Alum-A-Pole Pole Scaffold
Alum-A-Pole Pump Jack Poles, From 6 to 24 Foot Lengths and Pole Joints to Two and Three Pole Packages and More
Aluminum pole lengths AP-06 to AP-24, the Alum-A-Joint, lab ratings and warranty, the eight package combinations of braces, pump jacks, workbenches and stages, plus bracing and footing.
We supply Alum-A-Pole pump jack poles to contractors and homeowners who need a steady, adjustable platform along a long wall without building wood staging on site. Nation Wide Ladder lists the four Alum-A-Pole pole lengths and the two and three pole packages that add pump jacks, braces, workbenches and a stage, and our team helps you size the pole lengths, joints and package to the height and run of the wall.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
What Alum-A-Pole Pump Jack Poles Do on Low-Rise Exterior Work
Every pump jack setup starts with the poles. They stand upright against the wall, each one carries a pump jack that climbs it, and the stages span from pole to pole. Alum-A-Pole pump jack poles replaced the wood poles siding crews used to nail together on site, and the aluminum keeps each one light enough to carry while the jacks do the lifting. Siding, painting, window and trim crews use them on residential and light commercial walls where a platform has to rise a course at a time.
Each Alum-A-Pole is structural aluminum with industrial rubber permanently bonded along one face, and that rubber goes against the outside, facing away from the building, where the pump jack grips. Alum-A-Pole rates its full pump jack system for two people and 500 pounds with a 4 to 1 overall safety ratio, and says a jointed setup can reach an OSHA-approved shoulder working height of 50 feet. Pump jack poles also link horizontally as far as the wall runs, since every added pole carries the end of the next stage.
Having served homeowners and contractors for over 50 years, we can help you decide whether Alum-A-Pole pump jack poles or a ladder setup suits the walls you face.
AP-06 to AP-24 Alum-A-Pole Poles, Lengths, Joints and Warranty
We list the Alum-A-Pole pump jack poles in four lengths, the 6 foot AP-06, the 12 foot AP-12, the 18 foot AP-18 and the 24 foot AP-24. The 6 and 12 foot lengths suit single-story eaves, porches and touch-up work, while the 18 and 24 foot pump jack poles are the usual choice for two-story siding. Our listing gives each pole a lab test to 5,000 pounds and a lifetime warranty, and Alum-A-Pole describes the warranty as limited lifetime.
When the wall runs taller than one pole, the Alum-A-Joint connects two lengths end to end. Alum-A-Pole says the joint adds vertical reach, strengthens the connection and carries two separate safety stops, and it is the part that takes a setup to the 50 foot working height. We also list the APJ 6 foot pole connector separately. A practical way to plan lengths is to pick lengths so the joint sits at a height you can assemble from the ground, then add a short pole on top rather than leaving the tall section unsupported.
Tell us the eave heights on the job and our team will work out which pole lengths and joints to list on the quote.
Alum-A-Pole Pump Jack Pole Packages With or Without a Workbench
The Alum-A-Pole pole packages group the main parts for a first setup around the 24 foot Alum-A-Pole. Each one pairs every pole with a wall brace and a pump jack, then varies by two options, the workbench and the stage. That gives eight combinations in all.
Two pole packages. Two 24 foot lengths, two braces and two pump jacks, offered with or without two workbenches and with or without one stage.
Three pole packages. Three 24 foot lengths, three braces and three pump jacks, again with or without three workbenches and one stage.
The stage in each package is a two-person, 500 pound rated plank measuring 14 inches by 24 feet. A two pole package sets up one bay, which suits a gable end or a short wall. A three pole package gives two bays along the wall, though it ships with a single stage, so plan a second one if both bays will be worked at once. The workbench rides the same pump jack poles at waist height and keeps tools and coil close to hand.
Our Windham, NH and Worcester, MA showrooms offer free in-person consultations, so you can compare the package options with us before you order.
Bracing, Footing and Care for Alum-A-Pole Poles on the Wall
Pump jack poles depend on bracing. The OSHA pump jack rule, 29 CFR 1926.452(j), calls for each pole to be secured to the structure with rigid triangular bracing or its equivalent at the bottom, the top and other points as needed. When a pump jack has to pass a brace, an extra brace goes about 4 feet above the one being passed and stays until the original is put back. The general scaffold rule, 1926.451, asks for base plates and mud sills or other firm, level footing under each pole, and for a competent person to inspect the setup before every shift.
Alum-A-Pole adds its own guidance. Keep the rubber face away from the building, install braces where the instructions call for them and avoid mixing other makers’ parts into the system, since Alum-A-Pole designs its pole, jack and stage parts to work together. Aluminum conducts electricity, so keep the whole Alum-A-Pole setup well clear of power lines.
Our own trucks deliver door to door across New England, with regular weekly deliveries to Maine from New Hampshire, so a 24 foot Alum-A-Pole reaches the site without a trailer of your own.
Alum-A-Pole Pump Jack Poles as the Spine of a Larger Exterior Kit
Pump jack poles carry the platform, but the wider job still needs ladders to reach the roof and set the first brace, a brake to bend trim and a rack on the truck long enough for 24 foot poles. Planning those together keeps the poles moving from one house to the next without a separate trip.
To see how other makers handle the ladders and racks around your scaffold, visit our ladder and truck equipment brands hub.
Price Alum-A-Pole Pump Jack Poles and Packages for Your Walls
A wall of the right height deserves a pole of the right length, and Nation Wide Ladder quotes Alum-A-Pole pump jack poles as single lengths or as packages built around your run. See how each pole fits with the rest of the system on our Alum-A-Pole pump jack scaffolding overview, read the Alum-A-Pole brand page, or browse Alum-A-Pole in our store.
Alum-A-Pole Pump Jack Poles FAQs
What lengths do Alum-A-Pole pump jack poles come in?
We list the AP-06, AP-12, AP-18 and AP-24, which are 6, 12, 18 and 24 feet long.
How strong are Alum-A-Pole pump jack poles?
Our listing says each pole is lab tested to 5,000 pounds, and Alum-A-Pole rates the full pump jack system for two people and 500 pounds with a 4 to 1 safety ratio.
How do I get more height from Alum-A-Pole pump jack poles?
The Alum-A-Joint connects two poles end to end with two separate safety stops, and Alum-A-Pole says a jointed setup reaches a 50 foot shoulder working height.
What comes in an Alum-A-Pole pole package?
Two or three 24 foot lengths with a matching number of braces and pump jacks, with workbenches and one 14 inch by 24 foot stage as options.
Which way does the rubber on an Alum-A-Pole pole face?
Alum-A-Pole says the rubber should face away from the building.
Do Alum-A-Pole pump jack poles carry a warranty?
Our listing shows a lifetime warranty, and Alum-A-Pole describes it as a limited lifetime warranty.
Need help choosing the right Alum-A-Pole equipment?
Talk to the team or send us your list and we will put a quote together.






