Brand spotlight

Vantech Van Racks, With H1, H2 and H3 Ladder Racks, Crossbars, Rollers, Tie-Downs, Conduit Carriers and More

Steel and aluminum roof systems from a rack maker founded in Brooklyn in 2006, rated by the mount and fitted to Ford, Chevrolet, GMC, Nissan, RAM and Mercedes cargo vans.

Ladders, pipe and lumber need a secure place on the roof of a work van, and Nation Wide Ladder fits Vantech van racks to that job, checking the fit for your van and installing the system for you. We supply the steel and aluminum Vantech H1 Series, the H2 Series with its adjustable rear roller and the three-bar H3 Series, along with the crossbars, ladder stops, sliding anchors, ratchet tie-downs, rear rollers and 6 inch conduit carriers that complete a Vantech rack.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

Where Vantech Van Racks Fit a Trade Fleet

Vantech has built roof systems for working vans since 2006, and its racks carry ladders, conduit, pipe and lumber for electricians, plumbers, HVAC crews and general contractors. The Vantech catalog reaches past van racks to pickup racks, box truck systems and van shelving. We carry the van side of that range, with Vantech listings for the Ford Transit and Transit Connect, Chevrolet Express, GMC Savana, Nissan NV, RAM ProMaster, Mercedes Sprinter and Ford E-Series.

Two categories organize the Vantech range we list. Van roof racks hold the H1, H2 and H3 systems themselves, in steel or aluminum, with two or three bars. Rack accessories hold the parts you add once a Vantech rack is on the roof, from crossbars and ladder stops to tie-downs, rollers and conduit tubes. Pick the van, then the rack, then the load securing that goes on it.

Vantech Van Rack History, From a 2006 Brooklyn Start to Two Coasts

Vantech opened in Brooklyn, New York, in 2006, building ladder racks and van storage for tradespeople whose gear had to hold up on the job. Twenty years on, the company keeps its headquarters in Amityville, New York, runs a West Coast warehouse in Riverside, California, and ships from whichever one sits closer to the buyer. Vantech says its racks are engineered in the USA, and its catalog now runs past 500 products for more than 50 vehicle makes, covering van ladder racks, cargo racks, van shelving, truck bed racks and complete trade packages.

Two habits run through the Vantech catalog. The first is fitment by vehicle, with Vantech van racks matched to the make, model, wheelbase and roof height of the van, plus universal versions that bolt on with drilling for vans without a listed fit. The second is a load rating stated in pounds for each Vantech system, so you can set one rack against another on a single number. Vantech hardware and packaging carry a V logo with the words Van & Truck Cargo System or Van & Truck Cargo Management, which helps when you need to identify an older Vantech rack before ordering parts for it.

We have served homeowners and contractors for over 50 years, long enough to see how a rack choice plays out over the working life of a van, and we bring that to your Vantech quote.

Vantech A03 – Side Stops

Vantech Van Roof Racks, Product Lines and Rack Accessories We Carry

Van roof racks. Our Vantech van roof racks category gathers the complete systems, from steel and aluminum H1 racks to the aluminum H2 and H3, with Vantech fits listed for full-size and compact cargo vans.

H1 Series. The Vantech H1 Series sits on 2 by 1 inch rectangular crossbars, with four eyehooks on each mounting base for tie-downs, in two-bar and three-bar builds and in black, white or silver.

H2 and H3 Series. Vantech H2 and H3 racks run on extruded aluminum crossbars. The H2 Series we list spaces its crossbars 16 inches apart and adds an adjustable rear roller, while the H3 is a three-bar rack sized to one van at a time.

Accessories. Vantech rack accessories cover replacement H1 and H3 crossbars, the A57 ladder stop, A03 side stops, A20 sliding anchors, RTD ratchet kits, rear roller bars and 6 inch by 128 inch conduit carriers.

Tell us the van, the ladders and the stock you haul, and our team will check which Vantech system and parts fit before you order.

