Truck Tool Boxes

Low Side Tool Boxes in Slim, Standard and HD Deep Rail Designs, Bright or Black and More

Weather Guard 174 and 184 low side models with the K&W 300 and HD 350 Series, compared by rail height, base width, length, lid style and clearance under a ladder rack.

Fitting low side tool boxes lets a truck keep tools locked along the rails while loads still pass over the top, and Nation Wide Ladder measures the bed, quotes a matched pair and installs it. We list the Weather Guard low side box in models 174 and 184, the slim K&W 300 Series and the deeper K&W HD 350 Series with its full access lid, in bright or black.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

Why Low Side Tool Boxes Suit Trucks That Haul Over the Rails

A low side unit rises only a little above the bed rail, so plywood, drywall or lumber can still lie across the rails on top of it and the driver keeps a clear view over the bed in the mirrors. That makes low side tool storage the natural pick for remodelers, carpenters and landscapers whose loads are wider than the gap between the wheel wells, and for any truck running a ladder rack, where a low lid leaves headroom under the crossbars. Weather Guard has built super low side models since the early 1980s, so the low rail profile is a long-established design.

The trade is volume. A low tool box holds less per foot of rail than taller storage, so crews make it up with length or with a deeper model such as the K&W HD 350. If the truck rarely carries anything across the rails and the priority is the most storage you can reach from the ground, our high side tool boxes are the other route. For everyone who needs the rail line kept low, low side tool boxes keep tools locked up without giving away the load space above them.

Bring your rail height to our Windham, NH or Worcester, MA showroom and compare low side lids in person, with the consultation free of charge.

K&W Manufacturing HD 350 Series Side Mount Box

Weather Guard Low Side Models Against the K&W 300 and HD 350

Weather Guard's low side box is listed as models 174 and 184 in 47 and 56 inch lengths, 13.25 inches tall on a 10.5 inch base and 16.25 inches across overall. It carries an ARMOR-TUF powder coat in bright or black and a limited lifetime warranty, and Weather Guard also builds low profile versions in the same two lengths. The low side line can take the 1KEY ULTRALOCK, so a matched pair can open on a single key.

K&W gives a slimmer and a deeper choice. At 12 inches high the K&W 300 Series is the lowest of the three, sitting on an 8 inch base with a 12 inch overall width, in 48, 60 and 72 inch lengths, bright or black, with other sizes available. The HD 350 Series reaches 17 inches high on an 11.5 inch base and is built from .080 gauge aluminum, with a lid that opens fully and a parts tray you can lift out, in 48, 65 and 90 inch lengths. At 17 inches it actually stands taller than the 16 inch Weather Guard hi-side, so it suits a crew that wants low side mounting with near high side height.

Our team checks your rail height and bed width against all three low side tool box models, so the length and depth you order suit the truck.

K&W Manufacturing 300 Series Side Mount Box

Fitting Low Side Storage Under a Ladder Rack, From Base Width to Lid Clearance

Base width is the measurement that sits on the rail, and it decides how much floor each tool box takes. The 8 inch base of the K&W 300 leaves the most room between a pair, the Weather Guard sits at 10.5 inches and the HD 350 at 11.5, so measure between the wheel wells first when pallets or sheet goods travel down the middle. Check too for a bed liner lip, tie-down cleats or mounted tool racks, any of which can keep a low tool box from sitting flat.

Length comes next. Weather Guard takes bed length as the run between a shut tailgate and the bulkhead, and the low side units must fit within that run after any crossover or rack feet are subtracted. Fix the headache rack position before picking lengths, since its feet use up rail at the front. Under an over-bed ladder rack, compare the lid height plus its opening swing with the clearance to the rack crossbars, since a lid that hits a crossbar cannot open fully.

We don't just sell, we install, so both low side units are mounted true to the rails and checked against the rack before you drive away.

Weather Guard Lo-Side Box

Low Side Rail Storage Paired With Crossovers and Racks

Low side tool storage rarely rides alone. Deep storage at the front comes from a crossover behind the cab, a ladder rack carries long material above everything, and the low rail line lets both work without crowding each other. Our truck tool boxes overview shows how every style combines, with full maker ranges on our Weather Guard truck boxes and K&W tool boxes pages.

If the rack is on your list as well, you can compare every manufacturer we stock in our hub of truck equipment and ladder brands.

Low Side Tool Boxes Delivered and Fitted as a Pair

Nation Wide Ladder quotes low side tool boxes in matched pairs from Weather Guard and K&W, and both showrooms keep Saturday morning hours, handy for crews busy on weekdays. After more than 50 years fitting contractors' trucks, our own delivery trucks cover Maine, New Hampshire, Vermont, Massachusetts, Rhode Island and Connecticut, so the pair arrives together and goes on in one visit.

Low Side Tool Boxes FAQs

How low do low side tool boxes sit?

The K&W 300 Series stands 12 inches high and the Weather Guard low side 13.25 inches. The K&W HD 350 is the deep low side option at 17 inches.

Which low side tool box leaves the most bed floor?

The K&W 300 Series, with an 8 inch base on the rail, against 10.5 inches for the Weather Guard and 11.5 inches for the HD 350.

Can low side tool boxes go under a ladder rack?

Yes, that is one of their main uses. Check the lid height and its opening swing against the clearance to the rack crossbars before choosing a model.

What lengths do low side tool boxes come in?

From Weather Guard, 47 and 56 inches. From K&W, 48, 60 and 72 inches on the 300 Series and 48, 65 and 90 inches on the HD 350.

Can a pair of low side units share one key?

Yes, if you choose Weather Guard units fitted with the 1KEY ULTRALOCK, which Weather Guard offers on its low side line and which can be keyed alike for a pair or a whole fleet.

What does the K&W HD 350 add over the 300 Series?

It rises to 17 inches on an 11.5 inch base, uses thicker .080 gauge aluminum and opens fully, with a lift-out parts tray inside.

Need help choosing the right ladder or truck equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder