System One Truck Racks
System One Work Winches for I.T.S. Racks, With Cast Aluminum Bodies, Polyester Straps, Ratchet Pawls, Handles and More
How the AWW winch plugs into I.T.S. gussets and brackets, its 400 lb rating, strap and handle design, left or right hand fitting, and which pickup and van racks accept it.
Ropes and bungee cords are slow and unreliable on a loaded rack, and System One Work Winches replace them with a built-in strap and ratchet system that Nation Wide Ladder supplies and fits on System One racks across New England. We list the AWW Work Winch, sold in sets such as the four-winch AWW-4 kit, for Heavy I.T.S. pickup racks and every System One van rack, with the polyester strap, handle and hardware each winch needs.

- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Why Crews Choose System One Work Winches Over Rope and Bungees
Tying down ladders and pipe several times a day adds up. Knots slip, bungees stretch and fade, and loose rope ends whip in the wind. System One built the Work Winch so the strap, ratchet and handle stay on the rack, ready whenever a load goes up.
Using it is simple. Lift the pawl, pull out as much strap as the load needs, pass it over the cargo and clip the hook to an anchor hole or under a crossmember. Wind up the slack with the take-up hand wheel, then tighten with the handle. Unloading reverses the steps, and the strap winds back onto its spool rather than being thrown in the cab.
System One describes the winch as an integral part of the rack rather than a bolt-on extra, because the heavy gussets and brackets on its I.T.S. racks form the frame the winch turns in. That is why the winch suits System One racks only.
Send us a list of the racks on your trucks and we will quote the number of Work Winches each rack needs, or call 603-434-6911 in New Hampshire or 508-754-3030 in Massachusetts.
Inside System One Work Winches, From Cast Body to Strap Hook
The winch body, including shaft and spool, is cast from 356 aluminum alloy and heat treated. System One rates each winch at 400 lb and states a breaking strength of more than ten times that figure. The shaft turns in a PVC bearing pressed into the I.T.S. bore, and large stainless steel thrust washers keep aluminum from rubbing against aluminum.
The strap is 7-1/2 feet of 1-1/2 inch polyester, chosen over nylon because it has higher tensile strength and stretches less in wet weather. It ends in a vinyl coated hook made from 3/8 inch tempered steel. The pawl rides on a 5/16 inch stainless steel clevis pin, and its built-in fingerhold makes it easy to lift.
The ratchet wheel has teeth undercut on both sides, so a winch can be fitted for left or right hand operation. The aluminum handle has a keyhole that grips the hex on the shaft for tightening and lets it spin freely when hanging, and a quick release linch pin lets you store the handle separately.
We install each winch along with the racks we fit, so each winch goes into the correct gusset with its pin, washers and strap in place.
Which Racks Accept System One Work Winches
Only I.T.S. racks take the winch. I.T.S. stands for Integrated Tie-Down System, and on a pickup it means the Heavy I.T.S. gussets in the upper corners, which have the bore for the winch shaft and a hole for the pivot pin. System One makes those bores the same size on every I.T.S. gusset and bracket, so a single winch design fits pickup, service body, enclosed body and van racks alike. All System One van racks are I.T.S. series as standard.
Standard series pickup racks will not take a winch as built. According to System One, a Standard rack made after April 1, 2000 takes winches once four gussets and four braces are replaced, and earlier racks are harder to convert.
Each winch plugs into its gusset in about two to three minutes and is held by a 1/4 inch stainless cotter pin through the shaft.
Bring your rack details to our Windham NH or Worcester MA showroom for a free consultation, and we will confirm whether it can take a winch.
Care and Inspection for System One Work Winches
The winch combines aluminum alloy, stainless steel and a PVC bearing, so there is no plated steel to rust anywhere in the system. Care is mostly about the strap. Look for cuts, fraying and abrasion where it crosses the edge of a load, and replace a damaged strap before the next trip rather than knotting it.
Check that the pawl drops cleanly into the ratchet teeth and that the cotter pin and linch pin are present. Keep the hook clear of sharp edges, and when the rack is empty, wind straps fully onto their spools so they do not flap or wear. A handle left on the shaft is always ready, while a handle kept in a tool box is harder to lose to theft.
Tighten straps again after the first few miles of a trip, because loads often settle. A strap that has been cut or heat damaged should be replaced rather than repaired, since knots weaken the webbing.
Our own trucks deliver door to door across New England, so replacement straps and winch kits can reach your shop or yard.
Where System One Work Winches Sit in a Truck Equipment Plan
Tie-downs are only as useful as the rack and anchors around them. Planning winches along with crossmembers, side stops and cargo anchors makes it easier to secure mixed loads of ladders, pipe and lumber on a work truck.
You can see every truck equipment maker we carry, side by side, in our ladder and truck equipment brands hub.
Order System One Work Winches
For over 50 years Nation Wide Ladder has outfitted contractors’ trucks, and we can add System One Work Winches to the I.T.S. rack you already run or a new rack. See the AWW Work Winches listing, other System One truck racks and the System One brand page, or browse our System One store.
System One Work Winches FAQs
What is the rating of System One Work Winches?
System One rates each Work Winch at 400 lb and states a breaking strength of more than ten times that rating.
Will System One Work Winches fit my rack?
They fit I.T.S. series racks, meaning Heavy I.T.S. pickup racks and all System One van racks. Standard series pickup racks need new gussets and braces first.
How long is the strap on a System One Work Winch?
Each winch uses a 7-1/2 foot by 1-1/2 inch polyester strap with a vinyl coated hook made from 3/8 inch tempered steel.
Can a Work Winch be set up for left or right hand use?
Yes. The ratchet wheel teeth are undercut on both sides, so the winch can be fitted for either hand.
How many System One Work Winches come in a kit?
The AWW-4 kit includes four winches with straps and handles, which is a common setup for a pickup rack.
Need help choosing the right System One equipment?
Talk to the team or send us your list and we will put a quote together.


