Holman Truck Racks & Equipment
Holman Pro Rack, 1200 Series for Pickups and Work Bodies, With Swing-Out Crossbar, Grab Handles, Wind Deflector and More
A heavy-duty truck frame that builds on the Pro II, fitting short to long pickup beds and work bodies, with a locking swing-out rear crossbar, low grab handles and a standard wind deflector.
Contractors who load lumber, pipe and ladders over a pickup bed need a frame that stays rigid and makes loading easier, so we fit the Holman Pro Rack, the 1200 Series. At Nation Wide Ladder we match the 1200 Series to full-size pickups, service bodies and platform bodies, from short beds to long beds, and install it. The Holman design adds a swing-out rear crossbar that locks open, adjustable front leg mounting, improved foot mounting, low rear grab handles and the Pro Wing wind deflector as standard.

- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Where the Holman Pro Rack Fits in the Lineup
Holman describes the 1200 Series as a new line of heavy-duty racks and as an evolution of its Pro II design. Holman set out to improve the older design in several places without giving up the toughness and adaptability its owners expect, so the Holman Pro Rack is the next step for crews who already know the Pro II. It sits within our wider range of Holman truck racks.
Holman built the 1200 Series for full-size work trucks, and names service bodies and platform bodies among its uses too. On pickups, Holman says it can take every bed type from long bed to short bed, which makes it practical for fleets with a mix of cab and bed combinations.
That range of fit matters to a business that wants one design across its trucks. Instead of tracking separate lines for different beds and bodies, a fleet can aim to standardize on the 1200 Series and keep spare parts and loading habits consistent. It also simplifies training, since every driver meets the same crossbar, handles and mounting when they climb up to load.
Our team checks your truck’s cab, bed length or body type against the Holman fitment before you order, so the Pro Rack arrives set up for your vehicle.
Holman Pro Rack Features That Speed Up Loading
The swing-out rear crossbar is the headline change. Holman designed it to lock in the open position, so the back of the frame stays clear while you slide long material in from behind the truck, and it closes again for the drive. For a crew loading long lumber or conduit alone, that open rear end saves lifting each piece over a bar.
Adjustable front leg mounting lets one 1200 Series fit more vehicle applications, which helps when a fleet mixes truck models. Holman also reworked the foot mounting and says the new design cuts horizontal deflection and makes for a stronger build, which in practice means less side-to-side movement under load. That matters on a truck that runs highway miles with a load on top, where a rack that sways works its fasteners loose over time.
Two smaller touches matter on a busy day. Grab handles mounted low on the rear give you a solid hold when climbing up to load or strap, and the Pro Wing wind deflector now comes standard, so there is no separate part to order for the front. The Holman 1200 Series listing sets out each of these changes.
We install the 1200 Series with its Pro Wing and set the front legs for your truck, so the frame sits square and the rear crossbar swings and locks as designed.
Holman Pro Rack and the Rest of the Truck
A rack carries the long material, but most work trucks also need a toolbox, bed rails or other storage. Planning the 1200 Series alongside the rest of the truck keeps legs, boxes and rails from competing for the same space.
When you are weighing Holman against other rack makers, browse our ladder and truck equipment brands hub.
Picking the Holman Pro Rack for Your Fleet
The Pro II remains a long-running design with many cab, bed and cap versions, while the 1200 Series brings its loading and mounting improvements in a single adjustable design. Crews that load from the rear often, work alone or run several truck models will notice the changes most, while a fleet already settled on Pro II hardware may prefer to stay with it. If your trucks carry both, ask us how the two designs compare on your specific vehicles.
Holman describes its truck racks as built from bigger, thicker round tubes with extensive gusseting at the legs and crossbars. Ask us to confirm the Holman load rating for your truck and body before you plan heavy loads, and spread long material along the rack rather than piling it at one end.
Once installed, check leg and foot fasteners after the first few loads and every few months after that, keep the swing-out crossbar’s lock and pivot clear of grit and ice, and look over the Pro Wing mounts for looseness. In a New England winter, rinse road salt off the frame regularly so it does not sit in joints and around fasteners. Keep the grab handles tight too, since they take your weight.
Send us your truck details and we will quote the 1200 Series, at 603-434-6911 in NH or 508-754-3030 in MA.
Order the Holman Pro Rack
The Holman Pro Rack gives a work truck a heavy-duty frame with easier rear loading and a cleaner front end, and our own trucks deliver across New England, with shipping anywhere in the US. Tell us the truck, the bed or body, and the loads you carry, and we will price the setup. Browse Holman products in our store or read our Holman overview before you ask for a quote.
Holman Pro Rack FAQs
What is the Holman Pro Rack?
It is the Holman 1200 Series, a heavy-duty design for full-size pickups as well as service and platform bodies, which Holman calls an evolution of its Pro II.
Does the 1200 Series fit short bed pickups?
Yes. Holman says the 1200 Series can take pickup truck types from long bed to short bed.
What changed in the 1200 Series compared with the Pro II?
Holman lists a swing-out rear crossbar that locks open, adjustable front leg mounting, improved foot mounting that reduces horizontal deflection, low rear grab handles and a standard Pro Wing wind deflector.
Does the 1200 Series come with a wind deflector?
Yes. The Pro Wing wind deflector is now included as standard.
Do you install the Holman Pro Rack?
Yes. We provide installation for Holman products, including the 1200 Series and its Pro Wing.
Need help choosing the right Holman equipment?
Talk to the team or send us your list and we will put a quote together.


