Aluminum Extension Ladders
28 ft Aluminum Extension Ladders for Gable Ends and Roof Access, Sized to the Rack That Carries Them and More
Closed lengths from 168 to 173.5 inches, weights from 43 to 65.5 pounds, Werner and Louisville ratings from Type II to IAA, and raising a long fly safely on 28 ft aluminum models.
Gable ends, steep roof pitches and tall two-storey eaves are where crews reach for 28 ft aluminum extension ladders, and at this length the vehicle that carries the ladder matters as much as the wall it leans on. Nation Wide Ladder quotes the Werner D1228-2, D1328-2, D1528-2 and D528-2 and the Louisville AE4228, AE3228 and AE2228, with the heavy-duty Louisville AE1200 series alongside, and our team weighs closed length, weight, duty rating from Type II to IAA, raising technique and the electrical rule for metal rails on every order.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Rack Length, Closed Size and Weight of 28 ft Aluminum Extension Models
A 28 closes to two 14 foot sections, so it needs a rack or trailer that supports more than 14 feet of ladder. Werner lists its two-section 28 ft models at 168 inches closed, and Louisville lists 172 inches for the AE3228, 172.875 for the AE2228 and 173.5 for the AE1228HD. A rack that stops short leaves the fly hanging past the tailgate, where it can be struck or work loose on a long drive.
Weight climbs quickly at this size. Werner’s D1228-2 is the lightest at 43 pounds, Louisville’s AE4228 weighs 48, the AE3228 53 and the AE2228 55, while the 375 pound models land at 59 pounds for the AE1228HD and 65.5 for the Werner D528-2. Lifting a 65.5 pound ladder onto a van roof is often a two-person job, so crew size can steer the choice between 28 ft aluminum extension ladders as much as the load does.
Because we install truck and van racks, we can match the rack to a 28 that closes at 168 to 173.5 inches when both go on the same order.
Type II Through IAA Ratings on 28 ft Aluminum Extension Ladders for Roof Crews
Both makers cover all four ratings at 28 ft. Type II at 225 pounds comes in the Werner D1228-2 and Louisville AE4228, Type I at 250 pounds in the D1328-2 and AE3228, and Type IA at 300 pounds in the D1528-2 and the Louisville AE2228, which rides on a full I-beam. At Type IAA, Werner’s D528-2 holds 375 pounds, and Louisville’s catalog lists the AE1228HD at the same rating with a MAXLOCK rung lock and QuickLatch, though our store lists the AE1200 series at Type IA, so we confirm it on the quote.
Our store lists the D1228-2 and D1328-2 as medium duty extension ladders, and the D1528-2 adds extra heavy-duty I-beams with a rail-on-rail design that widens the fly. Roof work is the reason to look hard at the top two classes. A roofer on a 28 is often carrying flashing, a bundle or a nail gun, and the climber plus all of it has to stay within the rating. A homeowner reaching a gable vent once a season sits comfortably at Type II, which is also the lightest 28 in each brand.
Tell us what goes up the rungs on a typical day and our team will match a 28 ft rating to it before the quote goes out.
Raising a Long Fly and Keeping 28 ft Aluminum Clear of Power
Each section of a 28 is 14 feet long, so the fly travels a long way as it climbs. Raise it from the ground with the base footed, let both rung locks seat and only then climb, since OSHA 1926.1053 says a ladder shall not be moved, shifted or extended while occupied. The Werner models use spring-loaded extruded rung locks with Alflo rung joints, Louisville’s AE2228 and AE3228 use the polymer MAXLOCK, and the AE4228 latches its sections with the QuickLatch. For roof access the rails must reach at least 3 feet past the eave, and Louisville lists a 25 foot maximum extended length for its 28 ft models with 27 feet 7 inches of maximum reach.
A long fly swinging upright can also reach an overhead line it would never touch leaning on the wall. Louisville marks every AE model not safe around electricity, and OSHA requires nonconductive side rails wherever the worker or the ladder could contact exposed energized electrical equipment, so plan the raise away from the service drop or move to fiberglass for that wall.
Book a free consultation at our Windham or Worcester showroom and we will walk through raising and footing a 28 before you buy.
How the 28 ft Aluminum Size Bridges Two-Storey and High Gable Work
Werner’s sizing advice is an extension ladder 7 to 10 feet longer than the highest support point, which is why a 24 often falls short at a gable peak where a 28 fits. If the peak sits higher still, the 32 foot aluminum size moves up to a pair of 16 foot sections, and our 28 ft extension ladders comparison lines these models up with fiberglass and Aerolite options. Every height sits in our aluminum extension ladder range.
When the job also needs staging, roof brackets or harnesses, you can see every maker we carry in our ladder and truck equipment brands hub.
Ordering 28 ft Aluminum Extension Ladders With Rack Fit Checked
Rack length, crew size and roof loads all shape the choice, so we quote 28 ft aluminum extension ladders with the vehicle and the climber in mind, and the Werner D1500-2 series is a ready Type IA choice, with our own trucks delivering door to door across Connecticut, Rhode Island, Massachusetts, New Hampshire, Vermont and Maine.
28 Ft Aluminum Extension Ladders FAQs
What rack length does a 28 ft aluminum extension ladder need?
One that fully supports a closed ladder of 168 inches for Werner's two-section models, or 172 to 173.5 inches for Louisville's.
Which 28 ft aluminum models are rated for 375 pounds?
Werner's D528-2 at 65.5 pounds and, in Louisville's catalog, the AE1228HD at 59 pounds. We confirm the AE1200 rating on your quote.
What is the lightest 28 ft aluminum extension option?
Werner's D1228-2 at 43 pounds, rated Type II for 225 pounds, followed by Louisville's AE4228 at 48.
Can I extend 28 ft aluminum extension ladders while standing on them?
OSHA says a ladder shall not be moved, shifted or extended while occupied, so set the length from the ground first.
How tall a gable can a 28 ft aluminum model handle?
Werner's chart averages 27 feet of reach for this size and Louisville lists 27 feet 7 inches, both for a 5 foot 7 inch climber reaching 12 inches overhead.
Is a 28 ft aluminum ladder suitable for electrical work?
Choose fiberglass for that. Louisville marks its AE models not safe around electricity, and OSHA requires nonconductive rails where the ladder could contact exposed energized equipment.
Need help choosing the right ladder or truck equipment?
Talk to the team or send us your list and we will put a quote together.






