System One Truck Racks

System One Contractor Rig Racks for Pickups and Vans, With Extension Beams, Mid Crossmembers, Work Winch Mounts and More

Heavy I.T.S. pickup builds rated to 1,250 lb, five-crossmember van builds rated to 800 lb, extension beam lengths, loading habits and the parts that turn a ladder rack into a full cargo system.

Long ladders, conduit and trim stock all have to ride somewhere other than the bed, and the System One Contractor Rig is the full-length answer we fit for New England crews at Nation Wide Ladder. We list the Heavy I.T.S. Contractor Rig for pickups, rated at 1,250 lb, and the I.T.S. Contractor Rig for vans with five crossmembers and an 800 lb rating, then help you choose the extension beams, mid crossmember, Work Winches and anchors that suit your loads.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

Who Needs a System One Contractor Rig Instead of a Lighter Utility Build

System One builds the Contractor Rig for crews whose loads change from day to day. A framing crew might carry 28 foot extension ladders on Monday and a bundle of thin-wall conduit on Tuesday, while a siding crew needs room for long, flexible trim that sags between supports. A two-truss rack handles rigid ladders well, but flexible stock needs more support points along its length.

That is where the Contractor Rig earns its weight. On a pickup, extension beams carry the front crossmember out over the cab, so long material is supported ahead of the windshield as well as over the bed. On a van, the van design spreads five crossmembers along the roof, so short and long pieces both find support. System One describes the van Contractor Rig for contractors who haul a wide mix of rigid and flexible material in short and long lengths.

If your loads are mostly ladders and nothing else, the lighter Utility model may be enough. If you never know what the next job will ask the truck to carry, the full-length build is the safer starting point.

Our team checks your truck or van and your typical loads before you order, so the rack you pick suits the material you actually carry.

System One – Heavy Duty Contractor Rack

System One Contractor Rig Models for Pickup Trucks and Cargo Vans

We list two versions. The System One Heavy Duty Contractor Rack is the pickup build with Heavy I.T.S. gussets. System One rates the standard pickup Contractor Rig at 1,000 lb, and the I.T.S. gussets lift that to 1,250 lb while adding the bores that accept Work Winches and a T-slot for tool box hangers. The frame is rust-free aluminum, and the rack can be set up with A100 sliding cargo anchors and AWW Work Winches.

The System One I.T.S. Contractor Rack for vans carries an 800 lb rating across five crossmembers. Its rear crossmember is cantilevered past the back of the van, which keeps ladders off the roof edge and rear gutter while you load. I.T.S. stands for Integrated Tie-Down System, and every System One van rack belongs to that series, so winches can be added at any time.

Both versions come with Ladder Glide low-friction inserts, and the pickup Contractor Rig adds Ladder Life anti-wear strips on every crossmember, plus color inserts to match the truck.

We install the System One Contractor Rig we sell, so the Traks, trusses and crossmembers go onto your vehicle as one fitted job.

System One I.T.S. Contractor rack

Pickup Contractor Rig Construction, Extension Beams and System One Load Ratings

The pickup Contractor Rig stands on Pick-up Traks that run along the bed rail and spread the load, with truss legs measuring 4-1/2 by 2-1/2 inches and leaning inward at 17.5 degrees. The extension beams are 5-1/2 inches tall, which is where the strength over the cab comes from, and System One makes them in 102, 120, 138 and 156 inch lengths matched to each cab and bed combination.

The beam’s horizontal flange, about a third of an inch thick, carries the sliding mid crossmember for step ladders and short material, plus add-ons such as the tall side stop. The rear crossmember lifts out using its own handles when a tall load has to go in. Fasteners are 18-8 stainless, sized in inches rather than metric, and many nuts carry nylon locking inserts, so the hardware resists both rust and vibration.

Treat each published rating as a ceiling. Speed, road surface and your suspension all affect what the rack can safely carry on a given day.

When the rack has to match a fleet, we offer custom powder coating on new System One truck rack purchases, so color is settled before installation.

Loading, Removal and Care for a System One Contractor Rig

Load the longest, stiffest items first so they sit on every crossmember, then add flexible stock on top where the extension beam or the fifth van crossmember holds it straight. Slide ladders across the Ladder Glide insert at the rear rather than dragging them over bare aluminum, and secure each item with a winch strap or tie-down before moving, since the rack is built as a complete tie-down system.

On a pickup, System One says the whole Contractor Rig unbolts in three to five minutes, while the Traks remain on the rails to restrain cargo and guard the paint. That makes a seasonal swap practical. Keep the knobs and hardware in a labeled bag so the rack goes back on without missing parts.

Every few months, check the truss mount bolts, crossmember knobs and Ladder Life inserts. The truss mount uses an oblong hole that allows about half an inch of in and out adjustment, so a leg that has shifted can be reset rather than replaced.

Bring your truck to our Windham NH or Worcester MA showroom for a free consultation, and we will look at how a System One Contractor Rig would sit on it.

How a System One Contractor Rig Fits a Full Truck Setup

The rack is only part of a working truck. Tool boxes, a transfer tank or a set of ladders all share the same bed and roof, and planning them together keeps weight low and every load reachable from the ground.

Before you settle on a layout, compare racks and boxes from every maker we carry in our ladder and truck equipment brands hub.

Order Your System One Contractor Rig

With over 50 years of serving contractors behind us, Nation Wide Ladder fits the System One Contractor Rig to the vehicle and the loads your crew carries. See where it sits among System One truck racks and the wider System One range, then browse our System One store and send us your truck details for a quote.

System One Contractor Rig FAQs

What load rating does the System One Contractor Rig carry?

The standard pickup Contractor Rig carries a 1,000 lb System One rating, the Heavy I.T.S. pickup version 1,250 lb, and the I.T.S. Contractor Rig for vans 800 lb.

Can a System One Contractor Rig take Work Winches?

Yes, in its I.T.S. form. The Heavy I.T.S. gussets on pickups and the I.T.S. brackets on every van rack accept the Work Winch assembly.

What extension beam lengths does System One make for the Contractor Rig?

System One makes pickup extension beams in 102, 120, 138 and 156 inch lengths, matched to the cab and bed combination of the truck.

How long does it take to remove a System One Contractor Rig from a pickup?

System One puts it at roughly three to five minutes. The Traks remain on the bed rail and keep working as a cargo restraint.

How many crossmembers does the System One van Contractor Rig have?

Five, with the rear crossmember cantilevered past the back of the van to protect the roof edge and gutter while loading.

Need help choosing the right System One equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder