing and Inspecting Werner Arc Flash Models
Pick Werner arc flash harnesses by the task. Bucket work generally needs only the back ring of the H914004, pole and tower work where the worker leans into a strap calls for the hip rings of the H934004, and crews carrying pouches and meters all shift get extra waist padding on the H934104. Pass-thru legs take a moment longer to fit, so set each Werner harness to its wearer and keep it assigned. The store listings are XL, so tell us the sizes on the quote.
Werner calls for a pre-use check and an annual inspection by a competent person other than the user. Look along the Kevlar webbing for cuts, burns, discoloration and glazed spots, and examine the dielectric hardware for cracks and chips, since damage may not look like the bending or rust on steel. Treat any Werner harness exposed to an arc event as suspect until a competent person examines it, and retire one that has arrested a fall. Werner allows hand washing in mild soap with air drying out of direct sun, never machine washing.
Both our showrooms keep Saturday morning hours, so a line crew can pick up a replacement Werner harness after an arc exposure without losing a weekday.
Werner Arc Flash Harnesses Within a Matched Electrical Crew Kit
Kevlar harnesses are one layer of the system. Werner’s Kevlar lanyards come as twinleg designs with snap hooks, rebar hooks or a loop end, covered under our Werner twin leg lanyards, and the other layouts sit in the broader Werner harness range. Electrical contractors often equip a truck with fiberglass ladders and fall protection from several manufacturers at once.
Whoever else is on your equipment list, you will find them in our ladder and truck equipment brands hub.
Why Electrical Crews Buy Werner Arc Flash Harnesses From Us
We have served contractors for over 50 years, and our own trucks deliver door to door across New England with shipping anywhere in the US. Browse our harness category or the Werner brand page, then tell Nation Wide Ladder the electrical work, access method and crew sizes, and we will quote Werner arc flash harnesses with matching Kevlar lanyards.
Werner Arc Flash Harnesses FAQs
What standards do Werner arc flash harnesses meet?
Werner cites ASTM F887 for arc flash, ANSI Z359.11, and OSHA 1926 and 1910 fall protection requirements.
What does OSHA require for Werner fall gear exposed to electric arcs?
OSHA 1910.269 requires the equipment to pass a drop test after exposure to an electric arc with a heat energy of 40 calories per square centimeter, plus or minus 5.
Which Werner arc flash harness suits bucket truck work?
The H914004 has a single back D-ring for fall arrest, which covers aerial lift and bucket work that needs no positioning rings.
Is there a matching Werner arc flash lanyard?
Yes. Werner makes Kevlar arc flash twinleg lanyards, such as the C911100, that cite ASTM F887 and ANSI Z359.13.
Can Werner arc flash harnesses be reused after an arc exposure?
Treat it as suspect and have a competent person examine it first. Retire any harness that has arrested a fall.
Need help choosing the right Werner equipment?
Talk to the team or send us your list and we will put a quote together.








