Fiberglass Extension Ladders
20 ft Fiberglass Extension Ladders From Werner and Louisville in IA, IAA, Three-Section and Aerolite Builds and More
Split-level eaves and meter masts within 19 ft of average reach, nonconductive rails, a 17 ft working height, weights from 37.9 to 50 pounds and a compact three-section fiberglass option.
Electricians at a meter mast, painters under a porch service drop and gutter crews on split-levels reach for 20 ft fiberglass extension ladders whenever the job sits close to wiring. Nation Wide Ladder quotes them from Werner and Louisville. At 20 ft we compare five series, the Type IA Louisville FE3220, Werner D6220-2 and three-section D6220-3 against the Type IAA Werner D7120-2 and lightweight Aerolite B7120-2. We then match rating, weight and closed length to the person who climbs.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
What 20 ft Fiberglass Rails Reach Around Meter Masts and Split-Level Eaves
Werner’s height chart gives a 20 ft extension an average reach of 19 feet. Louisville lists 19 feet 10 inches of maximum reach for the FE3220, and both figures assume a 5 foot 7 inch climber reaching 12 inches overhead. Louisville builds its 20 from two 10 foot sections that extend to a maximum of 17 feet, and Werner gives the D6220-2 and the three-section D6220-3 the same 17 foot working height.
That puts a 20 ft fiberglass extension within range of the service entrance on a raised ranch, the eaves of a split-level, a porch roof with a drop running across it and lit signs over a shop door. OSHA requires nonconductive side rails wherever the climber or the ladder could contact exposed energized equipment, which is why fiberglass rails earn their place on these jobs. Werner advises an extension 7 to 10 feet longer than the highest support point and sets the top standing level four rungs from the top. A mast or eave close to 17 feet therefore points toward the next size up.
Send us the height of the mast or eave and our team will check it against each 20 ft fiberglass model before anything is ordered.
Type IA or IAA in a 20 ft Fiberglass Extension, From 37.9 to 50 Pounds
Two duty ratings cover fiberglass at 20. Type IA, rated for 300 pounds, comes in the Louisville FE3220 at 42 pounds and the Werner D6220-2 at 44.5 pounds. Type IAA, rated for 375 pounds, comes in the Werner D7120-2 at 50 pounds and the Aerolite B7120-2 at 37.9 pounds. Werner describes the Aerolite as 25 percent lighter than a standard 375 pound ladder because of its BOXLOK box rails.
The Aerolite is both the lightest 20 ft fiberglass model we list and one of the two rated highest, a pairing that suits crews who raise a ladder many times a day. The 20 is also the shortest Aerolite size, offered here only as the plain B7120-2, since the V-rung, leveler and cable hook versions begin at 24 ft. Everything the climber carries counts against the rating along with body weight, so an electrician hauling a meter, a drill and conduit can reach 300 pounds sooner than expected, and Type IAA leaves that margin.
We run regular weekly deliveries to Maine from New Hampshire, so a Type IAA 20 can ride along with the rest of a crew’s order.
Closed Length, Feet and Rungs on 20 ft Fiberglass Extension Models
Louisville gives closed heights of roughly 124 to 125.5 inches for its 20 ft extension models, and Werner lists 120 inches for a two-section 20. The three-section D6220-3 closes to 8 feet 4 inches with the same 17 foot working height as the D6220-2, which suits a van or a short rack, at the cost of a third section to raise and lock.
At the base, Werner fits the D7100-2 and the Aerolite with dual action feet and the D6200 series with Shu-Lok shoes and spur plates. Louisville gives the FE3220 a steel swivel safety shoe with a metal shield, a MAXLOCK polymer rung lock and its QuickLatch. Werner’s D6200 and D7100 fiberglass models use 1.63 inch D-rungs and are built to ANSI A14.5. The D7120-2 also comes with pre-pierced holes for a V-rung and cable hooks. Its base and fly separate, so the bottom section can work as a single ladder on another part of the job.
We install racks on trucks and vans, so 20 ft ladders and the racks that carry them can be sized together for the vehicle.
Where the 20 ft Fiberglass Size Sits Among Other Heights and Gear
A 20 often works beside a stabilizer that holds it off the gutter, a leveler for a sloped lawn and a step ladder for the indoor half of an electrical job. Our fiberglass extension ladders overview lays out every height in this material, the 24 ft fiberglass models take over for two-storey gutters, and the 20 ft extension ladders across both makers add the aluminum choices at this size.
When the order grows into racks, staging or harnesses, you can weigh every other maker we carry in our ladder and truck equipment brands hub.
Quotes on 20 ft Fiberglass Extension Ladders for Electrical and Exterior Work
Rating, weight and closed length decide which of the five series fits, so we quote 20 ft fiberglass extension ladders by the job. The Werner D7100-2 series is the Type IAA choice with strand-ready rails. Call 603-434-6911 or 508-754-3030 for a quote, and our trucks bring the order to New Hampshire, Massachusetts, Connecticut, Rhode Island, Vermont and Maine.
20 Ft Fiberglass Extension Ladders FAQs
Are 20 ft fiberglass extension ladders heavier than aluminum?
Usually. Louisville lists the fiberglass FE3220 at 42 pounds against 32 to 37 pounds for its aluminum 20 ft ladders, while the Werner Aerolite B7120-2 comes in at 37.9 pounds.
Which 20 ft fiberglass models carry 375 pounds?
The Werner D7120-2 and the Aerolite B7120-2 are both rated Type IAA for 375 pounds.
Can I get a 20 ft Aerolite with a cable hook?
Not at this size. We list the plain B7120-2 at 20 ft, and the CL and X versions with a V-rung, leveler or cable hook start at 24 ft.
How short does the three-section 20 ft fiberglass model close?
Werner lists the D6220-3 at 8 feet 4 inches closed, with a 17 foot working height.
Why pick fiberglass rails for a 20 ft extension near a meter?
OSHA requires nonconductive side rails where the ladder or climber could contact exposed energized equipment, and Louisville marks the FE3220 as safe around electricity.
Need help choosing the right ladder or truck equipment?
Talk to the team or send us your list and we will put a quote together.









