Fall Protection Equipment

Safety Lanyards in Shock-Absorbing, Twin Leg, Positioning, Cable, Chain, Leading Edge and Arc Flash Builds and More

Fall arrest, positioning and restraint jobs told apart, DeCoil, SoftCoil, cable and chain builds compared, lengths from 2 to 6 feet, hook rules, OSHA strength figures and fall clearance.

Picking safety lanyards means matching the absorber, length and hooks to the job and to the clearance under the work, and Nation Wide Ladder makes that match across the Werner range we list. Our selection covers single leg and twin leg shock-absorbing models, DeCoil Stretch and SoftCoil designs, web, cable and chain positioning connectors, tie-back and leading edge models and Kevlar arc flash builds.

NH603-434-6911MA508-754-3030

  • Over 50 years serving contractors
  • MA, NH, CT, ME, VT & RI
  • Weekly Maine deliveries

Fall Arrest, Positioning and Restraint Safety Lanyards Told Apart

We sort safety lanyards into three jobs, and the job decides the build. Fall arrest models carry a shock pack or energy-absorbing core that slows a falling worker, and Werner rules out any connector without one for arrest. Positioning models hold a worker against a wall, form or pole from the hip D-rings, and OSHA requires them to be rigged so free fall cannot pass 2 feet, on an anchorage rated for twice the potential impact load or 3,000 pounds, whichever is greater. Restraint keeps the worker from reaching the edge at all, and Werner accepts its shock-absorbing models for that role because a restrained worker cannot load the pack.

Movement adds a second question. A single leg leaves a gap each time the worker unclips to pass an obstruction, while a twin leg lets the free side go onto the next anchor first, which is how steel and scaffold crews keep 100 percent tie-off. Rebar crews add short positioning safety lanyards between the hip rings and the steel. Wrapping a beam and clipping back to the strap is allowed only on the tie-back safety lanyards Werner builds for it. Our fall protection best sellers place safety lanyards beside the harnesses and anchors they connect.

Our team helps you select the job type for each worker first, so arrest, positioning and restraint safety lanyards end up on the right harness.

Werner Fall Protection C111102 2FT Web Positioning Lanyard (1in Web, 2 Snap Hook)

DeCoil, SoftCoil, Cable and Chain Safety Lanyards Crews Order Most

The Werner C311100 is the everyday 6 foot safety lanyard, with 1 inch wear-indicating polyester webbing and a DCELL pack that tears in a controlled way. The C341100 DeCoil Stretch pulls in from 6 feet to 4 feet when slack to cut tripping, and SoftCoil models such as the C351100 absorb energy along a full-length core with an impact indicator. Twin leg versions follow in the C411 and C441 ranges, and the C411120 twin leg has an extra-thick pack rated for 12 feet of free fall from a foot-level anchor at 310 pounds, dropping to 6 feet when the worker weighs up to 400 pounds.

Hot and abrasive work points to the C161 cable range, in 1/4 inch vinyl-coated cable, and the C461120LE twin leg cable model is approved for leading edges over steel beam, precast concrete and B-deck. Web positioning straps such as the C111106 come from 2 to 6 feet, the C191204 is a 22 inch Grade 80 chain rebar model, and arc flash crews take Kevlar safety lanyards such as the C811100, which Werner lists to ASTM F887 and ANSI Z359.13.

Hold a DCELL pack, a SoftCoil core and a cable safety lanyard in hand at a free consultation in Windham or Worcester before choosing.

Werner Fall Protection C111106 6FT Web Positioning Lanyard (1in Web, 2 Snap Hook)

Length, Hooks and Clearance When Choosing Safety Lanyards

Werner makes shock-absorbing safety lanyards in 3, 4, 5 and 6 foot lengths, with 6 feet the maximum, and the shortest length that lets the work get done keeps the fall short. Free fall and pack deceleration both eat into the height under the deck, so a 6 foot lanyard tied off low on a short deck can run out of room, which is why Werner publishes clearance charts for plotting the job. Only models built for it belong on a foot-level anchor or at an unprotected edge.

Hardware rules come next. OSHA requires a 5,000 pound minimum breaking strength, locking snap hooks, and D-rings and snap hooks proof-tested to 3,600 pounds. Werner warns against two snap hooks in one D-ring and against clipping a hook onto webbing or a horizontal lifeline, since each can cause rollout, and it never allows a lanyard on a self-retracting lifeline. Where more reach is needed, a longer retractable from our self-retracting lifelines replaces the lanyard. Any safety lanyard with a torn pack, frayed webbing or kinked cable comes out of service.

List the anchors and tasks for us, or phone 603-434-6911 in NH or 508-754-3030 in MA, and our quote will name safety lanyards with the right hooks.

Werner Fall Protection C111103 3FT Web Positioning Lanyard (1in Web, 2 Snap Hook)

A safety lanyard is only as good as the anchor above it and the harness it clips to, so we quote the three as one set. Werner details every connector family, from DeCoil to rebar positioning, on our Werner lanyards page, while the climb to the anchor brings in ladders and staging from other makers.

If the order reaches into ladders, racks or staging as well, you can sort the makers in our ladder and truck equipment brands hub.

Werner Fall Protection C111104 4FT Web Positioning Lanyard (1in Web, 2 Snap Hook)

Safety Lanyards Quoted to Match Your Anchors

Nation Wide Ladder quotes safety lanyards for the anchors and tasks you describe, pairing an arrest, positioning or restraint safety lanyard with each harness on the crew. Our trucks carry the order to Massachusetts, Connecticut, Rhode Island, Vermont and New Hampshire, Maine gets a regular weekly run from Windham, and we ship to the rest of the country.

Safety Lanyards FAQs

What is the difference between shock-absorbing and positioning safety lanyards?

Shock-absorbing safety lanyards carry a pack or core that slows a falling worker. Positioning models have no energy absorber, so Werner limits them to positioning and restraint.

How long can safety lanyards be?

Werner tops out its shock-absorbing models at 6 feet and also offers 3, 4 and 5 foot versions, while web positioning straps run from 2 to 6 feet.

When do crews need twin leg safety lanyards?

When the work moves between anchors. A twin leg lets the worker clip the free side to the next anchor first, so the worker never goes untied while moving.

Can I clip a safety lanyard onto a self-retracting lifeline?

No. Werner forbids that connection, so when a lanyard runs short the answer is a longer retractable.

Which safety lanyards suit a leading edge?

Only models marked for it, such as the Werner C461120LE twin leg cable lanyard, which is approved over steel beam, precast concrete and B-deck.

What strength does OSHA require from a safety lanyard?

A minimum breaking strength of 5,000 pounds, with locking snap hooks and D-rings and snap hooks proof-tested to 3,600 pounds.

Need help choosing the right ladder or truck equipment?

Talk to the team or send us your list and we will put a quote together.

TOP
Nation Wide Ladder

Nation Wide Ladder