System One Truck Racks
System One Full Access Tool Boxes in Eight Lengths, With Pivoting Lids, Dividers, Shelves, Parts Bins and More
Diamond plate aluminum top-side boxes from 48 to 96 inches, five interior layouts, Torsion Lok latching, gas spring lids and leg-free mounting on System One racks.
Digging through a jumble of cords and cases at the bottom of a truck box wastes time on every job, and System One Full Access tool boxes fix that with a lid that pivots open to the whole interior, which Nation Wide Ladder supplies and installs for New England trucks. We list the Full Access Series in 96, 90, 87, 72, 68, 65, 59 and 48 inch lengths, with open, divider, shelf, combination and bin interiors, plus the hangers and legs that mount them.

- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
What Sets System One Full Access Tool Boxes Apart on a Pickup
A conventional top-side box opens through a narrow door, so tools pile up and small parts disappear into the corners. On a Full Access box the whole lid and front pivot back together on stainless steel pins, exposing the interior from end to end. System One describes this as 100 percent access to the inside of the box.
That opening is what makes organization practical. With the full face open, tall dividers can stand power tools side by side, shelves can sit at several heights, and plastic parts bins can be lifted straight out. A saw with a cord comes out without dragging the rest of the box with it.
The boxes are designed around System One racks but can be fitted to any truck, with or without a rack. The boxes are built as part of a matched system, and the front face is angled at 17.5 degrees, the same angle System One uses for its rack legs, so a Full Access box lines up with the truss above it.
Our team will match a Full Access length and interior to your truck bed and the tools you carry before you order, so the box arrives ready to work.
System One Full Access Tool Boxes by Length and Interior Layout
We list the System One Full Access Series in eight lengths, from 48 to 96 inches, and System One will make custom sizes on request. On an 8 foot bed, the 87 inch box fits between the front and rear trusses of a System One rack.
Interiors come in five layouts. The open interior leaves the space clear for long or bulky items. The divider layout stands tall aluminum dividers on T-slot rails that slide to any position. The shelf layout adds full length shelves, and the combination layout mixes dividers and shelves. Combination with bins adds polypropylene parts bins in up to three tiers.
Lower shelves are 12 inches deep and fit the three lowest hole positions in a divider, while upper shelves are 10-5/8 inches deep and fit all seven. Bins come in six sizes, and all but the largest can take a clear hinged lid.
Since we install truck boxes along with racks, a Full Access box and its hangers can go on your truck in the same visit.
Aluminum Construction and Latches on System One Full Access Boxes
The body is .100 inch bright aluminum diamond tread plate, formed and fully welded to 3/16 inch cast aluminum end plates. The lid and base pivot on 3/4 inch stainless steel pins running in pressed bronze bearings. System One points out that many diamond plate boxes use thinner sheet, from .063 to .080 inch, so the material thickness is worth comparing.
Closing the latch turns stainless Torsion Lok rods 90 degrees, and their ends engage lugs on the base casting to pull the lid down tight. A center catch adds a third locking point. Gas springs hold the lid firmly open once it is lifted a few inches, and wind-proofing flanges with weather stripping keep driven rain and snow out. The weatherproof locks take a double sided key, and the oversized handle suits a gloved hand.
A full length tray along the upper rear wall holds bits, pencils and markers, with clips for the two smallest bin sizes.
You can see the lid, latch and interior options in person with a free consultation at our Windham NH or Worcester MA showroom.
Mounting System One Full Access Tool Boxes Without Bed Legs
On a System One rack, no holes go into the truck, because the box becomes part of the rack system. Carriage bolts slide into the T-slot of the Pick-up Trak, the pre-punched holes in the box drop over them, and the inner edge hangs from a hanger bolted into the rack gusset. That hanger needs the Heavy I.T.S. gusset, so check your rack series first.
Hanging the inner edge leaves the bed floor clear, which matters when sliding in plywood or drywall that would catch on legs. On trucks with other racks or no rack, System One supplies 3/8 by 2 inch aluminum legs, placed so the gap between them stays wider than 48 inches for sheet goods. Drill point indents on the box ends mark where to drill through about 1/16 inch of aluminum into the mounting holes.
Once fitted, check the mounting bolts after the first few weeks and keep the weather stripping clean so the lid seals well.
Our own trucks deliver door to door across New England, so a Full Access box can reach your yard ready for fitting.
Full Access Boxes, Racks and Ladders in a Single Truck Plan
Box length, rack truss spacing and ladder length all depend on each other on a pickup. Settling them together keeps every box clear of the trusses and gives each ladder a place to ride.
If you want to compare truck box makers before deciding, our ladder and truck equipment brands hub lists each brand we carry.
Request a Quote on System One Full Access Tool Boxes
With over 50 years of outfitting work trucks, Nation Wide Ladder can size, supply and install System One Full Access tool boxes to suit your bed and your tools. Compare the System One truck racks they mount to, read about the System One range, and browse our System One store.
System One Full Access Tool Boxes FAQs
What lengths do System One Full Access tool boxes come in?
System One makes the Full Access Series in 96, 90, 87, 72, 68, 65, 59 and 48 inch lengths, with custom sizes available on request.
Which Full Access box fits an 8 foot bed with a System One rack?
The 87 inch box is the usual choice, since System One gives 88 3/8 inches between trusses on an 8 foot bed.
What interiors are available in System One Full Access tool boxes?
Open, full divider, full shelf, combination, and combination with bins.
Do Full Access boxes need legs on the truck bed?
Not on a System One rack with Heavy I.T.S. gussets, where the inner edge hangs from a hanger. Aluminum legs are used on other racks.
How do System One Full Access tool boxes lock?
Torsion Lok stainless rods draw in the lid ends and a center catch adds a third point, all worked by a single latch handle with a weatherproof lock.
Need help choosing the right System One equipment?
Talk to the team or send us your list and we will put a quote together.


