Scaffolding
Scaffold Accessories for Leveling, Rolling, Bracing, Access, Hoisting and Roof Work and More
Base plates, leveling jacks, casters and outriggers, straddle and diagonal braces, pins and tie bars, access ladders and stairways, hoisting gear, chimney brackets and wall brackets for any frame scaffold.
Scaffold accessories decide whether a frame tower stands level, stays put, rolls when it should and gives the crew a safe way up, so these accessories deserve as much planning as the frames. Nation Wide Ladder lists the parts contractors order most for mason style and light duty frames and matches each one to your tower, covering base plates, leveling jacks, casters and outriggers, braces, pins and tie bars, end and side arms, access ladders and stairways, hoisting gear, debris netting, chimney brackets and carpenter wall brackets.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Footing Scaffold Accessories for Level, Rolling or Wider Towers
Every scaffold leg needs a foot, and footing is where scaffold accessories start. The NWBP base plate adds stability and spreads the load, and OSHA 29 CFR 1926.451(c)(2) asks for supported scaffold legs to rest on base plates and mud sills or another firm foundation that is level, sound and able to carry the loaded scaffold without settling. On uneven ground, our leveling jacks come with a base plate attached, with standard NWLJ jacks 24 inches tall and light duty NWLDLJ jacks 12 inches, plus swivel leveling jacks for angled surfaces and separate leveling stems.
To roll a scaffold, NWL casters secure to the frame legs on swiveling rubber tires with locks, as the 8 inch NWC-08 for mason frames and the NWLDC and NWLDC-05 for light duty frames. NWOR mason and NWLDOR light duty outriggers widen the base of a mobile tower, need a cross brace on the bracket to stabilize them, use 2 foot stud spacing for that brace and ship without casters. The outrigger listing notes that a freestanding tower taller than four times its minimum base dimension has to be restrained from tipping, and that Cal/OSHA and some agencies apply a stricter 3 to 1 ratio.
Tell us the ground conditions and whether the tower rolls, and our team will choose the footing scaffold accessories that suit your frames.
Braces, Pins, Ties and Arms Among Our Scaffold Accessories
Bracing accessories keep a scaffold square. The NWSB straddle brace adds stability to the inside of the frames, and NWDB diagonal braces in 7, 8 and 10 foot lengths run corner to corner across towers that are cross braced or straddle braced, while the listing adds that a fabricated plank on the bottom section also helps stop racking. The NWTB tie brace anchors a tower to the structure, in 36 and 48 inch lengths with a swivel coupler to set the distance from the wall, and its listing recommends tie-ins for supported scaffolds with a 3 to 1 height to base ratio.
The smallest scaffold accessories hold everything together. We list NWSP snap pins with a locking wire, NWTP toggle pins with a swivel bar, NWPT pigtails, which are gravity pins fitted through the tubing, and the NWSC swivel clamp for mason frames. The NWEA end arm adds an overhang to bring the deck closer to the work, and NWSA side arms in 20 and 30 inch lengths extend the work area outward. Those arms let a crew reach past a sill, cornice or bump-out without rebuilding the tower further from the wall.
Send us the parts list for your towers, and we price those scaffold accessories by quote at 603-434-6911 in NH or 508-754-3030 in MA.
Access, Hoisting, Roof and Wall Bracket Scaffold Accessories
OSHA 1926.451(e) requires proper access once a platform sits more than 2 feet higher or lower than the point of entry, and it bars crossbraces as a way up. The NWL ST-7 scaffolding stairway fits 6 foot 4 inch frames or walk-thru frames and comes with handrails, the NWAL64 access ladder fits 6 foot 4 inch frames on rolling or stationary towers with optional NWALHR handrails, and NWCL tubular climbing ladders mount outside any tower in 3 and 6 foot sections with a top section and clamps, during erection or after.
Among the hoisting scaffold accessories, the NWHA hoist arm has a tubular steel frame, a closed steel loop for the wheel and a 360 degree swivel head with a 100 pound capacity. The NWGW hoist arm wheel has a 12 inch sheave rated to 1,200 pounds for rope up to 1 inch, and our hoisting rope is 3/4 inch manila with a steel hook, so plan lifts to the arm’s lower figure. On roofs, NWCB chimney brackets level a sloped roof so 5 foot wide frames can go up around a chimney, adjusting from 2/12 to 12/12 pitch, and the NWCWB carpenter wall bracket with NWCWBP posts and the SN8150-FR fire retardant debris net round out our scaffold accessories.
Having served homeowners and contractors for over 50 years, we can help you plan access, hoisting and netting around the tower before the frames go up.
Scaffold Accessories That Complete Frames, Planks and Guardrails
Scaffold accessories turn frames, planks and rails into a tower suited to one site, whether that means a leveled base on a sloped driveway, casters for an interior run or a stairway for a crew carrying material. Each is sized to the frame grade, so mason and light duty versions are separate items. Panels for walk-thru and cross braced sides are covered with our scaffold guardrails.
Browse ladders, racks and access gear by maker in our ladder and truck equipment brands hub.
Scaffold Accessories Quoted With Your Frames
Nation Wide Ladder quotes scaffold accessories with the frames they fit, so the plates, pins, braces and access parts arrive matched, delivered on our own trucks across New Hampshire, Massachusetts, Connecticut, Rhode Island, Vermont and Maine. Start from our scaffolding overview to see where these accessories fit.
Scaffold Accessories FAQs
Which scaffold accessories level a tower on uneven ground?
Leveling jacks with an attached base plate, 24 inches tall in the standard NWLJ and 12 inches in light duty, plus swivel jacks for angled surfaces.
Do scaffold outriggers include casters?
Casters are a separate item among our scaffold accessories, and each NWOR or NWLDOR outrigger needs a cross brace on its bracket to stabilize the tower.
What access do scaffold platforms need?
OSHA requires a ladder, stairway or other proper access once a platform is more than 2 feet higher or lower than the entry point, and crossbraces never count.
How much can the scaffold hoist arm lift?
The NWHA hoist arm is rated at 100 pounds with a 360 degree swivel head, even though the NWGW wheel itself is rated to 1,200 pounds.
What do chimney bracket scaffold accessories do?
They level a sloped roof between 2/12 and 12/12 pitch so 5 foot wide frames can stand around a chimney, and they work with ridge hooks.
Which pins lock scaffold accessories and frames?
Snap pins with a locking wire, toggle pins with a swivel bar, gravity pigtails and coupling pins for stacking frames.
Need help choosing the right ladder or truck equipment?
Talk to the team or send us your list and we will put a quote together.









