Werner Fall Protection Anchors
Werner D-Bolt and Beam Anchors, Forged D-Bolt Rings, a Sliding Beam Anchor, Stanchions and Lifeline Kits, and More
Steel-structure tie-off compared across the A320001 forged D-bolt ring, the 30 inch sliding beam anchor, the end stanchion and rope or cable lifeline kits supplied with D-bolt ends.
Werner D-bolt and beam anchors give steel erectors and maintenance crews a tie-off point on structural steel, either a forged D-bolt ring fixed at a set point or a beam anchor that slides along the flange with the worker. Nation Wide Ladder supplies the Werner 550030 sliding beam anchor for flanges 12 to 30 inches wide, the L400001 end stanchion with its A320001 D-bolt, and rope and cable horizontal lifeline kits that ship with D-bolt anchors.
- Over 50 years serving contractors
- MA, NH, CT, ME, VT & RI
- Weekly Maine deliveries
Where Werner D-Bolt and Beam Anchors Fit on Structural Steel
Steel work needs anchorage that suits the member in front of the crew. A Werner D-bolt gives a fixed point at one location, and Werner uses it at the ends of horizontal lifelines and on its aluminum end stanchion. A sliding beam anchor instead fits across the flange and travels with the worker, so an ironworker or maintenance tech moving along the steel stays connected without stopping to reset the anchorage. Werner lists the slider and the forged ring under ANSI Z359.18-2017, the standard for anchorage connectors, so fixed and traveling options share one benchmark.
That split decides most orders for steel erectors, painters and maintenance crews on plant structures. Fixed D-bolt points suit a horizontal line or a single tie-off location, while the slider suits travel along one horizontal member. Many steel jobs use both, with Werner D-bolt ends holding a horizontal line across a bay and a Werner slider for work along a single member. Werner rates the slider as temporary, so it moves from job to job, while a D-bolt fitted at the end of a kit comes down with the line when the phase is finished.
Roof and post anchorage for other structures sits in our Werner fall protection anchors range.
Our team reviews the steel sizes and the movement your crew needs, so the Werner hardware on your quote fits the structure.
Werner D-Bolt Rings, Beam Sliders, Stanchions and Matching Lifeline Kits
The Werner A320001 is the D-bolt ring itself, forged steel plated for corrosion resistance and listed to ANSI Z359.18-2017 Type A. Werner supplies the unthreaded ring only, with no bolt, so the bolt has to be specified from the Werner D-bolt user instructions and the steel it passes through.
The Werner 550030 30 inch beam slider, which Werner numbers A550030, is an aluminum sliding anchor for beam flanges 12 to 30 inches wide and up to 2.5 inches thick, about 36 inches long and 8.2 pounds, with a 5,000 pound minimum breaking strength. Werner lists the beam slider as temporary and as meeting OSHA 1910.140 and 1926.502 and ANSI/ASSP Z359.18-2017.
The L400001 Werner end stanchion is a 7.5 foot aluminum post with a 4 inch outside diameter that comes with an A320001 D-bolt attached, raising a cable horizontal lifeline above the workers. D-bolt anchors also ship with the L120 and L122 rope kits and with the L123030 cable kit and L123060.
Stanchions, sliders and lifeline kits can travel together on our own trucks door to door across New England, and we ship anywhere in the US.
Strength Rules and Inspection for Beam and D-Bolt Anchorage
OSHA requires personal fall arrest anchorage to support 5,000 pounds per attached worker, unless a qualified person designs it as part of a complete system with a safety factor of at least two, and horizontal lifelines must be designed, installed and used under a qualified person. The beam slider carries a 5,000 pound rating of its own, while the D-bolt ring arrives without its bolt, so the finished D-bolt anchorage depends on following the Werner instructions for the bolt and the steel.
Werner warns that horizontal lifeline kits are tested as complete systems and their parts are not interchangeable, so keep the D-bolt ends that come with a kit on that kit. Werner also points users of the horizontal kits to the instructions for clearance requirements, which a qualified person should check before the first worker clips in.
Inspect each anchor before use and at least yearly by a competent person other than the user, and remove any that has arrested a fall until a competent person confirms it is undamaged. Werner publishes an anchor inspection sheet for both the slider and its D-bolt anchors.
Bring your flange sizes to our Windham or Worcester showroom for a free consultation, and we will check the slider flange range against them.
Werner Beam Anchors and the Way Crews Reach the Steel
A beam anchor is set by someone who first had to reach the steel by ladder, lift or staging, and steel crews also rely on truck racks and storage to get the gear to site. Those pieces often come from different manufacturers, so plan access and anchorage together. Werner covers the anchorage itself, which leaves the remaining choices about reaching it safely.
To compare the other manufacturers we carry for that gear, look through our ladder and truck equipment brands hub.
Quotes on Werner D-Bolt and Beam Anchors for Steel Work
Forged D-bolt rings, a sliding beam anchor for flanges up to 30 inches, and D-bolt stanchions and kits give steel crews fixed and traveling anchorage from one maker. Send us your beam sizes and the tie-off layout, call 603-434-6911 or 508-754-3030, and we will quote Werner D-bolt and beam anchors to fit. Browse our Werner store or go back to the Werner brand page.
Werner D-bolt and Beam Anchors FAQs
Does the Werner A320001 D-bolt include the bolt?
No. Werner supplies the forged, plated D-bolt ring only, without a bolt.
What beam sizes does the Werner beam slider fit?
Beam flanges 12 to 30 inches wide and up to 2.5 inches thick.
How strong is the Werner 550030 beam anchor?
Werner lists a minimum breaking strength of 5,000 pounds for the A550030 30 inch sliding beam anchor.
Which Werner lifeline kits come with D-bolt anchors?
The L120 and L122 rope horizontal kits and the L123 cable horizontal kits, plus the L400001 end stanchion.
What standard covers Werner D-bolt and beam anchors?
Werner lists both the A320001 D-bolt and the A550030 beam slider against ANSI Z359.18-2017, the anchorage connector standard.
Need help choosing the right Werner equipment?
Talk to the team or send us your list and we will put a quote together.