Vantech A20 – Sliding Cargo Anchors

How Vantech Rates Van Racks by the Mount, in Steel and Aluminum

Vantech applies one rating rule across its rack lines, with each mount holding 125 lbs, so capacity grows as mounts are added. That is why the totals change by system and by van. Vantech lists the H1 at 500 to 750 lbs depending on the build, with the universal H1 rated at 500 lbs total and the H1 for the 2015 and newer Ford Transit at 750 lbs total. The H3 is rated at 750 lbs on full-size vans and 500 lbs on the compact Transit Connect, Metris, NV200 and ProMaster City, and the newer H2.1 carries 750 or 1,000 lbs depending on how many mounts the configuration uses.

Material is the second decision. The H1 comes in steel or aluminum, while the H2 and H3 are aluminum. On the H1, each upright stands on an 8 inch wide base at 10.5 inches tall, welded to the post so the joint is sealed, and a rubber cap on top cuts wind noise and keeps water out. A bar guard over each crossbar gives ladders a protective surface rather than bare metal. Those ratings cover the whole load, fittings included, so weigh the gear before you choose between Vantech van racks.

We install the Vantech racks we supply, setting the mounts on your van so the load bears on the points Vantech rated.

Vantech A57 – Ladder Stop

Choosing Vantech Racks for a Ford Transit, Sprinter, ProMaster or Express Van

Start with the van. Vantech matches its vehicle-specific racks by make, model, wheelbase and roof height, and the H2 Series we list covers low, medium and high roofs on all wheelbases. If your van has no listed fit, the universal H1 bolts on with drilling, while the H1 for the Ford Transit installs with no drilling at all.

Next, count the bars. A two-bar rack suits one ladder and light stock, and a three-bar rack spreads a longer load across more mounts, which also lifts the rated total. Steel and aluminum H1 builds share the same rectangular bar and upright design, so you can choose by finish and preference.

Loading is the last question. If one person loads ladders alone, a rear roller lets the ladder roll onto the rack rather than being lifted, and the H2 Series we list includes an adjustable one. Electricians who carry conduit add a 6 inch conduit carrier, and anyone running Vantech van racks with straps should plan on ratchet tie-downs and a ladder stop from the start, since those parts are what hold the load once the van is moving.

Bring the van to our Windham, NH or Worcester, MA showroom for a free consultation, and we will look over the roof before quoting a Vantech system.

Vantech H1 Series – Aluminum Cross Bar

Vantech Racks Beside the Shelving Inside the Van

A roof rack is half of a van upfit. Long items ride on top, while bins, drawers and shelving keep small parts inside, and Vantech builds both, along with trade packages for general contractors, plumbers, electricians and HVAC crews that are configured to the wheelbase and roof height when ordered. Planning the roof and the interior together keeps the ladder, the pipe and the parts each in a place you can reach.

If you are weighing Vantech against other rack and shelving makers, you can see each manufacturer we carry in our ladder and truck equipment brands hub.

Vantech Aluminum Cross Bar H3

Order Vantech Van Racks Through Our New England Team

Browse the Vantech products we list, or call 603-434-6911 in New Hampshire or 508-754-3030 in Massachusetts to start a quote.

Nation Wide Ladder quotes, installs and delivers Vantech van racks across New England on our own trucks, with shipping anywhere in the US, so the rack you choose reaches your van ready for the next job.

Vantech Van Racks FAQs

Where are Vantech van racks made?

Vantech describes its racks as engineered in the USA. The company was founded in Brooklyn, New York, in 2006, has its headquarters in Amityville, New York, and ships from warehouses in New York and California.

How much weight do Vantech racks hold?

Vantech rates each mount at 125 lbs, so the total depends on the system. The H1 runs from 500 to 750 lbs, and the H3 is rated at 750 lbs on full-size vans and 500 lbs on compact vans.

Which vans do Vantech van racks fit?

Our Vantech listings cover the Ford Transit and Transit Connect, Chevrolet Express, GMC Savana, Nissan NV, RAM ProMaster, Mercedes Sprinter and Ford E-Series. Vantech also makes a universal H1 rack that installs with drilling.

Are Vantech racks steel or aluminum?

Both. The Vantech H1 Series comes in steel or aluminum, and the H2 and H3 Series are aluminum.

Do you install Vantech van racks?

Yes. We install the racks and truck equipment we sell, and we deliver across New England on our own trucks.

How do I get a price on a Vantech rack?

We sell on a quote basis. Send us your van and the rack you want, or call 603-434-6911 in NH or 508-754-3030 in MA.

Need help choosing the right Vantech equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder