Staging Planks
Ladder Jacks in Short Body and Long Body Designs, With Two-Rung and Three-Rung Grips, Matching Stages, Planks and More
Werner AC10 models for 14 and 20 inch stages, the extension ratings that carry them, Werner and Louisville ladders to pair, telescoping planks, and OSHA limits on height, bearing, bridging and fall arrest.
Ladder jacks turn two extension ladders into a narrow scaffold along a wall, and the challenge is matching the jack, the stage and the ladder rating so the setup holds its load, which is where Nation Wide Ladder helps by quoting complete pairs. We supply Werner short body and long body jacks in two-rung and three-rung designs, with the aluminum stages, extendable planks and Type IA or IAA extension ladders that complete each setup.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Short and Long Body Ladder Jacks Sorted by Stage Width
Every ladder jack does the same basic job, hooking onto the rungs of an extension ladder to carry one end of a stage, and the models differ in the stage they accept and how many rungs they grip. Werner makes the three we list. The short body AC10-14-02 grips two rungs and takes stages up to 14 inches wide. The long body AC10-20-02 also grips two rungs but accepts a 20 inch stage, and the Werner AC10-20-03 spreads its hold across three rungs while taking the same 20 inch stage. Werner notes all three adjust quickly in the field, and a working setup always takes two jacks of the same model, one on each ladder, hung at the same rung height.
Choosing between ladder jacks starts with the stage your crew carries. A painter with 14 inch stages already on the truck needs the short body model, while a siding crew that wants room for material beside its feet moves to a 20 inch stage and a long body jack. OSHA’s floor for a ladder jack platform is 12 inches, so either stage width qualifies. Our Werner ladder jacks and Werner AC10 ladder jacks pages go deeper on each model.
Our team matches each jack to the stage width you own, so both ends of the setup accept the same deck from the first wall.
Extension Ratings and Stage Loads Behind Safe Ladder Jacks
The ladder carries everything the jack holds, including the stage, the workers and their material. Werner notes that OSHA and ANSI allow its jacks on 250 pound Type I extension ladders, yet it recommends Type IA ladders rated at 300 pounds or Type IAA ladders rated at 375 pounds. Fiberglass suits staging near service drops, with the Werner D6200-2 and Louisville FE3200 both rated Type IA and the Werner D7100-2 stepping up to Type IAA, while aluminum Type IA and IAA ladders suit staging well away from power. Each ladder jack setup needs two matching ladders set at the same angle, and our extension ladders best sellers compare Werner and Louisville models side by side.
Stage load counts too. Werner and Louisville stages carry 250 pounds in the one person class or 500 pounds in the two person class, and each maker offers the 14 and 20 inch widths these jacks accept. For shorter runs the Werner PA200 extendable plank, rated at 250 pounds, is made for use with ladder jacks and telescopes from 6 feet up to 17 feet across three models.
Over 50 years of supplying siding and painting crews means we can pair each set of ladder jacks with ladders and stages rated for the load.
Twenty Foot Platform Cap, Fall Arrest and Bridging Rules for Ladder Jacks
OSHA 1926.452(k) sets the limits for this kind of scaffold. The platform may not exceed 20 feet in height, every supporting ladder must meet OSHA’s ladder rules, and job-made ladders cannot support ladder jacks at all. Each jack has to rest on the side rails and rungs together or on rungs alone, and a rungs-only design needs a bearing length of 10 inches or more on every rung. Ladders must be placed, fastened or equipped to prevent slipping, and one platform may not be bridged to another, so a long wall is worked in separate bays.
Fall arrest arrives sooner than many crews expect. Above 10 feet, OSHA 1926.451 names a personal fall arrest system, not a guardrail, as the protection for a ladder jack scaffold, so harnesses and an independent anchor belong on the same order as the jacks. Each end of the stage must also extend at least 6 inches past the centerline of its support unless it is cleated or hooked, and a competent person must inspect the scaffold before each shift and after anything that could affect it.
Send your stage width and ladder series to 603-434-6911 or 508-754-3030, and we quote jacks, ladders and stages that stay inside those limits.
Ladder Jacks Next to Pole and Frame Staging
Ladder jacks cover the lower part of a wall quickly, and taller elevations or long continuous runs move to pump jack poles or frame scaffolding, with every option sharing the same stages and planks. Our staging planks section sets out the decks, guardrails and nets that serve all three.
For the scaffold, ladder and rack makers that carry a crew past jack height, open our brands we carry for ladders and staging hub.
Ladder Jacks Quoted Together With Their Stages and Uprights
Nation Wide Ladder quotes ladder jacks in matched pairs with the stages and Type IA or IAA ladders that carry them, from showrooms in Windham, New Hampshire and Worcester, Massachusetts, and our own trucks deliver across Connecticut, Rhode Island, Massachusetts, New Hampshire, Vermont and Maine.
Ladder Jacks FAQs
Which ladder jacks take a 20 inch stage?
The Werner AC10-20-02 two-rung and AC10-20-03 three-rung long body models, while the short body AC10-14-02 stops at 14 inch stages.
What ladder rating do ladder jacks need?
Werner recommends Type IA ladders rated at 300 pounds or Type IAA ladders rated at 375 pounds, while noting that OSHA and ANSI allow 250 pound Type I extension ladders.
How high can a ladder jack platform go?
Under OSHA 1926.452(k), no ladder jack platform may sit higher than 20 feet.
Can two ladder jack platforms be bridged together?
No. OSHA bars bridging one ladder jack scaffold platform to another, so a long wall is worked in separate bays.
Which planks work with ladder jacks?
Werner and Louisville aluminum stages in 14 or 20 inch widths, rated at 250 or 500 pounds, and the Werner PA200 extendable plank, which Werner makes for use with ladder jacks.
Need help choosing the right ladder or truck equipment?
Talk to the team or send us your list and we will put a quote together.







