System One Truck Racks

System One Rack Accessories, With Tall Side Stops, Cargo Anchors, J Hooks, Window Guards, Tie-Downs and More

Side stops, sliding anchors, hose and cord hooks, bucket hooks, tool box hangers, lift kits, strobe mounts and conduit carriers that bolt into the T-slots of a System One rack.

A ladder rack only earns its keep when ladders stay put and cords, hose and pipe have a place to ride, and System One rack accessories handle that by bolting into the T-slots already built into the rack system, which Nation Wide Ladder supplies and fits across New England. We list the A109 Tall Side Stops and can quote side stops, A100 sliding cargo anchors, A114 and A111 hooks, A141 Quick Hooks, tool box hangers, the A123 lift kit, the AWG window guard and strobe mounts.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

Why System One Rack Accessories Bolt Straight Into T-Slots

Every System One rack is covered in recessed T-slots. The truss legs carry three, the crossmembers carry three, and the Pick-up Trak along the bed rail carries more, all sized for ordinary 5/16 inch carriage bolts. That design is the reason the system can take so many add-ons without drilling the truck. Because the slots run the full length of each part, an accessory can sit exactly where a ladder rung or pipe end needs it.

An accessory slides into the slot wherever it is needed, then tightens with a bolt or a brass insert knob. If the job changes next season, it slides somewhere else or comes off. Only a few parts that mount to the extension beam flange of a Contractor Rig call for drilling.

Most crews start with stops to keep ladders in line, then add anchors, hooks and guards as their loads show what is missing. Building up the system this way keeps cost in step with need.

Our team helps you pick the System One rack accessories that match what you haul and the rack you already run.

System One A109 – Tall Side Stops

System One Rack Side Stops, Tall Guides and Sliding Anchors

The System One A109 Tall Side Stops are for loads that stand taller than the extension beam. Each stop is 13 inches tall, cut from 1/4 by 2 inch aluminum, and bolts anywhere along the horizontal flange of the extension beam, with drilling required. They keep stacked ladders or lumber from sliding sideways off a Contractor Rig.

Standard A106 side stops, in 1/4 by 1 inch aluminum, guide ladders, lumber and pipe on the crossmembers, and a side stop and anchor version adds a hole for tying off rope. The A100 sliding cargo anchor is cast aluminum with a brass insert knob and fits any T-slot on the rack, though most end up in the Pick-up Trak to stop pipe and fittings rolling around the bed. System One also sells the anchors and stops in four-piece kits.

Ratchet tie-downs, with gold zinc plated hardware and 4 or 6 foot straps, suit racks that do not take Work Winches.

We install the stops and anchors along with the rack, so each part is bolted and positioned for your ladders on the first fitting.

System One Rack Hooks for Cord, Hose, Buckets and Rope

Hook accessories put unused space to work. The A114 Crossmember J Hook mounts under a crossmember, even with a window guard fitted, and stands 10 inches tall with a 5 inch deep hook, sized for coils of extension cord, welding cable or hose that will not wind tight. The A111 Hooked Bracket is heavier still, and System One says a pair mounted facing each other takes up to 400 feet of extension cord or 200 feet of air hose.

The A141 Quick Hook is stainless steel and clips into the Pick-up Trak at any point to hold cords or keep 5 gallon buckets from sliding. The A107 hook takes small coils of rope and gives a ratchet strap hook somewhere to sit when the rack is empty.

Hooks under the crossmembers stay out of the way of ladders, so they add storage without reducing what the rack carries on top.

Bring a list of hooks and stops you want and we will quote them as a single order, or call 603-434-6911 in New Hampshire or 508-754-3030 in Massachusetts.

Guards, Hangers, Lift Kits and Mounts Among System One Rack Accessories

The remaining accessories handle protection, box mounting and lighting. The AWG cab window guard bolts into the T-slot on the inner face of each truss leg and uses aluminum angle with expanded aluminum mesh to protect the rear window from shifting cargo. Tool box hangers bolt into the T-slot under a Heavy I.T.S. gusset and into the wall of a top-side or low-side box, removing the need for legs on the bed floor.

The A123 crossover box lift kit is a pair of 3 inch square aluminum tube spacers with 4 inch stainless carriage bolts, raising a crossover box to free up space underneath. The A321 side strobe mount, cut from .100 inch aluminum, holds a strobe without using crossmember space, and the A306 kit adds a cast aluminum door and end cap to 4 or 6 inch PVC pipe for carrying conduit. Color inserts in 66 shades round out the system and let it match the truck.

Both of our showrooms open Saturday mornings, so you can look over accessory options with us without missing a workday.

Fitting System One Rack Accessories Into a Full Truck Layout

Accessories work best when they are chosen with the rack, the boxes and the ladders in mind. A tall stop only helps if the ladder stack needs it, and a window guard matters most where cargo can shift forward.

You can set System One beside the other truck equipment makers we carry in our ladder and truck equipment brands hub.

Order System One Rack Accessories

After more than 50 years of fitting out contractors’ trucks, Nation Wide Ladder can supply and install the System One rack accessories that suit your loads. See them alongside System One truck racks and the System One brand overview, then browse our System One store.

System One Rack Accessories FAQs

What are System One A109 Tall Side Stops used for?

They keep ladders or lumber that stand taller than the extension beam from sliding sideways. Each stop is 13 inches tall and bolts to the extension beam flange.

Do System One rack accessories need drilling?

Most slide into the T-slots with carriage bolts or knobs. Parts that mount on the extension beam flange, such as the tall side stop, need drilling.

Which System One rack accessory holds extension cords and hose?

The A114 Crossmember J Hook and the heavier A111 Hooked Bracket. System One says a facing pair of A111 brackets holds 200 feet of air hose or 400 feet of cord.

Can I add a window guard to a System One rack?

Yes. The AWG cab window guard mounts in the T-slot on the inner face of each truss leg.

Are System One rack accessories sold in kits?

Yes. System One sells kits such as four sliding cargo anchors or four sliding ladder stop anchors, and a full commercial kit of anchors and hooks.

Need help choosing the right System One equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder