Vantech range
Vantech Rack Accessories, With Ladder Stops, Sliding Anchors, Crossbars, Rear Rollers, Conduit Carriers and More
Parts that hold a ladder still, carry pipe in a sealed tube, add or replace a crossbar and let one person roll a load onto the roof, sized to Vantech crossbar profiles.
A roof rack is only half finished until the load is secured, and Nation Wide Ladder supplies the Vantech rack accessories that finish it, checking each part against your rack before we quote. Our range covers the A57 ladder stop, A03 side stops and A20 sliding anchors, replacement H1 and H3 crossbars, rear roller bars, 6 inch by 128 inch conduit carriers with dividers, the Push2Secure and RTD ratchet kits for the H1 and H3.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Why a Vantech Rack Needs Accessories Before the First Load
A bare set of crossbars will carry a ladder, but it will not stop that ladder sliding forward under braking or drifting sideways in a turn. Vantech designs its accessories to close those gaps, and it groups them by job, with ladder rollers and stoppers, bar guards, conduit carriers, ratchet tie-downs, wind foils and mounting hardware built to fit Vantech systems. Most of what a trade van carries on the roof needs at least a stop at the front and a strap across the top.
Fit is the reason to buy Vantech parts for a Vantech rack. The crossbar profile decides which accessories clamp on, and Vantech uses the A285 and A286 profile across the H2.1, H3, J-Series and P-Series racks, while the H1 runs on its own 2 by 1 inch rectangular bar. A ladder stop made for one profile may not seat on the other, which is why the rack series comes first when we quote Vantech rack accessories. Several Vantech accessories are also listed for pickups and work trucks, so the same parts can serve a mixed fleet.
Our team checks each accessory against the rack series and van you run, so the parts you order clamp onto the bars you already have.
Keeping Ladders in Place, Vantech Rack Stops and Sliding Anchors
The Vantech A57 ladder stop blocks a ladder and other material from moving forward. Vantech coats its top in rubber to protect equipment and bends the tip so the stop holds the ladder down and cuts rattling. It fits A285 and A286 crossbars, including the H2 aluminum systems, the H3 and the J and P Series, and Vantech lists it at 75 lbs. Vantech recommends pairing it with hook and loop straps.
Side movement is the job of the A20 and the A03. Vantech sells the A20 in pairs as an adjustable guide with an eyehook on top, which you can place anywhere along a channeled crossbar to keep equipment from shifting left and right, and the eyehook gives bungees and ratchet straps an anchor point. We list it as the A20 sliding cargo anchor. The A03 side stops round out the set for racks that carry more than one ladder.
Bring your ladders to our Windham, NH or Worcester, MA showroom for a free consultation, and we will lay out where each stop and anchor should sit.
Crossbars, Rollers and Conduit Carriers Among Vantech Accessories
Crossbars wear and bend over time, and Vantech sells them on their own. We list a replacement H1 crossbar and the H3 aluminum crossbar, which let you swap a damaged bar or add a bar to a two-bar rack. For conduit and pipe, the Vantech CC conduit carrier is a 6 inch diameter tube 128 inches long with dividers. Vantech supplies its 6 by 128 inch kit with a hatch and cap and two to four tubes in black or silver aluminum, installed onto the crossbars, and it also sells the hatch and cap alone for a length of 6 inch PVC.
Rollers save the lift. A rear roller bar lets a ladder be rolled onto the rack from behind the van rather than raised overhead, which is a help when one person loads alone. Vantech makes a 54 inch roller on 36 inch extension plates for its GFY and H3 racks and a roller-type front and rear add-on for the H2.1, in 39 inch widths for mid-size vans and 49 inch widths for full-size vans.
We install the rollers, crossbars and conduit carriers we supply, so each part is mounted square on the rack.
Ratchet Kits and Strap Accessories for Vantech Rack Loads
Straps are the last layer of a secure load. Vantech makes its RTD ratchet tie-down in versions for the H1, H2, H3 and M1 racks, each with 10 foot straps of heavy-duty nylon webbing for loads that need real tension. We list the Vantech RTD-H1 and RTD-H3 ratchet kit and a separate RTD-H3 kit, and the Push2Secure sits with them in our cargo van rack accessory listings.
A hook and loop strap is quick for a single ladder held by a stop, while a ratchet strap suits a stack of material or a load that must not shift at highway speed. Vantech also sells rubber bar guards in 65 and 72 inch lengths, which sleeve over a crossbar so a ladder or stock rests on rubber rather than bare metal and resists sliding. Check straps and guards for wear at the start of each season and replace any that are frayed or split.
Send us a list of the accessories you need and we will return one quote for the full set, or call 603-434-6911 in NH or 508-754-3030 in MA.
Vantech Rack Accessories on Pickup and Work Truck Racks
Vantech accessories are not limited to vans. The ladder stopper and rubber bar guards are listed for pickups, the Honda Ridgeline and RAM 1500, 2500 and 3500 trucks, since Vantech uses the same crossbar profile on its P-Series truck racks, and we list Vantech parts under truck rack accessories as well as cargo van accessories.
For the other rack and truck equipment makers whose accessories you might be weighing, browse our ladder and truck equipment brands hub.
Add Vantech Rack Accessories to Your Quote
Browse our cargo van roof rack accessories, or see the full Vantech van rack range.
Nation Wide Ladder fits Vantech rack accessories to the rack you already run and installs them, with regular weekly deliveries to Maine from our New Hampshire location.
Vantech Rack Accessories FAQs
Do Vantech rack accessories fit any Vantech rack?
Not all of them. Vantech uses the A285 and A286 crossbar profile on the H2.1, H3, J-Series and P-Series, and a rectangular bar on the H1, so we check the rack series before quoting.
What does the Vantech A57 ladder stop do?
It blocks a ladder from moving forward. The top is rubber coated and the tip is bent to hold the ladder down, and Vantech lists it at 75 lbs.
What size is the Vantech conduit carrier?
The Vantech CC conduit carrier we list is 6 inches in diameter and 128 inches long, with dividers.
Which ratchet kit fits a Vantech H1 or H3 rack?
We list a combined RTD-H1 and RTD-H3 ratchet kit and a separate RTD-H3 kit. Vantech RTD kits use 10 foot nylon straps.
Can Vantech rack accessories go on a pickup rack?
Some can. Vantech lists the ladder stopper and rubber bar guards for pickups and RAM trucks, and we carry Vantech parts under truck rack accessories too.
Need help choosing the right Vantech equipment?
Talk to the team or send us your list and we will put a quote together.










