Van Mark Siding Brakes & Accessories
Van Mark Trim-A-Table TAT60 Saw Table, With a 6 Foot Boom, Pitch Protractor, Deck Extensions, Folding Legs and More
The TAT60 siding saw table for angled and gable cuts in vinyl, fiber cement and soffit, its boom, memory stops, wings and recessed saw track, and the 3001 steel folding legs.
Gable ends and angled siding cuts are slow and inconsistent with a handheld saw on sawhorses, and the Van Mark Trim-A-Table turns them into repeatable cuts at the house, supplied across New England by Nation Wide Ladder. We list the TAT60 Trim-A-Table, with a 6 foot boom saw track, pitch and degree protractor, memory stops, wing supports and up to 18 feet of material support, along with the 3001 steel folding legs that carry and stand it.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
What the Van Mark Trim-A-Table Cuts on a Siding Job
Van Mark builds its cutting tables for vinyl and fiber cement siding, cedar shakes, soffit and lumber, and the Trim-A-Table is the model for angled work. Its long boom lets a crew cut the slope for a gable end at the right pitch, piece after piece, rather than marking and cutting each panel freehand.
The TAT60 replaced the TAT50 with a longer boom and wider support, because siding and soffit panels have grown wider over time. Van Mark says the 6 foot boom allows cuts as shallow as a 2 in 12 pitch and sharper angles across wider material.
You supply the saw. Van Mark designs the table around the 7-1/4 inch circular saw a carpenter already owns, and says the track fully captures saws from 7 to 8 inches. The saw drops into the track ready to cut, then lifts out for transport. Because the protractor reads both left and right, the same setting serves both sides of a gable.
Our team can talk through the siding and trim you cut most and whether the Van Mark Trim-A-Table suits that work before you order.
Van Mark Trim-A-Table TAT60 Features, Boom to Wings
The Van Mark TAT60 Trim-A-Table centers on its 6 foot boom and saw track. A single-point locking control sets the boom position without reaching into the path of the saw, and a dual-scale protractor reads both degrees and roof pitch, working to the left and the right.
Memory stops hold a chosen angle, so a crew can move the boom and come back to the same pitch without resetting it. A rear fence keeps material square, slides left and right for longer pieces and comes off for wider panels. The saw track is recessed, so the material is supported on both sides of the blade and the table top is never cut.
Dual deck extensions support pieces up to 18 feet long and carry built-in tape rules for quick measuring. Dual wing supports slide along the decks and add up to 16 inches of width for soffit and other wide panels.
You can see the table set up and try its controls at a free consultation in our Windham NH or Worcester MA showroom.
Van Mark 3001 Legs and Transport for the Trim-A-Table
The Van Mark 3001 Trim-A-Table legs are steel folding legs that bolt to the table and fold away for transport and storage. Van Mark says they install with a Phillips screwdriver. The same leg design comes in other model numbers for other tools, with the 3002 version for 14 inch throat brakes and the 3020 for the SureCut 90, so check the number before ordering.
The table itself uses aluminum components and breaks down for a single person to carry and set up. In a van or on a trailer, keep the saw out of the track, fold the legs and strap the table flat so the boom and protractor are not knocked out of square. Packing the table the same way each night also makes it quick to find every part at the next house, and keeps the deck extensions from bending under other gear.
Van Mark makes and assembles its products in the USA and covers the legs with a one-year limited warranty.
Our own trucks deliver door to door across New England, so the table and legs can arrive at your shop together.
Setting Up and Caring for a Van Mark Trim-A-Table
Set the table on firm, level ground near the wall being sided, and extend the decks before loading long pieces so they do not tip. Lock the boom with the single-point control before each cut, check the protractor against the pitch of the roof, and set the memory stop once the first piece fits. Use the fence for square cuts and remove it when wide panels need the room. Cut a test piece from scrap at the start of each gable, since a small angle error repeats on every panel that follows.
Brush dust and chips out of the recessed track and off the tape rules at the end of the day, since debris there throws off measurements. Van Mark builds with standard off-the-shelf fasteners, and replacing a lost nut or bolt with standard hardware keeps the warranty intact.
Keep the van or trailer storage spot dry so the aluminum and tapes stay clean.
Both of our locations open Saturday mornings, which leaves time to pick up legs or parts for the table without losing a workday.
The Van Mark Trim-A-Table Beside the Brake and Staging
On a siding job the saw table usually works next to the brake, with staging and ladders on the wall. Placing the cut station close to the work cuts down trips up and down the ladder.
Compare the makers behind the rest of that setup in our ladder and truck equipment brands hub.
Order a Van Mark Trim-A-Table
Nation Wide Ladder has supplied siding contractors for over 50 years, and we quote the Van Mark Trim-A-Table with the legs and accessories your crew needs. See it with other Van Mark siding brakes and accessories and on the Van Mark brand page, or browse our Van Mark store.
Van Mark Trim-A-Table FAQs
What saw does the Van Mark Trim-A-Table use?
Your own circular saw. Van Mark designs it around a 7-1/4 inch saw and says the track captures saws from 7 to 8 inches. No saw is included.
How shallow a pitch can the Van Mark Trim-A-Table cut?
Van Mark says the 6 foot boom allows cuts as shallow as a 2 in 12 pitch.
How much material does the Van Mark Trim-A-Table support?
Its dual deck extensions support material up to 18 feet long, and the wing supports add up to 16 inches of width.
Which legs fit the Van Mark Trim-A-Table?
The Van Mark 3001 steel folding legs, which install with a Phillips screwdriver and fold for transport.
What replaced the Van Mark TAT50 Trim-A-Table?
The TAT60, which adds a longer 6 foot boom and wider support for modern siding and soffit panels.
Need help choosing the right Van Mark equipment?
Talk to the team or send us your list and we will put a quote together.






