Scaffolding

Pump Jack Scaffolding With Aluminum Poles, Joints, Braces, Stages, Safety Nets and More

Alum-A-Pole scaffolding poles from 6 to 24 feet, joints and folding braces, the Pro-Jack, stages with end rails, three 22 foot nets, starter packages, OSHA bracket rules and the ReechCraft Bronco for uneven ground.

Pump jack scaffolding lets a small crew raise a platform up a long wall a few inches at a time, which suits siding, painting, window and trim work on houses and light commercial buildings. Nation Wide Ladder lists the Alum-A-Pole system contractors order most and counts the parts to each wall, covering aluminum poles and joints, folding braces, Pro-Jack pump jacks, stages and end rails, safety nets and pole packages, plus the ReechCraft Bronco tripod filed in the same category.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

Pump Jack Scaffolding Poles, Joints and Wall Braces

The pole is the spine of pump jack scaffolding. Alum-A-Pole pump jack poles pair structural aluminum with industrial rubber permanently bonded to one face, where the pump jack grips, and come as the 6 foot AP-06, 12 foot AP-12, 18 foot AP-18 and 24 foot AP-24, each lab tested to 5,000 pounds with a lifetime warranty on our listing. For walls taller than one length, the APJ pole connector splices poles together and reinforces the joint, and our listing describes three separate safety stops on it.

Poles stand only as well as they are braced. The APB folding support brace folds for carrying, swivels to attach at different angles to a roof and has a brace pullout backup safety system. OSHA’s pump jack paragraph, 29 CFR 1926.452(j), requires poles secured to the structure by rigid triangular bracing or its equivalent at the bottom, the top and other points as needed. When a pump jack has to pass a brace on the way up, an extra brace goes about 4 feet above it and stays until the original is put back. The same paragraph still covers wood scaffolding poles, which have to be straight-grained and free of weakening defects, with mending plates at every spliced 2×4.

Give us the eave heights and wall lengths, and our team will select pole lengths and joints so each splice lands at a height you can assemble from the ground.

Alum-A-Pole – Pole Packages

Pump Jack Stages, End Rails and Safety Nets for Each Wall

The Alum-A-Pole PROJACK pump jack does the lifting. A foot pump on each jack raises the stage, the arm telescopes to 27 inches, and our listing gives a 4,000 pound test figure, three separate backup safety systems, a self-storing Saf-T-Crank handle with an anti-spin feature and a Saf-T-Lok chain that secures the staging and deters theft. Every stage needs a pump jack at each end, so linked stages share the pump jacks on the poles between them.

Stages and rails make the scaffolding deck. Alum-A-Pole stages are rated for two people and 500 pounds, and the SNERS-14 and SNERS-20 end rails close the open end of a 14 or 20 inch stage to help prevent walk-off accidents, fitting Alum-A-Pole stages only. Three 22 foot folding nets share one listing with different ratings. The yellow Alum-A-Pole Simms net is rated for fall protection and debris at 200 pounds per square foot with Alum-A-Pole planks only, the blue Werner PJ-SN is debris and man rated, and the orange NWPJ-SN is a debris net rated at 285 pounds tensile strength and 380 PSI burst. For a first setup, Alum-A-Pole pole packages bundle two or three 24 foot poles with matching braces and pump jacks, with or without workbenches and a 14 inch by 24 foot stage.

Our Windham, NH and Worcester, MA showrooms offer free in-person consultations, where you can go over pump, stage and net options with our team.

Alum-A-Pole APJ – 6′ Pole Connector

Pump Jack Scaffolding Ratings, OSHA Bracket Rules and the Bronco Tripod

OSHA 1926.452(j) requires pump jack brackets, braces and accessories made from metal plates and angles, with two positive gripping mechanisms on each bracket to prevent slipping. A workbench may never be the standing platform, though it can serve as the toprail when it meets the guardrail strength and height criteria. Under the general scaffold rule, pump jack platforms may be as narrow as 12 inches, and anyone more than 10 feet above a lower level needs fall protection. Alum-A-Pole rates its full scaffolding system for two workers and 500 pounds with a 4 to 1 safety ratio, and says it holds OSHA approval to a 50 foot shoulder working height.

For first-story work on sloped or broken ground, the store files the ReechCraft 4026200 Bronco beside the pump jack scaffolding, though it is a three-legged aluminum tripod rather than a pump design. Each Bronco weighs 16 pounds, a pair supports 600 pounds or a 24 foot plank, and ReechCraft rates each tripod at 300 pounds. Our listing gives a maximum working height of 12 to 13 feet, while ReechCraft describes a 3 to 5 foot platform that lets most users reach roughly 11 feet. Our ReechCraft page covers the Bronco beside the drill-driven PowerPole.

We run regular weekly deliveries from New Hampshire to Maine, so 24 foot poles and stages reach crews there between phases of a job.

Reechcraft 4026200 – Bronco Scaffolding System

Pump Jack Scaffolding Beside Siding Brakes and Ladders

Exterior crews rarely run a pump jack setup alone. Extension ladders set the first braces and reach the roof, a siding brake bends trim on the ground beside the poles, and the truck rack has to carry 24 foot poles and stages between houses. The full Alum-A-Pole system, including Alum-A-Scaff stages and workbenches, is laid out on our Alum-A-Pole pump jack scaffolding page.

Line up the ladder, rack and brake makers we stock in our ladder and truck equipment brands hub.

Alum-A-Pole APB – Folding Support Braces

Pump Jack Scaffolding Counted and Quoted for Each Wall

Nation Wide Ladder has outfitted homeowners and contractors for more than 50 years, and we quote pump jack scaffolding pole by pole, matching pump jacks, braces, stages and rails to your wall heights, then deliver across New Hampshire, Massachusetts, Connecticut, Rhode Island, Vermont and Maine. Compare pump systems with frame and interior towers in our scaffolding overview.

Pump Jack Scaffolding FAQs

What lengths do pump jack poles come in?

Alum-A-Pole scaffolding poles come in 6, 12, 18 and 24 foot lengths, and the APJ connector splices two together for taller walls.

What is the rated load of pump jack scaffolding?

Alum-A-Pole rates its full system for two workers and 500 pounds with a 4 to 1 safety ratio, with poles lab tested to 5,000 pounds and the Pro-Jack to 4,000.

How do you pass a brace with a pump jack?

OSHA requires an extra brace about 4 feet above the one being passed, left in place until the pump jack has moved and the original brace is back.

Can a workbench serve as the pump jack scaffolding platform?

OSHA bars it, though a workbench can act as the toprail if it meets the guardrail criteria in 1926.451.

Is the ReechCraft Bronco a pump jack?

It is a three-legged aluminum tripod that holds a plank level on uneven ground, filed beside the pump jack systems, with a pair supporting 600 pounds.

Which safety net fits pump jack scaffolding?

Three 22 foot nets are listed, and the yellow Alum-A-Pole Simms net is rated for fall protection and debris only with Alum-A-Pole planks.

Need help choosing the right ladder or truck equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder