Resources

Low Profile Crossover Boxes Next to Standard Models, Bed Wall Height, Weather Guard and K&W Sizes and More

How a low lid differs from a standard crossover, the Weather Guard 121, 127 and 117 and K&W 600 and 700 Series in both versions, and fitting around headache racks and spacers.

Low profile crossover boxes keep a lower lid over the bed rails than standard models, and the challenge is knowing when that height matters more than room inside the box. Nation Wide Ladder measures your pickup and compares low profile and standard crossovers from Weather Guard and K&W, including the wide and deep options, then fits them around headache racks, spacers and lift kits.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

What Low Profile Means on Crossover Boxes That Span the Rails

A crossover rests on both bed rails behind the cab, so the floor stays clear for material while tools ride locked up top. The profile is how far the box stands above those rails. A low profile model keeps its lid low, close to the rail line, while a standard model rises higher and gives the interior more room above the rail. Both share the same basic footprint, so the choice is mostly about height, sightlines and what has to clear the lid.

Weather Guard ties the decision to one measurement. Its bed measuring advice asks you to measure bed wall height, from the floor to the top of the rail, because that figure helps decide between a low profile and a standard profile box. A tall bed wall leaves more depth inside the bed, which is why a low lid can still hold a useful load there. A low box also keeps more of the rear window in view, and it leaves extra room under a ladder rack crossmember or a headache rack that sits close to the cab. Crews running several pickups often mix the two, fitting low boxes where the view matters and taller boxes where capacity does.

Our team measures bed wall height and rail width on your pickup before we quote, so the low or standard profile you choose suits that truck.

Weather Guard and K&W Low Profile Crossover Specs Compared

Weather Guard builds the 121 low profile and 127 standard on the same 20 inch footprint, and Werner’s spec sheet lists both at 11 cubic feet, the 121 at 76.5 lb and the 127 at 75 lb. Its wide 117 is the larger option at 27.5 inches front to back, 18.5 inches tall and 15.5 cubic feet. Steel versions of the three are sold as the 116, 120 and 126.

K&W offers its 600 Series crossover in both profiles, three models each. The standard CKWTB600-FL, CKWTB670-FL and CKWTB680-FL measure 70, 71 and 68 inches long, while the low profile CKWLP600-FL, CKWLP670-FL and CKWLP680-FL measure 71.5, 72.5 and 69.5 inches, all 20 inches wide. Our listings show 14.5 inches of height for both versions, so we confirm the low profile figure with K&W before quoting. The 700 Series Wide and Deep comes in both profiles too, about 22 by 20 inches as a standard model and 21.75 by 19.75 inches as a low one. Because both makers keep the width of their low and standard boxes close, a fleet can change profile from one truck to the next without changing how the boxes mount on the rails.

Our own trucks deliver door to door across New England, so a low profile model for one pickup or a matched set for several arrives without a freight terminal stop.

Weather Guard 117 / 121 / 127 Series Boxes

Fitting Low Profile Crossover Boxes Around Racks and Bed Rails

Rail width comes first, measured between the inner edges of the rails, since a crossover has to land on both with its ends supported. Then check the gap from the bulkhead to the front of the wheel well, which Weather Guard flags for its deep and wide models. A rack changes the picture. Weather Guard ships leveling spacers with its headache racks so a box sits flush with the rack feet, and the Magnum headache rack line sells toolbox spacers for the same job, with Magnum advising a box about half an inch narrower than the rack’s overall width.

Some owners want the opposite of a low lid. The System One A123 lift kit raises a crossover on 3 inch square aluminum tube spacers to free space beneath it, which suits a truck where long stock rides under the box. Choosing low profile boxes and then lifting them rarely makes sense, so settle whether the space under the lid or the view over it matters more before ordering.

We install crossovers along with racks and spacers, so a low profile box and the rack beside it go on in one visit and line up at the rails.

Weather Guard Headache Racks

Low Profile Crossover Storage in a Full Truck Setup

A crossover is one layer of a working pickup. Side units, a rack overhead and sometimes a transfer tank share the same bed, and the Weather Guard truck box range shows how those styles combine with a low profile crossover in front.

If you are weighing several makers for that layout, start with our truck equipment and ladder manufacturers hub.

Weather Guard Truck Boxes

Low Profile Crossover Boxes Quoted and Installed

Bed wall height, rail width and the rack you run decide whether a low lid suits your truck, and Nation Wide Ladder quotes low profile crossover boxes from Weather Guard and K&W against those measurements. Call 603-434-6911 in New Hampshire or 508-754-3030 in Massachusetts to start.

Low Profile Crossover Boxes FAQs

What is the difference between low profile and standard crossover boxes?

A low profile model keeps its lid closer to the rail line, while a standard model rises higher above the rails. Weather Guard uses bed wall height to help decide between them.

Do low profile crossover boxes hold less?

Not always. Werner's spec sheet lists the Weather Guard 121 low profile and the 127 standard at the same 11 cubic feet on a 20 inch footprint.

Which K&W crossover boxes come in a low profile version?

The 600 Series, as the CKWLP600-FL, CKWLP670-FL and CKWLP680-FL at 71.5, 72.5 and 69.5 inches long, and the 700 Series Wide and Deep.

How do I measure for a low profile crossover box?

Measure between the inner edges of the bed rails, the bed wall height from floor to rail top and the gap from the bulkhead to the wheel well, then note the year, make and model.

Can a low profile crossover sit next to a headache rack?

Yes. Weather Guard ships leveling spacers with its headache racks and Magnum sells toolbox spacers, both so the box sits level with the rack feet.

Can I raise a crossover box instead?

System One sells the A123 lift kit, which raises a crossover on 3 inch square aluminum tube spacers to open space beneath it.

Need help choosing the right ladder or truck equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder